Keep Archer C20 Power LED in the same state as it was configured by
bootloader (keep it hightlighed) to avoid unexpectable LED turning off
during kernel boot.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Add the missing USB related kernel config options to target config.
Enable wireless as well, wireless is supported via USB.
Fixes compile/packaging errors with the libertas wireless kernel
module.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Do not disable SPI in the subtarget, otherwise the SPI driver can not
be used.
Disable SPI by default and enable it in the board specific device tree
source file.
Signed-off-by: Mathias Kresin <dev@kresin.me>
AmazonSE and Falcon do not have support for PCI and it can't be
unselected in the subtarget kernel config. This way the enabled PCI
support is inherit from the higher level config to the subtarget.
If CONFIG_PCI is selected, PCI_SUPPORT will be autoselected as well and
all packages depending on this config symbol will be build and at least
some of them fail due to missing pci functions.
The issue can be observed if all kmods and all non-shared packages are
build. Fix the issue by enabling PCI support only in subtargets with
PCI support.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The subtarget kernel config options CONFIG_CC_OPTIMIZE_FOR_SIZE and
CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK are already set by the target or
global kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_SPI_LANTIQ was replaced by CONFIG_SPI_LANTIQ_SSC with the switch
to the upstreamed driver.
All other removed subtarget kernel config options are already set by
the target specific or global kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_MTSCHED & CONFIG_PERFCTRS were never defined in the kernel.
CONFIG_LANTIQ_PHY was replaced by CONFIG_INTEL_XWAY_PHY with the switch
to the upstreamed driver.
Add autoselected dependecies to the kernel config.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_GPIO_DEVRES was removed with kernel commit f9c22ec6c1c5 ("gpio:
Remove GPIO_DEVRES option") during kernel 4.9 development.
CONFIG_HAVE_BPF_JIT was removed with kernel commit 6077776b5908 ("bpf:
split HAVE_BPF_JIT into cBPF and eBPF variant") during kernel 4.7
development.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following features are working and tested:
* both Ethernet ports
* MMC
* LED
The following features are not working:
* Wifi (There is a crappy driver we could port)
* SPI flash (I haven't looked into this)
I haven't tried out the rest.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
check if the config option CONFIG_LANTIQ is defined.
This fixes the following warning:
CC [M] drivers/misc/owl-loader.o
drivers/misc/owl-loader.c: In function 'ath9k_pci_fixup':
drivers/misc/owl-loader.c:92:5: warning: "CONFIG_LANTIQ" is not defined [-Wundef]
#if CONFIG_LANTIQ
^
Fixes: e9401a2335 ("kernel: owl-loader for delayed Atheros ath9k fixup")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner H3 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds the device tree changes needed to make the GMAC stmmac driver
working for the Allwinner A64 SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for the GMAC which is use in the A64 and other
Allwinner chips by backporting the changes from the kernel versions
4.13.
Some commits are not backported which are adding support for newly
introduced APIs which are not available in kernel 4.9.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Booting from jffs2 directly is no longer supported, use
rootfstype=squashfs consistently for all subtargets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The RT5350F's second UART pins are available on the base module and on
the EVB as well, so enable it in the device tree.
In order to keep the origian serial port numbering (ttyS0 is the serial
console), aliases added for the UART devices.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The RT5350F i2c pins is available on the base module and on
the EVB as well, so enable it in the dts.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The polarity of WLAN_ACT LED on the base module needs to inverted
in order to be 'on' when the WiFi interface is active
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The RT5350F-OLINUXINO(-EVB).dts files' content are nearly the same, so to avoid
code duplication this patch creates RT5350F-OLINUXINO.dtsi file which
covers the base board's features. The corresponding RT5350F-OLINUXINO.dts
just includes the new .dtsi and the RT5350F-OLINUXINO-EVB.dts adds the EVB
specific GPIO config.
Signed-off-by: Zoltan Gyarmati <mr.zoltan.gyarmati@gmail.com>
The Xiaomi Mi Router 3G uses this deranged vlan portmap. Add support so
that packets are not leaked across all switch ports when reset.
