Add rut5xx GPIO PIN selection to om-package startup script.
Testet on a RUT500 device, the timeout value of the hardware watchdog
is about 280 sec.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
[split into two commits, bump PKG_RELEASE]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
93abe6f config: fix invalid hoplimit in RA message
2ae08d1 config: fix invalid retranstime in RA message
0005cb4 config: fix invalid reachabletime in RA message
5683dd2 config: limit ra_mtu to 65535
f8d40a5 router: fix interface mtu read error
f8f4b87 config: limit ra_retranstime to 60000
a2d8bf6 dhcpv4: display two hex digits per octet in syslog
a9e9bc4 config: make RA retransTime configurable via uci
2cb6b48 config: make RA reachableTime configurable via uci
e4504db config: make RA curHopLimit configurable via uci
9dd5316 config: make RA mtu configurable via UCI
29cb2ff config: fix dhcpv4 server being started
0ef74ec ndp.c: add switch/case fallthrough comments
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
uci_set_leds_ataport() allows to set a led to show activity
on a specific (s)ata port, which is needed for devices that have
a Sata led for each sata port.
The led trigger is from the 834-ledtrig-libata.patch LEDE kernel patch.
uci_set_leds_usbhost() allows to set a led to show total usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
create a function with code common to all led functions,
create another function with code common to functions setting
a simple led trigger, restore alphabetical order in function names.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Gracefully handle cases where the to-be-created wireless interface already
exists on the system which might commonly happen with non-multi-SSID capable
wireless drivers.
This fixes commit 8301e61365 which caused
previously ignored "Too many open files in system (-23)" errors to fail the
wireless setup procedure.
With the updated approach we'll still try recreating the vif after one
second if the first attempt to do so failed with ENFILE but we will now
consider the operation successfull if a second attempt still yields ENFILE
with the requested ifname already existing on the system.
Fixes FS#664, FS#704.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
One of the latest mac80211 updates added sanity checks, requiring the
beacon intervals of all VIFs of the same radio to match. This often broke
AP+11s setups, as these modes use different default intervals, at least in
some configurations (observed on ath9k).
Instead of relying on driver or hostapd defaults, change the scripts to
always explicitly set the beacon interval, defaulting to 100. This also
applies the beacon interval to 11s interfaces, which had been forgotten
before. VIF-specific beacon_int setting is removed from hostapd.sh.
Fixes FS#619.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
None of the variables in this "local" declaration are actually set in
wpa_supplicant_add_network().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some external toolchains may be configured to enable OpenMP. Provide a
package for these libraries which can be used by other packages.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the necessary changes to CMakeLists.txt to search zlib.h. Fixes
build issues with external toolchains that don't have STAGING_DIR in the
default search path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Toolchain built for ARCv1 (read for ARC700 cores) by default has
disabled atomic ops (-mno-atomic). When we build Linux kernel for ARC770
which has LL/SC instructions and thus may handle normally atomic ops we
explicitly add "-matomic" in CFLAGS. But since user-space perf utility has
no way to extract CPU config options from Kconfig/defconfig it uses
compiler default settings.
In case of ARCv2 (read ARC HS38) atomics are enabled by default and so
perf builds perfectly fine thus reenabling perf for ARC HS38 (actually
for non-ARC700 targets).
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
This patch adds the interface-name option for each dhcp config
in /etc/config/dhcp.
With the interface_name option users can define a DNS name for each dhcp section
that will be resolved by dnsmasq with the underlaying interface address.
For example:
config dhcp 'lan'
option interface 'lan'
...
list interface_name 'home.lan'
...
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If there's a TFTP root directory configured, create it with mkdir -p
(which does not throw an error if the folder exists already)
before starting dnsmasq. This is useful for TFTP roots in /tmp, for example.
Originally submitted by nfw user aka Nathaniel Wesley Filardo
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Setting legacy_rates to 0 disables 802.11b data rates.
Setting legacy_rates to 1 enables 802.11b data rates. (Default)
The basic_rate option and supported_rates option are filtered based on this.
The rationale for the change, stronger now than in 2014, can be found in:
https://mentor.ieee.org/802.11/dcn/14/11-14-0099-00-000m-renewing-2-4ghz-band.pptx
The balance of equities between compatibility with b clients and the
detriment to the 2.4 GHz ecosystem as a whole strongly favors disabling b
rates by default.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, defaults change]
When sta is configured, hostapd receives 'stop' and 'update' command from
wpa_supplicant. In the update command, hostapd gets sta parameters with
which it configures ap.
Problem is, with the default wireless configuration:
mode:11g freq:2.4GHz channel:1
If sta is connected to 5GHz network, then ap does not work. Ideally with
340-reload_freq_change.patch hostapd should reload the frequency changes
and start ap in 5GHz, but ap becomes invisible in the network.
