Commit graph

43 commits

Author SHA1 Message Date
John Crispin
f16f310306 lantiq: add default switch setup to td8970
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42544
2014-09-15 10:18:37 +00:00
John Crispin
5f71dbb005 lantiq: improve ARV7519RW22 support
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 42180
2014-08-18 13:08:56 +00:00
John Crispin
e2915c6981 lantiq: add support for /tmp/sysinfo
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41472
2014-07-02 16:33:11 +00:00
John Crispin
390e856cb2 lantiq: more vdsl related cleanups
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 40460
2014-04-11 20:40:24 +00:00
John Crispin
eebc673f1e lantiq: move the dsl-modem config to network.@dsl-modem[-1]
make sure uci_defaults generates a proper uci config for the v/adsl modem

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 40439
2014-04-10 08:14:33 +00:00
John Crispin
15139d468c lantiq: BT Home Hub 2B support - userspace
Basic userspace configuration for BT Home Hub 2B

Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>

SVN-Revision: 40371
2014-04-03 14:26:58 +00:00
John Crispin
e36568e74b lntiq: add support for Astoria ARV7519RW.
These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.

Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>

SVN-Revision: 40329
2014-03-30 10:02:30 +00:00
John Crispin
112059073e lantiq: fix initial VLAN conf for P2601HNFX
Signed-off-by: Antonios Vamporakis <ant@area128.com>

SVN-Revision: 40321
2014-03-30 09:16:23 +00:00
John Crispin
e733242a23 lantiq: add support for Arcadyan ARV7519PW
This patch adds almost full support for this board.

- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port

Signed-off-by: Antonios Vamporakis <ant@area128.com>

SVN-Revision: 40319
2014-03-30 09:16:15 +00:00
John Crispin
9531390aad lantiq: add support for ZyXEL P2812HNUFX
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.

Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 40317
2014-03-30 09:16:06 +00:00
John Crispin
053d596297 lantiq: Add support for Astoria ARV7510PW22
This board is pretty similar to ARV752DPW22.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 39303
2014-01-15 19:16:51 +00:00
John Crispin
f58b424c9e lantiq: improve Arcadyan ARV4510PW support
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is
severely lacking. This patch brings it up-to-date.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 39230
2014-01-12 12:07:07 +00:00
John Crispin
000cefd85e lantiq: DGN3500 fixups
Just fixing up a few things for the Netgear DGN3500.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>

SVN-Revision: 38733
2013-11-11 13:15:08 +00:00
John Crispin
7ee1546ca3 lantiq: fix TDW8970 lan/wan mac
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38677
2013-11-07 12:46:24 +00:00
John Crispin
f198adc030 lantiq: Fix ar8216 switch configuration for WBMR-HP-G300H devices
The switch is renamed to "switch0" in newer (3.10) linux kernels.
Configure the switch using vlans by default and only configure
the physical switch ports that are present.

Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38673
2013-11-07 12:46:08 +00:00
Luka Perkov
3b33adeb99 lantiq: add support for ZyXEL P2601HNFX
SVN-Revision: 38049
2013-09-19 00:50:46 +00:00
Luka Perkov
7d2c5682b9 lantiq: add support for ZTE H201L
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 38048
2013-09-19 00:50:44 +00:00
Luka Perkov
27fa640548 lantiq: add (incomplete) support for Aztech GR7000
*) can not connect to switch chip
*) only one usb port is working
*) wifi is not working

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 37712
2013-08-06 10:17:16 +00:00
John Crispin
288adb6634 lantiq: several a803 related fixes
based on work from Matti Laasko that he posted in the wiki

Signed-off-by: John Crispin <blogic@openwrt.or

SVN-Revision: 37704
2013-08-05 10:42:00 +00:00
John Crispin
b4c722267e lantiq: fix VG3503J ethernet/gphy led support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 37634
2013-08-01 14:30:40 +00:00
John Crispin
32f7ae4ce6 lantiq: add a hook to make leds work on the secondary usb bus
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 37538
2013-07-25 20:29:01 +00:00
John Crispin
c2b1e9eeef lantiq: Fix ar8216 switch configuration
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 36782
2013-05-30 16:00:59 +00:00
John Crispin
090a75447b lantiq: DGN3500 support
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>