Fix a whitespace nit while we're here.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fix wrong pvids order]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Disable VLANs on mt7621 boards with mt7530 switches on failsafe entry.
Allows failsafe networking to work correctly.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
[fixed default case syntax error]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 31e9445b7e.
"Linksys E1200 V1" is not a valid board name, as the brcm47xx arch code
can not detect this device. Stefan Lippers-Hollmann also found a typo in
this patch "cybetran" instead of "cybertan".
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[replaced u-boot patch with original version from u-boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
x86_64 platforms typically don't lack memory, so don't needlessly
economize memory if fq_codel on capable platforms.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
[Add a comment to the patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mediatek MT7621 soc watchdog DTS id was renamed from "mtk,mt7621-wdt" to
"mediatek,mt7621-wdt" when driver upstreamed to kernel 4.5
Update mt7621.dtsi & mt7628an.dtsi definitions to match upstreamed
kernel.
Restores hardward watchdog functionality on mt7621 devices under linux
4.9
Tested on: MIR3G
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.
Fixes the following CVEs:
- CVE-2017-14106
- CVE-2017-14497
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for SAMA5D4 with target device as at91-sama5d4_xplained
in SAMA5 subtarget and build images for SAMA5D4 Xplained board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D2 with target device as at91-sama5d2_xplained
in SAMA5 subtarget and build images for SAMA5D2 Xplained board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Renaming at91 subtarget sama5d3 to sama5 and using at91-sama5d3_xplained
as a target device in sama5 subtarget.This will enable to add other
sama5d2 & sama5d4 target devices in sama5 subtraget.This will avoid
code duplication when sama5d2 & sama5d4 added as different subtarget.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This adds initial support for the A64 Allwinner SoC to LEDE.
It will be build in the new cortexa53 subtarget.
Currently it only supports the pine64 and the image is able to boot on
this SoC.
Camera, Ethernet, HDMI and other parts are currently not working.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports some more patches from kernel 4.11 adding more devices
to the device tree of the A64 SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports multiple patches from kernel 4.10 which are adding
missing support for the A64 and the pine64 board. These are the device
tree files, the pinctlk and the clock driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required to support kernel 4.9.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
[rewrite commit message (subject <= 50 characters)]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refresh patches.
Compile-tested on ipq8065/nbg6817 and x86/64.
Runtime-tested on ipq8065/nbg6817 and x86/64.
Fixes CVE-2017-1000251.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[adapt qcom_nandc.c patches to match upstream changes, test ipq8065/nbg6817]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Delete a bunch of fixes that are already included.
Refresh patches.
Compile-tested on malta/mipsel
Runtime-tested on malta/mipsel
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
4.4.80+ contains 71a165f6397df07a06ce643de5c2dbae29bd3cfb, 4.9.41+ contains
6c78197e4a69c19e61dfe904fdc661b2aee8ec20 which are all backports of upstream
commit 0878fff1f42c18e448ab5b8b4f6a3eb32365b5b6 ("net: phy: Do not perform
software reset for Generic PHY").
Our local patch is no longer needed, all this patch was doing was utilizing
gen10g_soft_reset which does nothing either, so just keep the code unchanged.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We will be prompted with this config symbol when performance monitoring is
enabled in the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The factory partition of the Phicomm K2P contains two MAC addresses.
The lower MAC address is at offset 0xe006 and the higher one is at
offset 0xe000.
Use the lower MAC address as base mac-address which the switch driver
increments by one for the second (wan) vlan.
The MAC addresses are still inverted in contrast to the stock firmware
where the lower MAC address is used for wan. But at least the use of a
MAC address not intended/reserved for this particular board is fixed.
Signed-off-by: Jiawei Wang <me@jwang.link>
In commit b11c51916c ("ramips: Improve Sanlinking D240 config") I made
a mistake with regards GPIO numbering. And in addition to specifying the
wrong GPIO for controling the power of one of the mini-PCIe, I recently
discovered that the power of both slots can be controlled.