This issue can be reproduced with following /etc/config/wireless:
config wifi-device radio0
option type mac80211
option channel 1
option hwmode 11g
option path 'virtual/uccp420/uccwlan'
option htmode 'none'
config wifi-iface 'ap'
option device 'radio0'
option encryption 'none'
option mode 'ap'
option network 'ap'
option ssid 'MyTestNet'
option encryption none
config wifi-iface 'sta'
option device radio0
option network sta
option mode sta
option ssid TestNet-5G
option encryption psk2
option key 12345
This change updates current_mode structure based on configured hw_mode
received from wpa_supplicant. Also prepare rates table after frequency
selection.
Signed-off-by: Abhilash Tuse <Abhilash.Tuse@imgtec.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup, patch refresh]
Commit 2036ae4 (base-files: support hostname and ntp servers through board.d)
was supposed to implement these procedures but lacked the required changes
to uci-defaults.sh.
Add the missing procedures now to fix config generation on targets relying
on hostname or NTP server presetting.
Fixes FS#754.
Reported-by: Cristian Morales Vega <cristian@samknows.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When busybox customisation is enabled, we should depend on config
symbols CONFIG_BUSYBOX_CONFIG_xxx to form alternatives specs
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
A number of small tweaks & improvements on the way to a final release.
Most notable:
Improve DHCPv4 address-in-use check.
Remove the recently introduced RFC-6842 (Client-ids in DHCP replies)
support as it turns out some clients are getting upset.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Changes since last version
546bc72 pkg: alternatives support
7a96972 libbb: xreadlink: fix memory leak on failure case
3f13edd pkg_run_script: use pkg->dest in half installed case
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
arc-2016.09 is the most recent toolchain for ARC cores and
it is based on top of upstream Binutils 2.27 and GCC 6.2.1.
With updated major version of GCC we copied all GCC 6.x patches
for ARC as well as Bintils 2.27 patches.
Note that toochain sports ARCv4 ABI and so must be used
with 4.8+ Linux kernels. Even though it will build v4.4 kernel
perfectly fine on attempt to run user-space apps they won't
work with older kernel. That said previuosly sent RFC patches with
Linux kernel update are required:
[1] https://patchwork.ozlabs.org/patch/726686/
[2] https://patchwork.ozlabs.org/patch/726687/
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Even it's unknown if it's booting with thumb, because the lack of hardware.
Enable it for now, so the build succeed, because without thumb it can not fit
into spl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
9268ca6 ndp: don't trigger IPv6 ping when neighbor entry is invalid
2b3355f ndp: fix adding proxy neighbor entries
7dff5b4 ndp: fix wrong interface name in syslog message
a54afb5 dhcpv6-ia: Fix segfault when writing DHCPv4 leases in state file
c0e9dbf ubus: don't segfault when there're no leases
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Configuring dhcp_option as an option does not allow the usage of white
spaces in the option value; fix this by supporting dhcp_option as a list
config while still supporting the option config to maintain backwards
compatibility
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
When invoking "nslookup_lede" with a domain argument and without explicit
query type, issue both A and AAAA queries and display the resulting IP
addresses in a numbered list style, similar to how the old BusyBox nslookup
used to output the records.
This is required for compatibility with certain scripts.
Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The ":*" optstring syntax was only recently introduced with BusyBox v1.26,
older versions need a corresponding hint in the "opt_complementary" variable
to denote flag values that should be stored as llist entries.
Add the required opt_complementary entry to fix random SIGBUS, SIGILL or
SIGSEGV related crashes on BusyBox 1.25.x when attempting to use the "-q"
flag of the "nslookup_lede" applet.
Ref: https://forum.lede-project.org/t/nslookup-ipv6-in-lede-17-01-1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Install procd interface triggers only for interfaces which are enabled
so dropbear instances running on (an) enabled interface(s) are not
restarted due to an interface trigger of an interface which is disabled.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Merged upstream in https://patchwork.kernel.org/patch/9572541/, this
patch fixes the OTP offset used by the AR934x and AR955X to properly
enable reading from the OTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Update mdadm to 4.0
Remove 000-compile.patch as it's fixed upstream
Refresh patches
Add mdadm.h-Undefine-dprintf-before-redefining.patch
Source: http://git.openembedded.org/openembedded-core/tree/meta/recipes-extended/mdadm/files
Add RAID 0,1 and 10 as depends to make mdadm usable.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Based on a patch by Alexandru Ardelean.
netifd ubus reload call returns the actual reload error status;
return error status as well in reload_service
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
11cb9cf ubus: add interface method to trigger renew event
4375d1b system-linux: allow "throw" route type
5fbd904 netifd: propagate error code on netifd_reload()
6e0acec interface-ip: fix device name for IPv6 link-local DNS server
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The beagleboard doesn't boot with Thumb enabled, but without Thumb the
SPL (first stage bootloader) is too big to fit into SRAM.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Do as the vendor driver does -- however, some devices apparently
patched support for external PA into the driver similar to how it was
done on Rt3352, using EEPROM_NIC_CONF1 rather than EEPROM_NIC_CONF2,
hence we check for both fields. Somehow the vendor driver also no
longer offers the option of only one of the TX paths having an external
PA (which was probably to weird to ever be implemented in practise,
though it doesn't seem like a particularly bad idea to me). Do the same
in rt2x00 and enable support for external PA on both TX paths whenever
it is set for TX0 in EEPROM.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import change to make external PA capability consistent with the
vendor driver instead of having the logic inverted.
