Commit graph

42850 commits

Author SHA1 Message Date
Koen Vandeputte
f3b80c36bb ar71xx: fix sysupgrade generation for some targets
These targets are already defined as having a dynamic partition
but the safeloader was not adapted for them.

This causes a build warning for the sysupgrade image being too big.

Targets:
- c58-v1
- c60-v1
- c60-v2
- TL-WR1043 v5
- TL-WR902AC v1
- TL-WR942N V1

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
Koen Vandeputte
7c78be1b74 ar71xx: switch more targets to dynamic partitioning
Targets:
- TP-LINK ER355
- TP-LINK C25 V1
- TP-LINK C59 V1
- TP-LINK C7 V4
- TP-LINK C7 V5

Fixes build issues seen due to the kernel being too big

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
Radek Dostál
9d35b68776 ar71xx: switch TP-Link RE450 v1 to dynamic partitioning
As mentioned in commit 5f24933 recent changes on ar71xx (switch to 4.14,
memory compaction, ...) cause an increase in kernel size, making it too
big for RE450.

RE450 images were not build due to the following error message:
os-image partition too big (more than 1572864 bytes): Success

Tested on RE450, device boots and was used to send this patch.

Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[rewrote commit msg keeping it tight + fixed SoB lines]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
David Bauer
f89fc43a50 ar71xx: move OCEDO Koala to generic and use dynamic partitioning
This changes the OCEDO Koala flash-layout to a unified firmware
partition, thus making the ar71xx-generic kernel fit in flash.

Compile and runtested on OCEDO Koala.

Signed-off-by: David Bauer <mail@david-bauer.net>
[small title reword]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
Mathias Kresin
374e646724 ath79: fix PQI Air Pen support
Use the correct dts filename. It has to be <soc>_<manufacturer>_<device>.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-28 11:03:49 +01:00
YuheiOKAWA
27eae6597e ath79: add support for PQI Air Pen
SoC: AR9330 (or AR9331 revision?)
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Flash 8MiB. (factory is dual image)
1. write image is use half 4MiB size from factory.
  write initramfs image to mtd6 and mtd7.
2. change next boot setting. next is mtd6 boot.
  echo -ne "\x01" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

3. rewrite sysupgrade image.
  change next boot setting. next is mtd4.
  echo -ne "\x00" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

OEM mtd.
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "ART"
mtd3: 00010000 00010000 "NVRAM"
mtd4: 00140000 00010000 "uImage"
mtd5: 00280000 00010000 "rootfs"
mtd6: 00140000 00010000 "uImage2"
mtd7: 00280000 00010000 "rootfs2"
mtd8: 00010000 00010000 "CONF"

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-10-28 10:59:14 +01:00
Roger Pueyo Centelles
23f9b2d9a9 ath79: Add support for Ubiquiti LiteAP ac (LAP-120)
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.

CPU:    Atheros AR9342 SoC
RAM:    64 MB DDR2
Flash:  16 MB NOR SPI
Ports:  1 GbE port (PoE in)
WLAN:   5 GHz QCA899X (PCI)

The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).

Installation procedure is the same as the NanoStation [loco] AC:

1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-10-28 10:59:09 +01:00
Felix Fietkau
8edce6014a mt76: update to the latest version
fdc63f1 mt76: fix regression in tx status handling

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-27 17:54:37 +02:00
Daniel Engberg
4056be58f3 mt76: Fix dependencies for PCI support
USB support doesn't necessarily mean that there's
PCI support available so move that to the drivers
which requires PCI support. This applies to the
sunxi platform for instance.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix mt76x0e]
2018-10-26 17:23:38 +02:00
Felix Fietkau
6026356578 mt76: update to the latest version
0b8b15f mt7603: use common mmio mcu struct
d612e2e mt76: mt76x02: skip station tx status for non-sta wcid entries
d89d84b mt76: mt76x02: only override control->sta on sw-encrypted tx
9d59d2a mt76: add support for reporting tx status with skb
ed17ba2 mt7603: use common tx status handling code
14b6c59 mt76x0: use band parameter for LC calibration

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-25 22:49:08 +02:00
Philip Prindeville
a6d02a7572 grub2: fix regression caused by binutils-2.31.1
grub-efi no longer works:

grub-mkimage: error: relocation 0x4 is not implemented yet.

See:

http://git.savannah.gnu.org/cgit/grub.git/commit/util?id=842c390469e2c2e10b5aa36700324cd3bde25875

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>i [PKG_RELEASE increase]
2018-10-25 16:51:42 +02:00
Jonathan Lancett
9ac7350240 mwlwifi: driver version to 10.3.8.0-20181022
Upgrade 88W8997 firmware to 8.4.0.52.
Removed unnecessary firmware settings.
Added vendor events.
Fixed crash problem when module is removed.
Modified the code to protect tx queues.