This patch specifies the correct GPIO for the left-most mini-PCIe slot
of the D240 (labeled power_mpcie2 since the slot is attached to SIM2),
and adds a GPIO that can be used to control the power of the other
mini-PCIe slot (labeled power_mpcie1).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[do not use the gpio active macros for the gpio-export value]
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link Archer C20 v1 is a router with 5-port FE switch and
non-detachable antennas. It's very similiar to TP-Link Archer C50.
Also it's based on MediaTek MT7620A+MT7610EN.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 8x LED (GPIO-controlled*), 2x button, power input switch
- 1 x USB 2.0 port
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the blue part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash. So, to flash this device we must
to prepare image using original firmware from tp-link site with uboot.
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot.
There are two ways to flash the device to LEDE:
1) Using tftp mode with UART connection and original LEDE image
- Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp
server directory
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, power up the router and press
key "4" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
setenv serverip 192.168.0.66
tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
- After that the device will reboot and boot to LEDE
2) Using tftp mode without UART connection but require some
manipulations with target image
- Download and unpack TP-Link Archer C20 v1 firmware from original web
site
- Split uboot.bin from original firmware by this command (example):
dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1
- Create ArcherC20V1_tp_recovery.bin using this command:
cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin
- Place ArcherC20V1_tp_recovery.bin in tftp server directory.
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
- Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
The implementation is not efficient on ar8xxx switches. It triggers high
CPU load and degrades device performance.
The high CPU load has been traced down to the ar8xxx_reg_wait() call in
ar8xxx_mib_op(), which has to usleep_range() till the MIB busy flag set
by the request to update the MIB counter is cleared.
This commit removes the get_port_stats() code introduced in 4d8a66d and
leaves a note for future hacker's beware.
Fixes: FS#1004
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.
Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The ZBT WE1026-5G
(http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up
to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the
ZBT WE826 image could be used. However, as the name implies, the -5G
comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz
radio, the addition of 5GHz means that a separate image is needed for
the WE1026-5G. I suspect that this image will also work on the previous
WE1026, but I don't have a device to test with.
The WE1026-5G has following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x 5GHz wifi (MT7612)
* 1x button.
* 3x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working:
* The 5GHz WIFI LED is completely dead. I suspect the issue is the same
as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is
controlled by the driver, and mt76 (currently) does not support this.
Not tested:
* SD card reader.
Notes:
* The modem (labeled 3G/4G) and power LEDs are controlled by the
hardware.
* There is a 32MB version of this device available, but I do not have
access to it. I have therefor only added support for the 16MB version,
but added all the required infrastructure to make adding support for the
32MB version easy.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the
reset button pressed for ~5sec when booting to start the web server. Set the
address of the network interface on your machine to 192.168.1.2/24, and
point your browser to 192.168.1.1 to access the recovery UI. From the
recovery UI you can upload a firmware image.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
On a TL-WN710N, this patch increases iperf performance from ~92.5 to ~93.5 mbps. Keep in mind the WN710N is a 100mbps device. I expect greater numbers from gigabit devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The cns3xxx interrupt controller uses a single register and as such
the 'mask' reg/functions must be used as opposed to the 'enable'/'disable'
reg/functions.
This fixes an issue that occurs if more than one GPIO on a specific controller
(there is GPIOA and GPIOB each having 32 GPIO's) uses interrupts. When one
would get enabled all others would be disabled prior to this patch.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.
Fixes CVE-2017-11600.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This adds metadata to wpj344 and wpj558 images to prevent loading
firmware of wpj344 into wpj558 and vice versa. This until now was
possible and break the units and had to be recovered from the uboot.
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.
Short specification:
- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
For the Archer C50v1, the EU and US versions are differentiated by their
respective HW additional version (0x0 for US, 0x2 for EU).
The stock web interface checks this field before flashing, making it
impossible to flash the current (US) factory image on EU hardware.
However the bootloader does not check this field, making it possible to use
a single sysupgrade image for both hardware.