While at it, apply patches in the same order as they got merged
upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The dep for the nftables support was wrong, if someone actually enable
that option gain a compilation error. This fix this problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Protect any IPv6 related with appropriate guards to fix compilation with
disabled IPv6 support in Busybox.
Fixes#728.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
update RF register 47 and 54 values according to vendor driver
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: moved changes into a separate patch]
Use register values from init LNA function instead of the ones from
restore LNA function. Apply register values based on rx path
configuration.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: moved changes into a separate patch]
Make brcmfmac depend on !TARGET_uml.
Technically, brcmfmac could be built for uml because only SDIO support
won't work on that target. However, selectively avoiding the dependency
propagation of !TARGET_uml from kmod-mmc to avoid including a reference
to BRCMFMAC_SDIO doesn't work.
In practice, brcmfmac is completely useless on uml, so let's just
disable it there.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
minor/cosmetic: fixes the following misleading message:
root@box:~ /etc/init.d/dnsmasq restart
sh: out of range
Signed-off-by: Bastian Bittorf <bb@npl.de>
Since the LEDE nslookup applet is already specific to LEDE, move the
libresolv detection into the busybox Makefile that LEDE uses.
This fixes builds with external toolchains that don't automatically
search for headers and/or libraries without being told so.
Fixes: de5b8e5d2f ("busybox: add musl compatible nslookup replacement")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Apply the !UML dependency to both the symbol and the DEPENDS so there is
no recursive dependency anymore.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
binutils 2.27 checks if the target compiler supports -Wstack-
usage=262144, and also uses this setting for the host compiler. If the
host compiler is gcc < 4.9 binutils build will fail. This backports 2
commits which are fixing this problem for binutils 2.28.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was also working before, with a slightly
different semantic.
[ Original semantic ]
If no reload hooks was implemented, the default one would
kick in, it would return fail, and restart would happen.
This would happen also in the case where a reload hook
would be implemented, it would fail, and it would restart
the service.
[ New semantic ]
The default reload hook calls restart.
Services can implement their own reload.
If reload fails, then the '/etc/init.d/<service> reload'
would return a non-zero code, and the caller can choose
a way to handle this.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Update OpenVPN to 2.4.1
Remove 200-small_build_enable_occ.patch as it's included upstream.
Refresh patches
Add mirror and switch to HTTPS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Add an alternative nslookup applet implementation which is compatible with
musl libc wrt. name server selection and which supports a number of additional
features such as query type selection.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit f4e312ddf8 adds libnetlink to
staging dir but did not add the header files libgenl.h and ll_map.h
which define functions belonging to libnetlink lib
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Similar to odhcpd, allow using ISC DHCPd instead of dnsmasq.
Disable DHCP and/or DHCP6 in case ISC DHCP is present and
enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Don't setup the default led pin if the ath9k GPIO controller is used
via device tree to prevent collision. In case any of the pins exposed
by the ath9k is used, the phyNtpt trigger needs to be set in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In case that the atheros device tree binding is used, enable access to
the GPIO chip only if the gpio-controller device tree parameter is used
for the ath9k node.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Unset the default LED gpio pin if the same gpio pin is used by a LED
defined via platform LED. This prevents that the default led trigger
gets assigned to this LED and the GPIO value gets changed on
wifi up/down in case the led is not used for signaling the wifi state.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.
Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.
Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Update to latest Git in order to import the following fixes:
1d0263b check_data_file_clashes_change: remove duplicated offline root in paths
a00a6a9 buildReplaces: do not add duplicated replacees
9fbedd8 opkg: compare-versions doesn't need any state
45b54f6 opkg_cmd: fix segmentation fault in opkg_compare_versions_cmd()
93de62b opkg_cmd: fix return of opkg compare-versions
51275a8 pkg_src_list_push: remove unused function
947d3d4 pkg_src_list_pop: remove unused function
980cfb2 str_list_push: remove unused function
52c31c1 str_list_prev: remove unused function
7d24212 str_list_last: remove unused function
48142a3 conffile_list_pop: remove unused function
46c5de5 pkg_dest_list_push: remove unused functions
368bb62 nv_pair_list_prev: remove unused function
2985c00 nv_pair_list_last: remove unused function
f5082ac conffile_list_pop: remove unused function
89bf8b9 conffile_list_push: remove unused function
23d31fb active_list_sort: remove unused function
7fe45f2 active_list_add_depend: remove unused function
86b584d pkg_dependence_satisfied: remove unused function
816d330 Fix typo in pkg_hash_fetch_best_installation_candidate.
