In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.
Hopefully fixes FS#758
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Module definitions for kmod-wdt-sunxi and kmod-eeprom-sunxi are removed
(wdt-sunxi was builtin anyways; nvmem-sunxi, which is the new name of
eeprom-sunxi is changed to builtin). As kmod-eeprom-sunxi was specified
in DEFAULT_PACKAGES, but not available on kernel 4.4, it was breaking the
image builder.
Support for kmod-sunxi-ir is added for kernel 4.4 (it is unclear why it
was disable before, it builds fine with with kernel 4.4).
Condtionals only relevant for pre-4.4 kernels are removed from modules.mk,
as sunxi does't support older kernels anymore.
Fixes FS#755.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It was originally only enabled for the "32" subtarget along with the
"usb" feature which is now also shared by the "64" target
This should fix the phase1 build of armvirt/64
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Do not assign the CPU port twice, this confuses LuCI and possible other
programs relying on topology information in board.json.
Ref: https://github.com/openwrt/luci/issues/1086
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
With update of ARC tools to arc-2016.09 based on GCC v6.x
we have to bump Linux kernel version so both toolchain and
the kernel use the same ARC ABIv4.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
DWC3 driver uses of_usb_get_phy_mode() which is
implemented in drivers/usb/phy/of.c and in bare minimal
configuration it might not be pulled in kernel binary.
In case of ARC or ARM this could be easily reproduced with
"allnodefconfig" +CONFIG_USB=m +CONFIG_USB_DWC3=m.
On building all ends-up with:
---------------------->8------------------
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Building modules, stage 2.
MODPOST 5 modules
ERROR: "of_usb_get_phy_mode" [drivers/usb/dwc3/dwc3.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
---------------------->8------------------
This was affecting Lede in case of CONFIG_ALL_KMODS=y.
The patch is already scheduled for v4.12 and once it is backported to
4.9.y it must be removed from here.
Note this patch makes sense not only for ARC instead it fixes
a generic issue which may affect more arches and platforms thus
putting it in "generic/" folder.
Signed-off-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [patch rename]
Since commit:
7120438e5d
Seems that fsl_rstcr_restart() has been converted
to a reset handler and dropped as hook/callback.
Apply the same to the `tl_wdr4900_v1` target.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Re-applied patches:
001-powerpc-85xx-add-gpio-keys-to-of-match-table.patch
100-powerpc-85xx-tl-wdr4900-v1-support.patch
Dropped patch:
200-spi-fsl-espi-preallocate-local-buffer.patch
now part of kernel upstream hash
1423877b73
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Early SoC versions with an ECO of 1 required the gpio reset.
Mass production SoCs no longer need this work around.
Signed-off-by: John Crispin <john@phrozen.org>
Add the changes suggested by FS#716 to fix the switch driver initialization
on the ZTE Q7.
Also remove the `pinctrl-names` field obsoleted by the changes.
Reported-by: Harry Lau <harrylwc@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fix a copy/paste error and include the ZBT-WE826 dtsi instead of the
ZBT-WG3526 one.
Fix the syntax error in the ZBT-WE826 dtsi to prevent an compile error.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The IMX6 PCIe host controller does not fire legacy interrupts if MSI is
enabled. A patch is being worked on to enable MSI at runtime only when
it is needed but meanwhile this patch will disable MSI for the imx6 kernel.
This fixes the no interrupt issue on cards/drivers that use legacy interrupts
such as ath9k.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Both of these boards share the same DTS, and hardware. The only
difference would be the PCI-E slot, and ath9k card found on the MX60W.
Due to the similarities, it would be more efficient to merge these
profiles.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This moves core router packages to the NAND target, to ensure they are
applied to all images. This change is being done due to an issue found
when flashing the MX60W image, which came without these when built as a
multi image.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The patch 523-MIPS-ath79-OTP-support only supports the OTP offsets for
AR933x chips, which has changed on newer platforms such as the AR934x.