This patch adds the necessary build bits to generate both EU and US factory
images, and renames the target as "Archer C50v1" since there are as of now
3 different versions of Archer C50 (all with different CPUs).
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The HNET C108
(http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a
mifi based on MT7602A, which has the following specifications:
* CPU: MT7620A
* 1x 10/100Mbps Ethernet.
* 16 MB Flash.
* 64 MB RAM.
* 1x USB 2.0 port. Only power is connected, this port is meant for
charging other devices.
* 1x mini-PCIe slots.
* 1x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.
* 6000 mAh battery.
* 5x controllable LEDs.
Works:
* Wifi.
* Switch.
* mini-PCIe slot. Only tested with a USB device (a modem).
* SIM slot.
* Sysupgrade.
* Button (reset).
Not working (also applies to the factory firmware):
* Wifi LED. It is always switched on, there is no relation to the
up/down state or activity of the wireless interface.
Not tested:
* SD card reader.
Notes:
* The C108 has no dedicated status LED. I therefore set the LAN LED as
status LED.
Installation:
The router comes pre-installed with OpenWRT, including a variant of
Luci. The initial firmware install can be done through this UI,
following normal procedure. I.e., access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to
keep existing settings.
Recovery:
If you brick the device, the C108 supports recovery using TFTP. Keep the
reset button pressed for ~5sec when booting to trigger TFTP. Set the
address of the network interface on your machine to 10.10.10.3/24, and
rename your image file to Kernal.bin.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
In case the link changes from down to up, the register is only updated
on read. If the link failed/was down, this bit will be 0 until after
reading this bit again.
Fixes a reported link down by swconfig alebit the link is up (query for
the link again will show the correct link status)
Signed-off-by: Mathias Kresin <dev@kresin.me>
In conditions where none of the switch ports is connected during boot,
the priv->port[i].link != priv->port[i].phydev->link condition is false
since both link values are equal (false). The carrier of the switch
netdev is never set to off and the link state reported by ip is UNKNOWN.
Turn the carrier off if none of the switch ports has a link, regardless
whether something has been changed. Add a check for a carrier to
prevent unnecessary calls to netif_carrier_off() if the carrier is
already off.
Based on a patch send by Martin Schiller.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 77645ffcd9 ("ramips: add support for the GnuBee Personal Cloud
One") dropped the execution permission from 01_leds with the result
that the file isn't started during first boot and no default LED
configuration is added.
Revert the introduced file permission change.
Fixes: FS#979
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[cherry picked the fix from a board support patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WAN port on the Netgear WNDR4300 router has two LEDs,
amber and green. Use the switch LED trigger to behave as the
rest of the LAN HW controlled LEDs
- Green: 1 Gbps
- Amber: 100/10 Mbps
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
1. Add support to LAN/WAN LEDs attached to ar8327.
2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto)
mode when connected to 10M/100M ethernet.
Signed-off-by: Kuang Rufan <master@a1983.com.cn>
Refresh patches.
Compile-tested on ramips/mt7621 and x86/64.
Runtime-tested on ramips/mt7621 and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This generic structure defines tx_bytes and rx_bytes as unsigned long (u32),
while several devices would typically report unsigned long long (u64).
The code can work as is, but there's a chance that with a sufficiently fast
interface the overflow might happen too fast to be correctly noticed by the
consumers of this data.
This patch makes both field unsigned long long and updates the only known
consumer of this data: swconfig_leds.c
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
The implementation uses a generic callback that select the correct MIB counter
index based on chip version.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch provides a generic switch_dev_ops 'get_port_stats()' callback by
taping into the relevant port MIB counters.
This callback is used by swconfig_leds led trigger to blink LEDs with port
network traffic.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite).
Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi"
They are essentially a single subtarget.
This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* fixes default affinity
* adds a napi watchdog - we were seeing stalled TX queues
* adds up/down locking
Signed-off-by: John Crispin <john@phrozen.org>
Install kmod-rt2800-pci instead of only the rt2x00 library.