07f3b02 set_flags_from_control: remove function
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Support for the nct6775/6776 hwmon chips, and other compatibles
in the family as well as the Intel on-chip thermal sensors.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
update the qca988x firmware to firmware-5.bin_10.2.4-1.0-00029.
According to LEDE Forum, the new firmware supports mesh mode.
Also, it seems to have several improvements.
Signed-off-by: Changmin Jang <ckdalsdk12@gmail.com>
Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
If you're using Chrony or NTPD you don't want the busybox NTP server
as well. Make it's installation truly conditional.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [simplify]
Intel(R) 82576 is an adapter which supports SR-IOV. Thus the host can
assign Virtual Functions (VFs) to different VMs by the PCI-E Passthrough
(e.g. VFIO for KVM), to gain different advantages (performance, VF to VF
communications, host kernel offload, etc.).
The driver of the passthroughed VFs is the igbvf (igb is NOT
compatible).
This is essential for VM guests, to enable them to utilize this feature.
Signed-off-by: Ye Tao <tydus@hongo.wide.ad.jp>
Some of our local patches have been accepted upstream. And there are
some more relevant changes (mostly for rt2800usb). Import them and
rebase our remaining local patches on top.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The relay section should use the logical interface name and
not the linux network device name directly. This to be
consistent with other sections of the dnsmasq config where
'interface' means the logical interface.
Signed-off-by: Karl Vogel <karl.vogel@gmail.com>
20c16fc cmake: Make blockd link against libjson-c
92b4c2c libfstools: add basic documentation of mount functions
Signed-off-by: John Crispin <john@phrozen.org>
This is a 3rd party chipset which is not present on all Intel
reference designs, so make it a module rather than baked in (this
will also alleviate conflicts with drivers which also detect some
of the same chipsets).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
These are recommended practices by REC-22 and REC-24 of RFC6092:
"Recommended Simple Security Capabilities in Customer Premises Equipment
(CPE) for Providing Residential IPv6 Internet Service"
Fixes FS#640
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
ath10k tries to fetch board id via otp, but that fails for many chips
like QCA988x, QCA9984 etc. Recent commit cc189c0b7f removed the earlier
hack that had allowed QCA radios to work, as that hack was incompatible
with the new wifi chips being introduced to the source tree.
Restore functionality for the existing wifi chips by modifying the
return value of the 'board id via otp' function to a value that is recognised
as a harmless error, so that name evaluation continues by using the board file.
Patch originally suggested by Christian Lamparter in forum discussion.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
- remove unused code within 500-ar9_vr9.patch
- fixed return of IFX_ERROR (solves SIGSEGV in asterisk at failure)
- align it a bit with 400-falcon.patch
- remove 600-kernel-4.9.patch since changed parts
are removed during cleanup
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Make scan output useful for 802.11s meshes. The common print_ssid function
is used, so this doesn't add any additional code.
Based-on-patch-by: Jan-Tarek Butt <tarek@ring0.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Do not select the qca988x by default as soon as kmod-ath10k is
selected. We do support more ath10k chips than the qca988x in the
meantime, so this dependency doesn't make sense any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
0463b05 dhcpv6: rebind capability support in reconfigure message (rfc6644)
53767fc dhcpv6: respect renew end point when handling reconfigure message
dd892e2 dhcpv6: calculate T1, T2 and T3 in a more sane manner
8a6ca6e md5: use libubox md5 library as local implementation
89822de dhcpv6: don't return renew msg in case of invalid msg type in reconfigure msg
4160c0e treewide: align coding style
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The tx power applied by set_txpower is limited by the CTL (conformance
test limit) entries in the EEPROM. These can change based on the user
configured regulatory domain.
Depending on the EEPROM data this can cause the tx power to become too
limited, if the original regdomain CTLs impose lowr limits than the CTLs
of the user configured regdomain.
To fix this issue, set the initial channel limits without any CTL
restrictions and only apply the CTL at run time when setting the channel
and the real tx power.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If a device uses the default EEPROM code, typically only the main CTLs
are valid, and they do not apply properly when switching to a different
regulatory domain. If the regdomain deviates from the EEPROM one, force
the world roaming regdomain to ensure that power limits are sane
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update util-linux to 2.29.2
Remote 0001-fix-uClibc-ng-scanf-check.patch as it's been merged upstream.