Signed-off-by: Jonathan Lancett <j.lancett@ntlworld.com>
[tidy commit message]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-24 17:55:14 +01:00
Hans Dedecker
70315fe144 glibc: update to latest 2.27 commit (BZ #23562, BZ #23275)
77b4b8231e signal: Use correct type for si_band in siginfo_t [BZ #23562]
5bdb6897fc Fix race in pthread_mutex_lock while promoting to PTHREAD_MUTEX_ELISION_NP [BZ #23275]

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-10-23 15:57:51 +02:00
Felix Fietkau
2f9179419c mt76: update to the latest version
d033272 mt76: mt76x0: handle chip specific initval differences
1a2b2dc mt76: usb: fix static tracepoints
11151f4 mt76x0: antenna select corrections
dade109 mt76x0: init: simplify mt76x0_init_mac_registers
3c54612 mt76x0: pci: add missing MODULE_FIRMWARE macro
97e0269 mt76x0: mac: remove mt76x0_mac_set_ampdu_factor
5d8c4bf mt76x0: align mt76x0u and mt76x0e fw version
d4391ae mt76: move mt76x02_mac_set_short_preamble in mt76x02_mac.c
aa6ebf9 mt76: move mt76x02_init_device in mt76x02-lib module
a4a08c3 mt76: move mac beacon routines in mt76x02-lib module
6b69650 mt76: move tx beacon routines in mt76x02-lib module
8486047 mt76x0: pci: add pre_tbtt_tasklet support
acd4c99 mt76: move mt76x02_sw_scan and mt76x02_sw_scan_complete in mt76x02-lib module
2d736cf mt76: move mt76x02_get_txpower in mt76x02_util.c
aa1d6bd mt76: move mt76x02_sta_ps in mt76x02-lib module
e684281 mt76: introduce mt76x02_init_beacon_config routine
c181d97 mt76x0: pci: enable AP support
3b86d99 mt76: move mt76x02_set_tx_ackto in mt76x02-lib module
41d7ef7 mt76x0: update init vals for MT_TX_PROT registers
fe5a149 mt76: move tx protection routines in mt76x02-lib module
5bca2de mt76: move mt76x02_bss_info_changed in mt76x02-lib module
d21a835 mt76: move dfs support in mt76x02-lib module
ba9d424 mt76x0: pci: add DFS support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-23 11:18:06 +02:00
Koen Vandeputte
5f298b95a1 kernel: add missing symbol for target bcm53xx
Fixes: ca88f4153f ("kernel: bump 4.14 to 4.14.77")

Reported-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-23 10:57:02 +02:00
Rafał Miłecki
9b385b2496 bcm53xx: use upstream SPI controller fix
This just moves patch to use 0xx prefix and includes maintainer's s-o-b.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-10-23 09:43:08 +02:00
Koen Vandeputte
bc3d47cd12 kernel: bump 4.14 to 4.14.78
Refreshed all patches.

Remove upstreamed:
- 050-net-emac-fix-fixed-link-setup-for-the-RTL8363SB-swit.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-22 15:28:31 +02:00
Koen Vandeputte
9c42391c0d kernel: bump 4.9 to 4.9.135
Refreshed all patches.

Fixes:
- CVE-2018-10883

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-22 15:28:31 +02:00
Hans Dedecker
59db98d0f2 fstools: update to git HEAD
29e53af fstools: add ntfs support

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-10-21 20:48:36 +02:00
Hauke Mehrtens
9fcfcd49f8 mac80211: hermes-pcmcia: add missing dependency to kmod-pcmcia-core
This fixes a build problem on x86.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-10-21 16:46:16 +02:00
Hauke Mehrtens
e1db49310e linux-firmware: intel: Add iwl 9000 and 9260 firmware
Add the most recent supported firmware file for the Intel 9000 and
9260 wireless chips. The API version 41 is not yet supported by the driver.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-10-20 16:24:29 +02:00
Hauke Mehrtens
10dffe2fa3 linux-firmware: intel: update firmware files for 7265D, 8000C and 8265
Use more recent versions for the Intel wireless chips 7265D, 8000C and 8265.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-10-20 16:24:29 +02:00
Ryan Mounce
4d2613b01a mpc85xx: workaround 4.14 cross compile issue
Regression introduced with 4.10 by 43c9127d94d62a232ed33ed2eab8a08657ce5472

Build will fail if system 'ar' does not support deterministic builds.
e.g. macOS with Xcode toolchain

Appears to be fixed upstream in 4.18 by af3901cbbd3de182aafb8ee553c825c0074df6a2

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-10-20 16:24:29 +02:00
Arthur Skowronek
5f2cb6d7dc tools/pkg-config: pass arguments at the end
Go for openwrt passes pkg-config arguments in the format of

        pkg-config --cflags -- pkg-name

which in turn will be passed down to the real pkg-config as something
like

        pkg-config.real --cflags -- pkg-name --define...

and causes the real pkg-config implementation to missinterpret the given
argument list.