Fixes missing wireless interface on AudioCodes AC-MP252.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Neon and vfpv4 support are activated by GCC on all ARMv8 CPUs because
this is now a mandatory part of the architecture. There is not need to
activate is manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for the Comtrend AR-5315u router
This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1
USB host port
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: refreshed patch]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The order of LAN ports shown in Luci is reversed compared to what is
written on the case of the device. Fix the order so that they match.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
This commit adds support for Xiaomi Mi WiFi Router 3G.
Short specification:
- MT7621AT + MT7603EN + 7612EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+2 x 1000M Ethernet
- 1x USB 3.0 port
- reset button
- yellow, blue, red leds
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: mtd erase kernel0
- run: reboot
Originally stock firmware has following partitions:
- ...
- kernel0 (primary kernel image)
- kernel1 (secondary kernel image, used by u-boot in failsafe routine)
- rootfs0 (primary rootfs)
- rootfs1 (secondary rootfs in case primary fails)
- overlay (used as ubi overlay)
This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so
it can be used by LEDE fully for package installation, resulting in 117,5MiB.
This device lacks hw watchdog, so adding softdog instead (stock does the same).
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The Gateworks System Controller (GSC) mimics a standard AD7418 device on
I2C bus 0 at slave 0x29.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refresh patches.
Adapt 704-phy-no-genphy-soft-reset.patch.
Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch.
Compile-tested on brcm2708/bcm2708 and x86/64.
Runtime-tested on brcm2708/bcm2708 and x86/64.
Fixes the following vulnerabilities:
- CVE-2017-7533
- CVE-2017-1000111
- CVE-2017-1000112
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The VoCore2 Lite uses the same PCB as the Vocore2.
This patch moves the common VoCore2 parts into dtsi.
Removed memory node in the device tree source file.
Memory is detected automatically.
http://vocore.io/http://vonger.net/http://vonger.cn/
Specifications:
- SoC: MediaTek MT7688AN
- RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H
- Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG
- Wireless: Built into MT7688AN with onboard IPEX connector
Firmware installation:
- VoCore2-Lite ships with firmware forked from OpenWrt.
- Installation from the bootloader is recommended.
- If using luci/sysupgrade use the -n option (do not keep settings)
original firmware uses a modified proprietary MediaTek wireless driver.
- The wireless is disabled by default in LEDE.
- If reverting to factory firmware using the bootloader is recommended.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Tested by: Noble Pepper <noblepepper@gmail.com>
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.
Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.
Fixes: FS#670
Signed-off-by: Mathias Kresin <dev@kresin.me>
USB doesn't work in some danube boards because otg_cap
is missing since previous changes made on the USB-dwc2
lantiq driver. Fix it.
Tested on the ARV7518PW router.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.
This patch fixes the MAC address for wlan2g in line with OFW.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that
ATM should be used for ADSL and PTM for VDSL.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This makes it possible to simply add additional notification handlers
by putting new scripts in the /etc/hotplug.d/dsl directory.
the following Environment Variables are used:
(values marked with an * are only available when bonding support is
compiled in)
DSL_NOTIFICATION_TYPE with one of these values:
- DSL_STATUS
- DSL_INTERFACE_STATUS
- DSL_DATARATE_STATUS_US
- DSL_DATARATE_STATUS_DS
DSL_LINE_NUMBER=<0|1> *
If DSL_NOTIFICATION_TYPE == DSL_STATUS, these variables are set:
- DSL_XTU_STATUS=<ADSL|VDSL>
- DSL_TC_LAYER_STATUS=<ATM|EFM>
- DSL_EFM_TC_CONFIG_US=<NORMAL|PRE_EMPTION>
- DSL_EFM_TC_CONFIG_DS=<NORMAL>
If DSL_NOTIFICATION_TYPE == DSL_INTERFACE_STATUS, these variables are
set:
- DSL_INTERFACE_STATUS=<DOWN|READY|HANDSHAKE|TRAINING|UP>
- DSL_BONDING_STATUS=<INACTIVE|ACTIVE> *
If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_US, these variables are
set:
- DSL_DATARATE_US_BC0=<Upstream data rate in bit/s for Channel 0>
- DSL_DATARATE_US_BC1=<Upstream data rate in bit/s for Channel 1> *
If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_DS, these variables are
set:
- DSL_DATARATE_DS_BC0=<Downstream data rate in bit/s for Channel 0>
- DSL_DATARATE_DS_BC1=<Downstream data rate in bit/s for Channel 1> *
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Fix when add 'mediatek,cd-poll' to dts cause the sd card be removed randomly.