Refresh patches
Change ncurses to ncursesw to fix compilation and avoid confusion
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove faulty dependency changes]
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
In the drv_mac80211_setup function, mac80211_interface_cleanup
is called to ask the kernel to delete all existing interfaces
for the phy that is being configured via netlink.
Later in the first function, mac80211_prepare_vif is called to
set up the new interfaces as required.
But sometimes, when mac80211_prepare_vif (and so the relevant
`iw phy x interface add y` command) runs, the kernel might still
be cleaning up the old interface with the same ifname. It usually
takes very few time to do that; possibly a few milliseconds of
sleep in the script after detecting this error condition could be
enough, but the busybox sh does not support sub-second sleep
intervals.
When this happens, iw obviously fails to create the new interface;
and the following message is printed in the system log, followed by
subsequent failure messages from hostapd in case this would have been
an AP interface.
Tue Mar 14 04:21:57 2017 daemon.notice netifd: radio1 (2767): command failed: Too many open files in system (-23)
This was a long-standing issue existing since at least OpenWrt Backfire,
and today I finally managed to debug and (hopefully) solve it.
It was happening very few times on most devices; but it was happening
a lot more frequently on fast platforms with multiple radios, such as
the powerpc-based dual-ath9k-radio tl-wdr4900-v1.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
On the ath10k-devel ML Michael Kazior stated:
"board-2 is a key-value store of actual board files.
Some devices, notably qca61x4 hw3+ and qca4019 need
distinct board files to be uploaded. Otherwise they
fail in various ways." [0].
Later on Rajkumar Manoharan explained:
"In QCA4019 platform, only radio specific calibration
(pre-cal-data) is stored in flash. Board specific contents
are read from board-2.bin. For each radio appropriate board
data should be loaded. To fetch correct board data from
board-2.bin bundle, pre-cal/radio specific caldata should
be loaded first to get proper board id.
|My understanding until now was that:
|
| * pre-cal data + board-2.bin info == actual calibration data
Correct." [1].
The standard board-2.bin from the ath10k-firmware-qca4019
barely works on the RT-AC58U. Especially 5GHz clients fail
to connect at all and if they do, they have very low
throughput even right next to the router.
Currently, the solution for this problem is to supply a
custom board-2.bin for every device.
To implement this feature, this method makes use of:
Rafał Miłecki's "base-files: add support for overlaying
rootfs content". This comes with a few limitations:
1. Since there can only be one board-2.bin at the right
location, there can only one board overwrite installed
at any time. (All packages CONFLICT with each other.
It's also not possible to "builtin" multiple package.)
2. updating ath10k-firmware-qca4019 will also replace
the board-2.bin. For this cases the user needs to
manually reinstall the wifi-board package once the
ath10k-firmware-qca4019 is updated.
To create the individual board-2.bin: Use the ath10k-bdencoder
utility from the qca-swiss-army-knife repository:
<https://github.com/qca/qca-swiss-army-knife>
The raw board.bin files have to be extracted from the
vendor's source GPL.tar archieves.
Signed-off-by: Alexis Green <agreen@cococorp.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
With this patch, the nand.sh script no longer overwrites
CI_KERNELPART and CI_UBIPART if they have been set before.
This allows platforms specify alternative values for these
variables.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch enables the ATH10K_AHB support for the QCA4019
devices on the AHB bus.
This patch also removes 936-ath10k_skip_otp_check.patch
because it breaks the AHB device identification.
"Patch is wrong. I find it frustrating OpenWRT/LEDE doesn't
try to work with upstream on ixing these things right."
[1] <https://www.mail-archive.com/ath10k@lists.infradead.org/msg05896.html>
It also limits ath10k memory hunger (This is a problem with 128MiB RAM)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This change protects the openvpn instances to be marked as "in a crash
loop" and thereby the connection retries will run infinitely.
When the remote site of an openvpn connection goes down for some time
(network failure etc.) the openvpn instance in an openwrt/lede device
should not stop retrying to establish the connection.
With the current limit of 5 retries, there is a user interaction
required, which isn't really what you want when the device should
simply do everything to keep the vpn connection up.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Add actual mirror and use main site as last resport
Source: http://www.tcpdump.org/mirrors.html
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Add mirror and use main site as last resort.
Source: http://www.tcpdump.org/mirrors.html
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update util-linux to 2.29.2
Remote 0001-fix-uClibc-ng-scanf-check.patch as it's been merged upstream.
Refresh patches
Change ncurses to ncursesw to fix compilation and avoid confusion
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Refresh mirror list, some doesn't offer OpenSSL and add main site as last resort.
