Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Eth0 is attached to mac0 of the switch with a fixed link and and not to
phy4 in single phy mode, so configuring it to anything but 1000FD will
break the connection, which will happen if a only 100 Mbit capapble device
is plugged into the wan port.
Fix this by not taking the state from phy4 and just configuring a fixed link
for eth0.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47695
the board names used by the upgrade check differ from the device names
in case, so always set them. We can't rely on tolower or similar since
different locales might have different rules for lower case letters, so
set them explicitily.
Fixes sysupgrade rejecting *-sysupgrade.tar because of the difference.
Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47381
We're in process of cleaning nand_do_platform_check. Currently is leaves
a special mark in /tmp/sysupgrade-nand-path triggering some diffent code
path in nand_upgrade_stage1. This can be a bit confusing.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
This follows ar71xx, lantiq and partially bcm53xx.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46945
In krait_cpufreq_probe, both freq and max_cpu_freq are never
initialized, so the max_cpu_freq will have a random value at the end.
Fix this by properly initializing max_cpu_freq to 0 and storing the clk
frequency in freq as well, to make it similar to how it's calculated in
krait_set_target.
Fixes the following warnings:
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
drivers/cpufreq/cpufreq-krait.c: In function 'krait_cpufreq_probe':
include/linux/kernel.h:714:24: warning: 'freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:25: note: 'freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
^
In file included from include/linux/clk.h:16:0,
from drivers/cpufreq/cpufreq-krait.c:13:
include/linux/kernel.h:714:24: warning: 'max_cpu_freq' may be used uninitialized in this function [-Wmaybe-uninitialized]
_max1 > _max2 ? _max1 : _max2; })
^
drivers/cpufreq/cpufreq-krait.c:217:31: note: 'max_cpu_freq' was declared here
unsigned long freq_Hz, freq, max_cpu_freq;
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46839
The phy driver has its qcom-dwc3 order switched in contrast to the usb
controller driver.
Signed-off-by: Kaspar Schleiser <kaspar@schleiser.de>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46838
Add support for the Netgear Nighthawk X4 R7500 and build
appropariate sysupgrade and factory images.
Known issues:
* 5 GHz wifi not working - there is no quantenna driver
* One of the USB ports is not working
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46796
To use gpio leds as ide leds, we need to enable the trigger to be
included in the kernel.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46795
Add full ubi and sysupgrade images for AP148 and add sysupgrade support
for ipq806x to allow updating the current installation.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46789
*Enable SMEM MTD parser and its dependencies (SMEM & HW spinlocks) in
the kernel config
*Replaces the MTD layout in DT by the dynamic layout provided by the
SMEM parser for AP148
Using the OF based parser is still possible on platforms which have a
fixed MTD partition layout.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46658
This patch adds a new parser which uses the SMEM available on IPQ and
some other QCOM platforms to map the MTD partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46657
2 patches are cherry-picked from the following LKML thread:
*https://lkml.org/lkml/2015/4/11/208
The last patch (036-soc-qcom-add-smem-to-IPQ806x-platforms.patch) is
adding the corresponding DT nodes required for IPQ806x.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46656
This change cherry-picks the following 3 changes from linux-next:
*fb7737 hwspinlock/core: add device tree support
*19a0f6 hwspinlock: qcom: Add support for Qualcomm HW Mutex block
*bd5717 hwspinlock: qcom: Correct msb in regmap_field
We're also adding a patch to add the hardware spinlock device nodes on
IPQ806x platforms (033-soc-qcom-Add-sfbp-device-to-IPQ806x-dts.patch).
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46655
Switch ipq806x to the new image build system. Image files might change
slightly their names, but the generated files should not change.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46602
Linux 4.1 is also affected from the dma issue, so remove the dma
proprties there as well.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46599
Previous patch 6f2905eeb6ce5ddec8d12d677e1f377a940b537b enabled ADM in
the kernel, which causes a kernel panic when accessing the SPI flash.
As a workaround, We'll disable DMA for the flash for now. It was not
enabled previously anyway so we'll just leave it as is.
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46587
Previous patch set backported the recently posted NAND flash driver to
3.18 and 4.1 kernel. This patch now enables it in the kernel config.
There is no change to the partition layout and init yet. But the NAND
flash can be seen in the mtd list on an AP148:
root@OpenWrt:/# cat /proc/mtd
dev: size erasesize name
mtd0: 10000000 00020000 "qcom-nandc"
...
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46569
These patches add support for ipq806x NAND flash controller. Most of
these are cherry-picked & backported from LKML:
*https://lkml.org/lkml/2015/8/3/16
This patch just modifies the kernel code, but doesn't change the config.
It should be harmless.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46568
These are cherry-picked & backported from LKML:
*https://lkml.org/lkml/2015/3/17/19
They are enabled on both 3.18 and 4.1 kernel. Patches 150 to 154 are
applying changes merged since 3.18; they enable mechanisms used by the
ADM driver.
ADM engine is used by the NAND controller, so it is necessary to
bring-up NAND flash support.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46567
We forgot to enable the stmmac driver for 4.1 kernel, so ethernet
interfaces don't show-up on this kernel.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46559
Old bootloader (same ones which have DT disabled) don't perform any PCIe
initialization. The consequence is a freeze during PCIe bring-up on
these old u-boot. Same kernel with a newer bootloaders works fine as
they contain the corresponding PCIe init code.
In this change, we'll add the missing init and make sure the kernel
doesn't rely on some preexisting init to get PCIe to work. That includes
the following changes:
*GPIOs: set function & drive strength
*Clocks: add init code for aux & ref clocks
*PCIe driver: additional init of the hardware controller
Tested 3.18 and 4.1 on an AP148 with bootloader branch 0.0.1
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46557
PCIe controller nodes are numbers 0/1/2 in the chipset dtsi file, but
the pinmux nodes are numbers 1/2/3. We'll make it consistent by changing
the pinmux numbering to match the controller's one.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46556
Certain AP148 platforms (and derivative) use bootloaders which did not
have DT enabled.
In order to support these old platforms, we'll now make the following
modifications:
*explicitely add the memory node in the AP148 DT: this used to be added
by new u-boot through a run-time patch mechanism. We'll now add it
explicitely so it works on boots which don't support that feature. New
boots will have the node twice, the second one will be ignored.
*add the zImage generation next to the FIT image for AP148.
Other platforms using non-DT enabled bootloaders may want to leverage
this zImage code to generate their own firmare as well.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 46555