Special for the device without card-detect pin.
Signed-off-by: Qin Wie <me@vonger.cn>
Use the GPIO dt-bindings macros and add compatible strings in the
ramips device tree source files.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Netgear EX3800 is essentially an EX3700 with a mains output socket.
Both devices use the exact same firmware image (original firmware is named
EX3700-EX3800-version.chk).
This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and
updating the necessary glue.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
This patch cleans up the WN3000RPv3 and EX2700 setup, bringing it in line
with other similar devices:
The power led is a bicolor one. The bootloader brings the red side on at
powerup.
Instead of blinking the red side in diag.sh and need to forcefully turn it off
in 01_leds, this patch simplifies the setup by relying on the default off state
of the gpio-led driver for the red side and blinking the green side as with
other devices.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Cleanup the dtsi files and remove one layer of dtsi. Set the size of
the firmware partition to a value matching the flash size from the
board (variant) name.
Remove the usb led trigger. There is neither a default config for the
usb led trigger nor a LED for usb activity indication.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
So, this is kind of complicated. This has been upstream for a while,
imported from OpenWRT/LEDE with some cleanups. LEDE ramips has stayed
on linux-4.4 this whole time, with the old(er) version of the patch
that had correct behavior[0], while upstream got changed[1].
When LEDE updated to kernel 4.9, the older version of the code from
the patch got replaced with the upstream version containing the bug.
The original behavior, however, seems to be correct here, as the
official programming guide[2] indicates that bit 31 (PDRV_SW_SET)
in register PPLL_CFG1 is reserved, but bit 23 (added as PPLL_LD)
is the PPLL lock state (which also happens to line up with the
error message).
The original confusion probably comes from the double definition
of PDRV_SW_SET[3, 4] in the upstream code, with one correct definition
(31) and one incorrect one (23).
I've also used the opportunity to clean up the error message a bit -
it's still not really helpful to anyone who doesn't already know what
the PPLL is, but at least it's slightly more readable now.
This will probably need to be upstreamed as well, since with the way
it's currently set up, it's unlikely PCI ever worked for anyone who's
running an upstream kernel on that SoC.
[0]: 05d6e92594/target/linux/ramips/patches-4.4/0009-PCI-MIPS-adds-mt7620a-pcie-driver.patch (L259)
[1]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L246)
[2]: http://www.anz.ru/files/mediatek/MT7620_ProgrammingGuide.pdf
[3]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L36)
[4]: 026d15f6b9/arch/mips/pci/pci-mt7620.c (L39)
Signed-off-by: Ilya Katsnelson <me@0upti.me>
01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Luci shows switch ports in wrong order on that device.
This patch fixes switch port numbering and matches them to the device
silkscreen.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
All LEDs GPIOs are active low on this device.
WAN and POWER states were inverted. Add default state for power.
Tested on Archer C50v1.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
With d2b6bf1416 ("ramips: fix image validation errors") the board
name was changed to fix an image validation error. But this change
wasn't applied to all other files using the board name, which broke
sysupgrade.
Revert this change and use the former board name in the metadata
instead.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: FS#735
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Fixes: FS#735
Signed-off-by: Mathias Kresin <dev@kresin.me>
Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix incorrect offset and size of linux partition.
Fixes: 97b36aca09 ("brcm63xx: add pflash for remaining pflash equipped boards")
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The kernel 4.4 patches where already removed with the bump to 4.9. Drop
the the subtarget configs as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.
Specifications:
- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
The square hole is pin 1
The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.
Flash instructions:
You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.
Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.
Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").
Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