Source: https://www.openssl.org/source/mirror.html
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
This includes following changes:
480d7bc Fix sending unicast questions on cache expire
a0403cd Keep source sockaddr for every cached DNS record
1478293 Fix code freeing cached non-A(AAA) records too early
9f1cc22 Fix replying to "QU" questions received on unicast interface
943bedb Fix reading port of incoming packets
c725494 Use MCAST_PORT define for port 5353
ce7e9e9 Use one define for DNS-Based Service Discovery service name
e1bacef Drop entries cached for interface we're going to delete
496aeba Fix comment typo in cache_gc_timer
f89986b Fix refreshing cached A(AAA) records that expire
Previous updates made umdns work as expected on startup but there were
still many bugs. They were mostly related to runtime - cache management
and requests + responses. E.g. umdns was never able to send question on
DNS record expire. It was also ignoring all incoming unicast questions.
Since these issues are quite serious it makes sense to backport this
update to the stable branch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
a032166 interface-ip: set prefix indicator flag when IPv6 prefix lifetime changes
b4f8984 system-linux: parse vti specific settings as nested json data object
7e3b89a system-linux: parse gre specific settings as nested json data object
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This is the standard way we handle this. Please note (it seems) I could
drop few symbols as they are hidden under (disabled) DRM_LEGACY now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
For targets with i2c not built-in this fixes following error:
Package kmod-drm is missing dependencies for the following libraries:
i2c-core.ko
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
If noresolv is set, we should not generate a --resolv-file parameter.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [minor cleanup]
9f02db7 mt76x2: fall back to software crypto for IBSS/Mesh per-sta GTK
4a54ab3 mt7603: fall back to software crypto for IBSS/Mesh per-sta GTK
712b8e8 mac80211: claim RSN IBSS support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The short log of changes since the 2016-06-10 release is below.
Jouni Malinen (1):
wireless-regdb: Remove DFS requirement for India (IN)
Ryan Mounce (1):
wireless-regdb: Update rules for Australia (AU) and add 60GHz rules
Seth Forshee (2):
wireless-regdb: Update 5 GHz rules for Canada
wireless-regdb: update regulatory.bin based on preceding changes
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
uClibc doesn't implement strerror_l() and thus libnl starting from
3.2.29 couldn't be compiled with it any longer, see
6c2d111177
To work-around that problem we'll just do a check on strerror_l()
availability during configuration and if it's not there just fall back
to locale-less strerror().
Patch for libnl is alreadfy merged upstream, see
e15966ac7f
and once the next libnl release happens this one must be removed from
Lede/OpenWrt.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Daniel Engberg <daniel.engberg.lists@pyret.net>
ntpd from Busybox supports peer-less (standalone) mode when it's started
with option -l and without any peer provided with option -p. In this
mode ntpd uses local time as reference and acts as stratum 1 server.
This mode can be used in isolated networks, where Internet access and/or
other NTP server/s are not available, but the device has some other way
of getting correct time, like e.g. GPS (ugps supports setting local time
by default).
Support for this mode was incorrectly disabled/removed in:
1527f96ca6
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
musl provides a /lib/libc.so file which should be integrated into the libc
package when the external toolchain with musl is used.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
03e44dc mt76x2: remove unnecessary headroom check
cc70498 mt76x2: clarify queue selection field
b056a78 dma: fix endian issue in mt76_dma_get_buf
f020a60 mt7603: support loading the entire EEPROM from OTP
29b08d3 mt7603: fix endian issue in mt7603_mcu_set_timing
dce8aac mt7603: fix endian issue in mt7603_mac_fill_rx
f22273b mt7603: init WTBL entry before setting capabilities
da8e796 mt7603: check wtbl busy status and stop/start tx queues when clearing sta entry
e54add5 mt7603: move napi/tasklet enable/disable outside of the locked section
59ce2b4 mt7603: set tx vif own MAC index (needed for beacons)
93ce124 mt7603: enable beacons for other virtual interfaces
c91e660 mt7603: set secondary beacon time offsets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This includes 3 cleanups:
fd5a160 Don't cache hosts as services
80dd246 Refresh DNS records A and AAAA directly
6515101 Access cached records (instead of services) to read list of hosts
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes the following security problems:
* CVE-2017-2784: Freeing of memory allocated on stack when validating a public key with a secp224k1 curve
* SLOTH vulnerability
* Denial of Service through Certificate Revocation List
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel unconditionally pulls in a header file that defines
'current', which conflicts with the lua extension code.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce RT6352 instead of matching against RF7620.
Clean up channel setting rfvals.
Port bandwidth filter calibration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Overwrite an already set proto if a new one is passed to
_ucidef_set_interface() similar to what is done for the interface.
It is required when using ""ucidef_set_interface_wan 'ptm0' 'pppoe'"
after some initial wan interface configuration is already done by
ucidef_add_switch.
The "json_is_a protocol string" guard is meant to not reset an earlier
set interface proto in case something like
"ucidef_set_interface_lan 'eth0'" is used afterwards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes crash in interface_start caused by freeing interface in
interface_free without stopping a timeout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So here is another round of improvements for MT7620 WiFi.