SVN-Revision: 36781
2013-05-30 16:00:50 +00:00
John Crispin
b585923cc9 lantiq: fix LED-handling oversights
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>

SVN-Revision: 36777
2013-05-30 16:00:15 +00:00
John Crispin
b42a173664 lantiq: make leds and network work on VG3503J
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 36445
2013-04-25 19:03:41 +00:00
Steven Barth
ea94d66b0f Adapt default network configuration for IPv6
SVN-Revision: 36278
2013-04-09 08:03:08 +00:00
John Crispin
e3a6ea65e1 add support for AudioCodes AC-252
user-space support for extracting the EEPROM for the RaLink WiFi is still
missing. Besides this, it's all working.

Signed-off-by: Daniel Golle <dgolle@allnet.de>

SVN-Revision: 35990
2013-03-12 13:52:54 +00:00
Jo-Philipp Wich
3a2cccda2e all targets: use numerically prefixed uci-defaults file names to better control order of execution
SVN-Revision: 35217
2013-01-18 12:42:53 +00:00
John Crispin
90a3761b0b default switch setup for WBMR
SVN-Revision: 34838
2012-12-21 20:04:12 +00:00
John Crispin
9818a1f00b adds script to set wps info on boards with a wps button
SVN-Revision: 34836
2012-12-21 20:03:59 +00:00
John Crispin
687920ba3e minor basefiles fixes
SVN-Revision: 34790
2012-12-19 15:17:42 +00:00
John Crispin
1dece11487 cleanup basefiles
SVN-Revision: 34698
2012-12-15 02:01:00 +00:00
Luka Perkov
4c76b3635b lantiq: fix sx76x default uci network configuration
SVN-Revision: 33324
2012-09-06 00:09:46 +00:00
Luka Perkov
7f00e5ffc6 uboot-envtools: update to 2012.04.01
SVN-Revision: 32051
2012-06-04 21:55:49 +00:00
Gabor Juhos
ff74305623 lantiq: use the generic uci-default functions for initial LED setup
SVN-Revision: 31995
2012-05-29 16:39:21 +00:00
Mirko Vogt
87cdc0dd5b change /etc/config/network according to actual VLAN config to enable LAN port 4 on the ARV4520PW board
The VLAN mapping on the ARV4520PW board is the following:

port on Router: | VLAN in software:
LAN 1           | 3
LAN 2           | 2
LAN 3           | 1
LAN 4           | 0
DSL             | 4

So LAN4 is not VLAN4 but VLAN0 (VLAN4 is DSL port) -> set "3 2 1 0 5t" as default switch config.

SVN-Revision: 31391
2012-04-21 08:07:21 +00:00
John Crispin
f27c030141 update /etc/uci-defaults/*
SVN-Revision: 31062
2012-03-25 08:50:30 +00:00
John Crispin
1a71f07d00 generate uboot environment data in target
With this patch it is possible to generate uboot environment config file
inside lantiq target. Currently it is only supporting GIGASX76X board.

uboot environment config is used by fw_printenv fw_setenv tools.

Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>

SVN-Revision: 30537
2012-02-14 19:07:11 +00:00
John Crispin
976d3eb854 add annex selection support to ltq_dsl package
SVN-Revision: 30518
2012-02-14 15:05:49 +00:00
John Crispin
49eb3fd845 gigaset 76x
* fixes leds
* adds all leds found on the sx763 board
* removes board_config from flash layout because wireless data is stored in kernel (ath5k)
* fix button handling

Signed-off-by: Luka Perkov <openwrt@lukaperkov.net>

SVN-Revision: 29763
2012-01-17 12:10:35 +00:00
John Crispin
4982ca983c lantiq: * fixes ath5k eeprom handling * fixes sx76x * adds sx76x to userland api * minor style cleanups
Signed-of-by: Andrej Vlašić <andrej.vlasic0@gmail.com>

SVN-Revision: 29292
2011-11-22 18:50:51 +00:00
John Crispin
bbe96f13a6 lantiq: add runtime generation of /etc/config/network
SVN-Revision: 29161
2011-11-15 18:21:00 +00:00
John Crispin
a8797d0de6 lantiq: add uci-defaults code for handling leds
SVN-Revision: 29004
2011-11-12 23:40:21 +00:00