Change lan and it's LED to eth0
It's broken since c7c807cb8c
where I changed the dts but forgot to change default configurations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
1. Swap eth0/eth1
Both devices are using AR9331, the builtin switch on AR9331 is
connected to gmac1 and gmac1 is named as eth1 in ath79.
PS: gmac1 is eth0 and gmac0 is eth1 in ar71xx because of the
reversed initialization order.
2. Fix the incorrect compatible string in dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
phy-handle is used to poll link status. They are useless when
we need fixed-link on these interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Jonas Gorski commented on the previous patch:
|This is actually the wrong fix and papers over an issue in one of our
|local patches.
|
|We intentionally allow regmap to be built as a module, see
|
|/target/linux/generic/hack-4.14/259-regmap_dynamic.patch
|[...]
|[The regulator code] optionally supports regmap thanks to the stubs
|provided if regmap is disabled - which breaks if you compile regmap
|as a module.
In order to mitigate this issue, this patch reverts the previous patch
and replaces the existing IS_ENABLED(CONFIG_REGMAP) with
IS_REACHABLE(CONFIG_REGMAP). This solves this particular issue as the
regulator code will now automatically fallback to the regmap stubs in
case the kmod-regmap module is enabled, but nothing else sets
CONFIG_REGMAP=y.
Note: There's still a potential issue that this patch doesn't solve:
If someone ever wants to make a OpenWrt kernel package for a
regulator module that requires the REGMAP feature for a target that
doesn't set CONFIG_REGMAP=y but has CONFIG_REGULATOR=y, the resulting
kmod-regulator-xyz package will not work on the target.
Luckily, there aren't any in-tree OpenWrt kernel module packages for
regulators at the moment. On the bright side: regmap is a critical
part nowadays and all new and upcoming architectures require it by
default. This will likely only ever be a problem for legacy targets
and devices that cannot afford to enable REGMAP.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
Fixes: d00913d121 ("kernel: modules: fix kmod-regmap")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)
when port4 setup to work as gmac mode, dts like:
&gsw {
mediatek,port4 = "gmac";
};
we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0
before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY
after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.
Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
This really simplifies debugging, if a package is not found or a feed is
not reachable, a proper stderr is printed. Currently it would only say
`_call_manifest` failed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Sysupgrade shouldn't proceed, if the backup of the configuration
fails because tar (or gzip) exit with a non-zero code.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
Use Time::HiRes when available and fallback to raw syscall interface
when not. If that fails too, simply report 0, 0 as real time.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Replace the GNU time program invocation with a simple Perl script reporting
the timing values. Since we require Perl anyway for the build system, we can
as well use that instead of requiring a random GNU utility rarely installed
by default.
Fixes: ff6e62b288 ("build: log time taken by each packages/steps")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.
Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.
Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.
Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.
If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.
Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.
Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.
Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.
gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.
Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
Revert 290c54473e ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.
Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.
The correct MAC adress increments for this board are:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
Fixes: FS#408
Signed-off-by: Mathias Kresin <dev@kresin.me>
Changelog taken from the version announcement
> == Changes ==
>
> * chacha20poly1305: selftest: split up test vector constants
>
> The test vectors are encoded as long strings -- really long strings -- and
> apparently RFC821 doesn't like lines longer than 998.
> https://cr.yp.to/smtp/message.html
>
> * queueing: keep reference to peer after setting atomic state bit
>
> This fixes a regression introduced when preparing the LKML submission.
>
> * allowedips: prevent double read in kref
> * allowedips: avoid window of disappeared peer
> * hashtables: document immediate zeroing semantics
> * peer: ensure resources are freed when creation fails
> * queueing: document double-adding and reference conditions
> * queueing: ensure strictly ordered loads and stores
> * cookie: returned keypair might disappear if rcu lock not held
> * noise: free peer references on failure
> * peer: ensure destruction doesn't race
>
> Various fixes, as well as lots of code comment documentation, for a
> small variety of the less obvious aspects of object lifecycles,
> focused on correctness.
>
> * allowedips: free root inside of RCU callback
> * allowedips: use different macro names so as to avoid confusion
>
> These incorporate two suggestions from LKML.
>
> This snapshot contains commits from: Jason A. Donenfeld and Jann Horn.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The Linux headers on arm64 architectures contain references to common
arch/arm/ headers which were not bundled by the SDK so far.
Check if we're packing the SDK for an arm64 target and if we do, also
include arch/arm headers as well.
Fixes FS#1725.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch makes sch_cake's gso/gro splitting configurable
from userspace.
To disable breaking apart superpackets in sch_cake:
tc qdisc replace dev whatever root cake no-split-gso
to enable:
tc qdisc replace dev whatever root cake split-gso
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Dave Taht <dave.taht@gmail.com>
[pulled from netdev list - no API/ABI change]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Follow upstream kernel patch that restores always splitting gso packets
by default whilst making the option configurable from (tc) userspace.
No ABI/API change
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes the annoying 'feature' were TTL was set to "1" by default ..
Users had to specify -T manually to test outside the own network.