This commit fixes a few significant issues related to TX_PWR_CFG_x and
TX_ALC and also makes the code more readable by adding register
descriptions for things added for MT7620 and use the usual bit-field
access macros and the now defined macros instead of plain bit-ops and
magic numbers.
Properly describe EEPROM_TARGET_POWER at word 0x68 (== byte 0xD0) and
thereby fix internal TXALC which would otherwise just read
out-of-bounds of the EEPROM map.
Split-out tx-power/ALC related stuff into an additional function.
Fix VCO calibration, it was carried out properly in the channel
switching but incomplete in the actual VCO calibration function.
Also there is no need to trigger VCO calibration in channel switching,
the VCO calibration function is already being called at this point.
Remove it from channel switching function to avoid redundant code.
The TX power calibration differs significantly from all other
Mediatek/Ralink chips: They finally allow 0.5dB steps stored as 8-bit
values for (almost) each bitrate -- and promptly ran out of space and
for some reason didn't want to change the EEPROM layout. The hence
opted for a scheme of sharing values for some adjecent bitrates and
a highly over-complicated (or obfuscated?) way to populate the
TX_PWR_CFG_x registers with the values stored in the EEPROM.
The code here now looks much less complicated than what you see in the
vendor's driver, however, it does the exact same thing:
bGpwrdeltaMinus is a constant and always TRUE, hence half of the
code was dead. Gpwrdelta is always 0 (rather than using the value read
from the EEPROM). What remains is some very grotesque effort to avoid
0x20, probably some hardware bug related to some misunderstanding of
what a singed 8-bit value is (imagine: if it was a signed 6-bit value
then someone could believe that 0x20 == 0x0). And then they didn't
clean it up once they later on anandonned that whole story of having a
constant offset for 40 MHz channels and just set the offset to be
constant 0 -- there is no effort for avoiding 0x20 for the 20 MHz
values stored in the EEPROM, hence that's probably just a forbidden
value in the EEPROM specs and won't appear anyway...
Anyway, the whole thing felt like solving some college math test
where in the end everything cancels out and the result equals 0 ;)
To make sure that channel bandwidth power compensation really doesn't
need to be taken care of, output a warning when the corresponding
value stored in the EEPROM is non-zero.
Also there is no apparent reason to refrain from initializing RFCSR
register 13, it doesn't fail what-so-ever.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
RFC 6761 defines a number of top level domains should not be forwarded
to the Internet's domain servers since they are not responsible for
those domains.
This change adds a list of domains that will be blocked when 'boguspriv'
is used and augments that which is already blocked by dnsmasq's notion
of 'local service' using '--bogus-priv' i.e. RFC 1918 private addresses
and IPv6 prefixes as defined in RFC 6303.
To make this configurable rather than hard coded in dnsmasq's init
script, a new file /usr/share/dnsmasq/rfc6761.conf is conditionally
included.
The default file matches the RFC 6761 recommendation along with a few
other top level domains that should not be forwarded to the Internet.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The ugps tool expects device path in last argument. If it's provided
before other options, they won't be processed at all.
Additionally, make it possible to use absolute path for gps character
device in related uci configuration.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
continue work started here: http://patchwork.ozlabs.org/patch/520859
Extend /etc/config/system with parameters to set the default respawn treshold and respawn timeout
for procd launched services that have respawn enabled.
This results in cleaner init scripts, while making sure services have respawn parameters set.
Signed-off-by: Claudiu Brasovean <cbrasho@gmail.com>
Open-code usb_phy_generic_register instead of calling it, since it is
really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel
config and add a proper dependency instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If ehci platform driver is loaded before the chipidea controller driver,
both are competing for the same IO resources and the generic driver gets
used for the hardware. This results in USB device mode being
unavailable.
Split generic EHCI support code out of kmod-usb2, so that the chipidea
driver can be included without also pulling in the generic one. Also
rework the load order, so that the chipidea driver gets loaded first, in
case both are installed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Honour the parent interfaces peerdns option when spawning a virtual DHCPv6
interface in order to avoid pulling in IPv6 DNS servers when the user opted
to inhibit peer DNS servers in the configuration.
Fixes#597.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
8f218f5 procd: service gets deleted when its last instance is freed
35209a0 procd: update modprobe path
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Update to latest Git in order to import the following fixes:
19070b6 unarchive: fix possible segmentation fault in deb_extract()
758527e pkg: forward "provided_by_hand" flag in pkg_merge()
1fdc2ca pkg: mark bit fields in pkg_t unsigned
15fc1ee opkg_cmd: avoid null pointer dereference in opkg_what_depends_conflicts_cmd()
439c89e opkg_cmd: fix endless loop in whatprovides/whatreplaces
0fb3e9f pkg_depends: propagate virtual provided detail flag to providers
793155f pkg_depends: fix unsatisfied dependency installation order
b1dc770 libopkg: fix some overly aggressive line wrapping in pkg_depends.c
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We need to let external toolchains be able to specify the path and
specification file to the libthread-db POSIX thread debugging shared
libraries.