This also helps to fix https://github.com/golang/go/issues/27940

Signed-off-by: Arthur Skowronek <arthur.skowronek@tuta.io>
2018-10-20 16:24:29 +02:00
Yufei Miao
260be8a579 mwlwifi: driver version to 10.3.8.0-20181008
Signed-off-by: Yufei Miao <myf@myf.cloud>
2018-10-20 16:24:29 +02:00
Roman Bazalevskiy
47e7a3904d kernel/modules: Aosong AM2315/AM2320 IIO kernel module support enabled.
Signed-off-by: Roman Bazalevskiy <rvb@rvb.name>
2018-10-20 16:24:29 +02:00
Deng Qingfang
858a8acf3e kernel/modules: add kmod-fou6 package
IPv6 support for Foo-over-UDP tunnel

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-10-20 16:24:23 +02:00
Robert Marko
f6a26f9a20 linux-firmware: Update linux-firmware to 2018-10-18
Kalles ath10k PR was finally merged so update linux-firmware to
include those changes.

This is needed since disabling ath10k-firmware a lot of custom BDF-s
in board-2.bin-s are not available in previously outdated linux-firmware
board-2.bin-s.
This also includes support for boards currently using ipq-wifi and other
WIP ones.

Runtime tested on 8devices Jalapeno.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
fc70276e6c apm821xx: add disk-activity triggers via DT.
The WNDR4700 and the MBL have a dedicated HDD activity LED.
This patch adds the default led triggers to the DTS and
removes the entries in 01_leds.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
1d5d77612f apm821xx: apm82181.dtsi overhaul
- order entries by mmio address where possible

 - switch to lower-case address values

 - comment on BSP u-boot behaviour in regards to
   what it edits and look for

 - annotate irq lines with the help of interrupt-names

 - remove deprecated "device_type" properties
   The pci and network device_type had to stay since
   they are required by the drivers and u-boot.
   the cpu and memory device_types will remain as well
   as they are still part of the DT Spec.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
9ca82c2374 apm821xx: force WNDR4700 console to 115200n8
With the upcoming 4.19 release, the serial console on the
Netgear WNDR4700 would no longer work as it is never really
set and always relied on the kernel's serial code not to
change the baud rate.

On the stock firmware, Netgear forced the console setting
through a custom CONFIG_CMDLINE in their kernel to 115200.
Normally, they should have done it in a different way and
just passed the baudrate through a "console=..." kernel
parameter via the bootargs in the "/chosen" dt node.
But in their default u-boot bootcmd setting, they somehow
forgot to add the "run addtty", so there's no easy way to
pass the baudrate from u-boot to the kernel. So it has
to be forced as otherwise it ends up as 9600 baud.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
68bb91018d apm821xx: set uart compatible to ns16750
The APM821XX/PPC460EX datasheet mentions:
"Register compatibility with 16750 register set"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
92bcd08989 build: remove obsolete -rc kernel testing rewrites
The -rcX "testing" kernels are no longer hosted on
cdn.kernel.org file servers directly in a "testing"
directory. Therefore the logic that tested for "-rc"
can be removed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Linus Walleij
f280bd7fa8 gemini: Fix up image generation
I noticed that the image generator for the Gemini generates
some 10+ MB files for the second (application) partition.
This is just wrong. The first 6144K partition named initramfs
easily fits OpenWRTs squashfs,jffs2 overlayed partitions
with nice headroom for storing configuration files.

Generate a blank partition for the hddapp.tgz file and delete
it after generating the firmware image - when performing
updates manually you just want the "rd.z" file around
anyways.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-20 16:13:39 +02:00
Linus Walleij
10ec966f7b gemini: Break out USB to packages
This creates a new kernel package for the fotg210 host
controller and uses that with the gemini to shrink the
kernel. The SQ201 needs the USB2 PCI package as well.

The build system required me to make kernel_oldconfig
beofore it would build without errors so some minor
unrelated Kconfig entries are changed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-20 16:13:39 +02:00
Baptiste Jonglez
b2c68ceea7 kernel: Add support for Winbond w25q128jv SPI NOR flash
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:

- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G

and probably other Mikrotik boards need this patch as well.

The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/

Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
2018-10-20 16:13:39 +02:00
Daniel Engberg
d27d87c910 toolchain/musl: Don't override optimization set by upstream
Don't override optimization set by upstream.
Provides a speed increase for internal (library), malloc and string
operations in musl.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[add : to PKG_RELEASE release variable for consistency]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-20 14:22:56 +01:00
Kevin Darbyshire-Bryant
6c4d3d705a dnsmasq: bump to v2.80
dnsmasq v2.80 release

Change from rc1:

91421cb Fix compiler warning.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-19 17:36:02 +01:00
Koen Vandeputte
ca88f4153f kernel: bump 4.14 to 4.14.77
Refreshed all patches.

Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch

New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-19 10:01:57 +02:00
Koen Vandeputte
6d682d82b0 kernel: bump 4.9 to 4.9.134
Refreshed all patches.

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-19 10:01:57 +02:00
Hans Dedecker
15a59e3e08 iproute2: install ip-tiny and ip-full in /usr/libexec
Install the ip-tiny and ip-full variants in /usr/libexec as the suffixed
ip variants are not meant to be called directly

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-10-18 17:15:51 +02:00
Felix Fietkau
a91d82303c mt76: update to the latest version
b51337a mt76: clean up unused leftover EXPORT_SYMBOLs
383b228 mt76x0: reduce duplication in setting rf bandwidth parameters
a1a4528 mt76: mt76x0: handle chip specific initval differences
f473340 mt76: usb: fix static tracepoints
3a975b4 mt76x0: antenna select corrections
37c1150 mt76x0: init: simplify mt76x0_init_mac_registers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-18 16:29:25 +02:00
Jason A. Donenfeld
4653818dab wireguard: bump to 0.0.20181018
ba2ab5d version: bump snapshot
5f59c76 tools: wg-quick: wait for interface to disappear on freebsd
ac7e7a3 tools: don't fail if a netlink interface dump is inconsistent
8432585 main: get rid of unloaded debug message
139e57c tools: compile on gnu99
d65817c tools: use libc's endianness macro if no compiler macro
f985de2 global: give if statements brackets and other cleanups
b3a5d8a main: change module description
296d505 device: use textual error labels always
8bde328 allowedips: swap endianness early on
a650d49 timers: avoid using control statements in macro
db4dd93 allowedips: remove control statement from macro by rewriting
780a597 global: more nits
06b1236 global: rename struct wireguard_ to struct wg_
205dd46 netlink: do not stuff index into nla type
2c6b57b qemu: kill after 20 minutes
6f2953d compat: look in Kbuild and Makefile since they differ based on arch
a93d7e4 create-patch: blacklist instead of whitelist
8d53657 global: prefix functions used in callbacks with wg_
123f85c compat: don't output for grep errors

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2018-10-18 08:55:01 +02:00
Fabio Bettoni
ddc11c3932 ar71xx/ath79: fix mtd corruption
In commit fec8fe8069 ("kernel: bump 4.9 to 4.9.116") [1], the following patch for removed:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch

This patch contained fixes for both write and erase functions.

While the chip-detects for erase got fixed upstream [2],
some modifications are still required, even with the fixes applied.

While at it, also apply the same fix for target ath79,
which suffers the same issue.

Not doing so results in following errors seen:

Collected errors:
 * pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error.
 * opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain!
 * opkg_install_cmd: Cannot install package luci-ssl.
 * opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error.

[    0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.423476] mount_root: switching to jffs2 overlay
[  270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962
[  270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe

Fixes: fec8fe8069 ("kernel: bump 4.9 to 4.9.116")
Signed-off-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-17 18:55:37 +02:00
Koen Vandeputte
5f24933309 ar71xx: Move some targets to tiny
Recent changes on ar71xx (switch to 4.14, memory compaction, ...) cause
an increase in kernel size, making it too big for some devices.

Move these devices to the tiny target, where kernel symbols and
optimization for speed are disabled, reducing the kernel size.

Devices:
- EnGenius ENS202EXT
- OCEDO Koala

Compile-tested targets:

- ar71xx->generic->default
- ar71xx->smallFlash->Default

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-17 18:02:16 +02:00
Hans Dedecker
db6f9d5598 netifd: update to latest git HEAD
841b5d1 system-linux: enable by default ignore encaplimit for grev6 tunnels
125cbee system-linux: fix a typo in gre tunnel data parsing logic

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-10-17 11:18:30 +02:00
Hans Dedecker
3d015e971f gre: make encaplimit support configurable
Make inclusion of the destination option header containing the tunnel
encapsulation limit configurable for IPv6 GRE packets.
Setting the uci parameter encaplimit to ignore; allows to disable the
insertion of the destination option header in the IPv6 GRE packets.
Otherwise the tunnel encapsulation limit value can be set to a value
from 0 till 255 by setting the encaplimit uci parameter accordingly.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-10-17 11:18:20 +02:00
Rosen Penev
622176262d tools/xz: Add PKG_CPE_ID for proper CVE tracking
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-10-16 19:17:36 +01:00
Rosen Penev
74a5c619dc tools/libressl: Add PKG_CPE_ID for proper CVE tracking
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-10-16 19:16:28 +01:00
Mathias Kresin
80c61c161a treewide: use wpad-basic for not small flash targets
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-16 15:07:41 +01:00