2.0.12 change set (as of June 25th 2018)
o Change the unicast TTL default value from 1 to the system default (to be compatable with previous versions.) Multicast still defaults to 1.
o adpative formatting bug fix: crash occurs when values exceed 1 Tera. Add support for Tera and Peta and eliminate the potential crash condition
o configure default compile to include isochronous support (use configure --disable-isochronous to remove support)
o replace 2.0.11's --vary-load option with a more general -b option to include <mean>,<stdev>, e.g. -b 100m,40m, which will pull from a log normal distribution every 0.1 seconds
o fixes for windows cross compile (using mingw32)
o compile flags of -fPIE for android
o configure --enable-checkprograms to compile ancillary binaries used to test things such as delay, isoch, pdf generation
o compile tests when trying to use 64b seq numbers on a 32b platform
o Fix GCC ver 8 warnings
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
It seems to have been missed when the patch was accepted.
Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The integrated SoC wifi will likely never be supported, and if,
it will go through DT with the sprom contents there.
Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
GDB 8.1.1 brings the following fixes and enhancements over GDB 8.1:
* PR gdb/22824 (misleading description of new rbreak Python function in GDB 8.1 NEWS file)
* PR gdb/22849 (ctrl-c doesn't work in extended-remote)
* PR gdb/22907 ([Regression] gdbserver doesn't work with filename-only binaries)
* PR gdb/23028 (inconsistent disassemble of vcvtpd2dq)
* PR gdb/23053 (Fix -D_GLIBCXX_DEBUG gdb-add-index regression)
* PR gdb/23127 ([AArch64] GDB cannot be used for debugging software that uses high Virtual Addresses)
* PR server/23158 (gdbserver no longer functional on Windows)
* PR breakpoints/23210 ([8.1/8.2 Regression] Bogus Breakpoint address adjusted from 0xf7fe7dd3 to 0xfffffffff7fe7dd3)
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
GDB 8.1.1 brings the following fixes and enhancements over GDB 8.1:
* PR gdb/22824 (misleading description of new rbreak Python function in GDB 8.1 NEWS file)
* PR gdb/22849 (ctrl-c doesn't work in extended-remote)
* PR gdb/22907 ([Regression] gdbserver doesn't work with filename-only binaries)
* PR gdb/23028 (inconsistent disassemble of vcvtpd2dq)
* PR gdb/23053 (Fix -D_GLIBCXX_DEBUG gdb-add-index regression)
* PR gdb/23127 ([AArch64] GDB cannot be used for debugging software that uses high Virtual Addresses)
* PR server/23158 (gdbserver no longer functional on Windows)
* PR breakpoints/23210 ([8.1/8.2 Regression] Bogus Breakpoint address adjusted from 0xf7fe7dd3 to 0xfffffffff7fe7dd3)
GDB 8.1 includes the following changes and enhancements:
* Breakpoints on C++ functions are now set on all scopes by default
("wild" matching);
* Support for inserting breakpoints on functions marked with C++ ABI tags;
* Target floating-point arithmetic emulation during expression evaluation
(requires MPFR 3.1 or later);
* Various Python Scripting enhancements;
* Improved Rust support; in particular, Trait objects can now be inspected
when debugging Rust code;
* GDB no longer makes assumptions about the type of symbols without
debugging information to avoid producing erroneous and often confusing
results;
* The 'enable' and 'disable' commands now accept a range of breakpoint
locations;
* New 'starti' command to start the program at the first instruction;
* New 'rbreak' command to insert a number of breakpoints via a regular
expression pattern (requires Python);
* The 'ptype' command now supports printing the offset and size of
the fields in a struct;
* The 'gcore' command now supports dumping all the memory mappings
('-a' command-line option);
* New shortcuts for TUI Single-Key mode: 'i' for stepi, and 'o' for nexti;
* GDBserver enhancements:
** Support for transmitting environment variables to GDBserver;
** Support for starting inferior processes with a specified initial
working directory;
** On Unix systems, support for globbing expansion and variable
substitution of inferior command-line arguments;
* Various completion enhancements;
* The command used to compile and inject code with the 'compile' command
is now configurable;
* New '--readnever' command-line option to speed the GDB startup when
debugging information is not needed;
* Support for the following new native configurations:
** FreeBSD/aarch64 (aarch64*-*-freebsd*);
** FreeBSD/arm (arm*-*-freebsd*);
* Support for the following new targets:
** FreeBSD/aarch64 (aarch64*-*-freebsd*);
** FreeBSD/arm (arm*-*-freebsd*);
** OpenRISC ELF (or1k*-*-elf)
* Removed support for the following targets and native configurations:
** Solaris2/x86 (i?86-*-solaris2.[0-9]);
** Solaris2/sparc (sparc*-*-solaris2.[0-9]);
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
1) Add comments so it's clear why we did things; this may prevent
someone (e.g. me) from sinking time into fixing things that
aren't broken and/or were done for reason.
2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0.
3) Cosmetic reording of some code (tested) that makes the defintion
more clear.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
The CR3000 stock firmware is now irrelevant as it required a now defunct
cloud service. Therefore only build images that use the entire flash
(overwriting stock firwmare-specific partitions that no longer matter),
previously called 'nocloud' images.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