This fixes GDB not being able to be installed because it is depending on
libthread-db:
Collected errors:
* satisfy_dependencies_for: Cannot satisfy the following dependencies
* for gdb:
* libthread-db *
* opkg_install_cmd: Cannot install package gdb.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The current way of creating a STAMP_CONFIGURED filename for OpenSSL can
lead to an extremely long filename that makes touch unable to create it,
and fail the build.
Use mkhash to produce a hash against OPENSSL_OPTIONS which creates a
shortert stamp file,
Fixes#572
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pass down TARGET_CPPFLAGS for path to header files, and append the
libraries we depend on in TARGET_LDFLAGS. Put TARGET_LDFLAGS at the end
of the command line as is required by modern GCC/binutils.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes build issues with external toolchains that do not have STAGING_DIR
in their default search path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes linking failures observed with external toolchains:
/home/florian/dev/toolchains/stbgcc-4.8-1.5/bin/../lib/gcc/mipsel-linux-gnu/4.8.5/../../../../mipsel-linux-gnu/bin/ld:
warning: libubox.so, needed by
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so,
not found (try using -rpath or -rpath-link)
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_open_nested'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_parse'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blob_nest_end'
/home/florian/dev/openwrt/trunk/staging_dir/target-mipsel-unknown-linux-gnu_glibc/usr/lib/libuci.so:
undefined reference to `blobmsg_add_field'
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make sure we pass down TARGET_CPPFLAGS to let toolchains with no default
search paths to find the mbdetls headers, and override TARGET_LDFLAGS to
include libraries we are linking against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Brings the following changes:
22f041e18df0 Extend StandardEject sequence to include LUN 1
61fdf7e9b1cc cmake: Search for libjson-c
2769852e76b5 cmake: Find libubox/blobmsg_json.h
8a47c4b6649f add TargetClass support
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
thc-ipv6 did not allow an external environment to override CFLAGS, which
would lead to our CFLAGS not being passed properly (relro,
optimizations, etc...)
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The following will enable the TPM kernel module, as well as support for
the atmel i2c TPM driver. Tested and confirmed working on an Aerohive
AP-121
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Drops a LEDE carried patch now upstream.
Convert to autotools.
A number of nits fixed upstream (dns & short packet handling most
notable)
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
c09e4f0 ubusd: fix incomplete copy of shared buf during queue-ing
453b87f cli: add support for subscribing to objects
6eb3c96 cli: do not use default timeout for listen
dfe3383 libubus: reset ctx->sock.error when doing ubus reconnect
34c6e81 cli: fix listen_timeout compile issue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is required for default wireless configuration of malta target to
work out of the box again. Fixes "77ece30e: hostapd: Add ability to
specify that that wireless driver supports 802.11ac"
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
When not defining 'device' or 'vlan' in relevant switch_port uci
sections, behaviour is inconsistent due to *devn, *port and *vlan
pointers not being zero initialized.
Signed-off-by: Ben Kelly <ben@benjii.net>
This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
stop() is overwritten by rc.common, so implement stop_service instead.
While at it, remove the now unnecessary restart() override
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch splits `kmod-mt76` into three separate packages:
`kmod-mt76-core`, `kmod-mt76x2` and `kmod-mt7603`. By making
`kmod-mt76` a metapackage containing these new packages,
the previous behaviour of including all drivers and firmware
is left unchanged, unless explicitly unselected in
`DEVICE_PACKAGES`.
This splitting is especially beneficial for devices with
small flash chips, since the `kmod-mt76` package currently
requires ~160K on squashfs (after compression).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
Update to latest Git head to get rid of a stray printf() causing unwanted
output in the "opkg list-upgradable" command.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
--bogus-priv now applies to IPv6 prefixes as specified in RFC6303 - this
is significantly friendlier to upstream servers.
CNAME fix in auth mode - A domain can only have a CNAME if it has no
other records
Drop 2 patches now included upstream.
Compile & run tested Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
A missing list pointer initialization caused opkg to ignore conffile entries
from status files, breaking the conffile tracking on the target.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
c553354 cmake: fix typo
8973576 kmodloader: fix not being able to find some modules
fce9382 cmake: Check for getrandom system call
Signed-off-by: Felix Fietkau <nbd@nbd.name>
px5g-standalone only supports SHA1 for certificates, which is strongly
deprecated. The new px5g-standalone is about 27k bigger (compressed),
and has identical behavior to px5g-mbedtls (it uses SHA256).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
