It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
FS#256
Fix audio not working due to unset SND_PCM_TIMER. CONFIG_SND_PCM_TIMER
is required for ALSA to work (at least for some audio devices),
otherwise applications using sound may fail. Can be reproduced by
installing "alsa-utils-tests" and running "speaker-test":
...
ALSA lib pcm_direct.c:1159:(snd1_pcm_direct_initialize_poll_fd) unable to open timer 'hw:CLASS=3,SCLASS=0,CARD=0,DEV=0,SUBDEV=0'
ALSA lib pcm_dmix.c:1106:(snd_pcm_dmix_open) unable to initialize poll_fd
Playback open error: -19,No such device
The kernel size does not increase, only the size of the kernel module
increases.
Signed-off-by: Dmitry Sutyagin <f3flight@gmail.com>
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).
Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Since commit 484cb91 "sdk: bundle required firmware files" there is an
implicit dependency of the SDK on a prior Kernel compilation.
Change target/Makefile to make this dependency explicit to avoid race
conditions with parallel builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Specifying a mtune option with cortex-a53 is also valid for an aarch64
toolchain
Fixes: SVN 48964
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This reverts commit efd9dec319.
ath10k can take a long time to probe, long enough for netifd to fail to
initialize already configured wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Switch to xz compression instead of using bz2.
This makes a considerable difference in size, ar71xx SDK from 60M to 35M.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks
Signed-off-by: Mathias Kresin <dev@kresin.me>
LEDE no longer requires all PHYs to be initialized to
create the configuration files during bootup. This patch
removes the now obsolete ath10k patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the wifi detection script is executed as part of
the (early) boot process. Pluggable wifi USB devices, which
are inserted at a later time are not automatically
detected and therefore they don't show up in LuCI.
A user has to deal with wifi detection manually, or restart
the router.
However, the current "sleep 1" window - which the boot
process waits for wifi devices to "settle down" - is too
short to detect wifi devices for some routers anyway.
For example, this can happen with USB WLAN devices on the
WNDR4700. This is because the usb controller needs to load
its firmware from UBI and initialize, before it can operate.
The issue can be seen on a BT HomeHub 5A as well as soon as
the caldata are on an ubi volume. This is because the ath9k
card has to be initialized by owl-loader first. Which has to
wait for the firmware extraction script to retrieve the pci
initialization values inside the caldata.
This patch moves the wifi configuration to hotplug scripts.
For mac80211, the wifi configuration will now automatically
run any time a "ieee80211" device is added. Likewise
broadcom-wl's script checks for new "net" devices which
have the "wl$NUMBER" moniker.
Issues with spawning multiple interface configuration - in
case the detection script is run concurrently - have been
resolved by using a named section for the initial
configuration. Concurrent configuration scripts will now
simply overwrite the same existing configuration.
A workaround which preserves the "sleep 1" window for just
the first boot has been added. This allows the existing
brcm47xx boot and mvebu uci-default scripts to correctly
setup the initial mac addresses and regulatory domain.
And finally, the patch renames the "wifi detect" into
"wifi config". As the script no longer produces any output
that has to be redirected or appended to the configuration
file.
Thanks to Martin Blumenstingl for helping with the implementation
and testing of the patch.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Previously, wifi detect simply dumped its generated wireless
configuration to STDOUT. A second step was needed to append
the configuration to /etc/config/wireless (or create it, if
it didn't exist).
With this patch, The wifi detection script will now use uci
to update the wireless configuration directly.
This patch also makes the initially created wifi-iface a
named section ('default_radio$X' for mac80211 and
'default_wl$X' for broadcom). With this change, uci will
not print the cfgHASH to STDOUT (which would now corrupt
the wireless configuration). It will also prevent adding
duplicated wifi interface configurations, if the wifi
configuration is run concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds a check in "wifi detect" to test if the wireless
configuration file does exist. If it doesn't exist, an empty
/etc/config/wireless file will be created.
This is necessary because uci doesn't create new files,
instead the tool just exits with "uci: Entry not found".
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It's always hard to find a reasonable width that will make everyone
happy. This one at least makes "telephony" (one of default feeds) name
fit the column and hopefully isn't too big.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver
Also switching to ondemand frequency scaling as it is fixed now
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.
Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
Rename the "ip" package declaration to "ip-tiny" and let both "ip-tiny" and
"ip-full" provide the virtual "ip" package. This allows users to freely choose
the "ip" command variant while other packages can continue to depend on "ip"
without needing to enforce a specific variant.
Note that this commit does not add busybox as "ip" provider due to
the following reasons:
- The builtin Busybox ip applet cannot be added or removed at runtime
- Both "ip-tiny" and "ip-full" are able to install without file clashes even
if the busybox applet is enabled
- The system is preferring full "ip-tiny" and "ip-full" at runtime, even
if Busybox ip is still present.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The current uboot default config for the A13 SOM erroneously enables support
for the AXP209 power regulator IC which is not present on the board.
This superfluous support module sets an incorrect initial clock frequency and
confuses the kernel, ultimately leading to a boot failure later on.
Properly disable the PMIC support and enable the EHCI support by translating
the deprecated SYS_EXTRA_OPTIONS values into proper SUNXI_NO_PMIC and
USB_EHCI_HCD symbols respectively.
Also rename 002-add-olimex-a13-som.diff to 002-add-olimex-a13-som.patch and
refresh the remaining patches of the series while we're at it.
Reported-by: Mario Fischer <mario-fischer@web.de>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
So far, package-metadata.pl always considered the first provider of a virtual
package to be the default variant which might deviate from what buildroot
considers to be the default.
Change the Kconfig dependency / select code generation for virtual package
providers to consider the DEFAULT_VARIANT to be the primary provider and only
fall back to the first provider if no default variant was explicitely tagged.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce support for a new [0-9]u@netdev syntax to ucidev_add_switch() to let
board.d network files request default network switch configurations which do
not use tagged CPU ports.
This commit itself has no effect on generated configurations at the moment
since we still emit untagged configurations by default but it allows boards to
opt-out from default tagged configs in case we start emitting tagged settings
by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Right now the $(PKG_INSTALL_STAMP) files are only written if a package is
selected as <*> but never deleted or emptied if the corresponding package
is getting deselected.
For ordinary packages this usually is no problem as the package/install
recipe performs its own check for enabled packages when assembling the
list of install stamp files to consider, but this logic might fail under
certain circumstances for packages providing multiple build variants.
In case of a multi-variant package, the buildroot first checks if any
of the variants is enabled, then resolves all variants of the common
source package and finally processes the corresponding .install stamp
files of all variants, relying on the assumption that only the selected
.install stamp file exists.
When an initially selected variant is getting deselected or changed from
<*> to <m> and another variant is marked as <*> instead, the .install
stamp file of the deselected variant remains unchanged and a second
.install stamp file for the newly selected variant is getting created,
causing the package/install recipe to pick up two .install stamps with
conflicting variants, leading to opkg file clashes.
This issue happens for example if package "ip" is set to <m> and package
"ip-full" to <*> - the install command will eventually fail with:
* check_conflicts_for: The following packages conflict with ip:
* check_conflicts_for: ip-full *
* opkg_install_cmd: Cannot install package ip.
In order to fix the problem, always process the removal requests or the
.install stamp files, even for deselected packages but only write the
package base name into the stamp file if the corresponding package is
marked as builtin.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