The follwoing change is to add support for reading the OTP on the
AR934x. Tested on an Aerohive AP-121.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
The ZBT-WG826 is available with 16 or 32 MByte of flash. Split the
device tree source file, rename the currently supported 16 MByte
version and add the 32 MByte variant.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Digineo AC1200 Pro is the 32MB flash variant of the ZBT-WG3526 with
unpopulated/exposed sdhci slot. Rename to board to the OEM/ODM name and
add the sdhci kernel module to use it for multiple clones.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ZBT-WG3526 is available with 16 or 32 MByte of flash. Rename the
current supported 16MByte version to indicate which flash size variant
is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specification:
- SoC: MT7621AT, MT7603EN and MT7612EN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 512 MiB (EM6GE16EWXD-12H)
- Ethernet: 1 x WAN (10/100/1000Mbps) and 4 x LAN (10/100/1000 Mbps)
- Others: USB 2.0, micro SD slot, reset button and 8 x LEDs
Issues:
- Two LEDs for 2.4 GHz and 5 GHz Wi-Fi do not work, can't find GPIOs.
- The pwr LED is not GPIO controllable
How to install:
- The original firmware is OpenWrt, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.
Signed-off-by: Jiawei Wang <buaawjw@gmail.com>
The wan port is connected to switch port 0. Fix the mediatek,portmap as
well as the default switch config.
Signed-off-by: Alexey Belyaev <spider@spider.vc>
Make switch port LEDs blink on activity as they do with stock firmware.
The u-boot loader sets suitable values in the LED control register that
unfortunately get blown away by the linux switch driver init. Restore
that value by using driver 'initvals'. 0x0431 is the led control
register, the value 0x0960. Each nybble represents each LED's mode
(LED3,2,1,0) in this case OFF, 1000LINK+Activity, 100/10LINK+Activity,
OFF. Only LED1&2 are physically present.
Enabling the blinkenlights exposed the fact that an RRCP packet was
being emitted by the switch on all ports every second. Further initvals
copied from stock firmware's u-boot driver disabled this 'feature'.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Allow per-device initvals in the DTS file for rlt8366rb
switches.
Shamelessly copies 30494598f8
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Migrate to new image generation and
introduce sdcard generation (based on sunxi).
Profile now generated via image/Makefile instead
of profiles/ directory.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
boardnames were changed with the recent target update. the sysupgrade board
detection was not updated properly.
Signed-off-by: John Crispin <john@phrozen.org>
Without patch unloading the dwc3-of-simple module went stuck after
successfully removing hcd.1 during the hcd.0 removal:
root@LEDE:/# rmmod dwc3-of-simple
[ 21.391846] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.391931] usb usb4: USB disconnect, device number 1
[ 21.397038] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 21.401111] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 21.406685] usb usb3: USB disconnect, device number 1
[ 21.412848] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 21.417248] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 21.422521] usb usb2: USB disconnect, device number 1
followed by nothing.
Sometimes a stall CPU was detected, or a kernel panic,
or a reboot occurred after a couple of minutes.
At the same time unloading the dwc3 module followed by dwc3-of-simple
module was working repeatedly.
root@LEDE:/# rmmod dwc3
[ 53.827328] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.827412] usb usb4: USB disconnect, device number 1
[ 53.832630] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 53.836452] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 53.842314] usb usb3: USB disconnect, device number 1
[ 53.848412] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 53.852542] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.857882] usb usb2: USB disconnect, device number 1
[ 53.863956] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 53.867875] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 53.873696] usb usb1: USB disconnect, device number 1
[ 53.879742] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/# rmmod dwc3-of-simple
root@LEDE:/#
For the non-working case, the code was stuck in a readl() in
http://lxr.free-electrons.com/source/drivers/usb/host/xhci.c#L91
because
http://lxr.free-electrons.com/source/drivers/usb/dwc3/dwc3-of-simple.c#L126
was disabling the wrong clocks when removing hcd.1 (it was disabling
the clock of hcd.0). That's why the readl() went stuck when removing
hcd.0
The patch however addresses the clock assignment from the Netgear R7500
dts file and backs off the previous attempt.
Now unloading and repeated module loading is working just fine.
root@LEDE:/# rmmod dwc3-of-simple
[ 24.089679] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.089765] usb usb4: USB disconnect, device number 1
[ 24.094856] xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered
[ 24.098963] xhci-hcd xhci-hcd.1.auto: remove, state 1
[ 24.104522] usb usb3: USB disconnect, device number 1
[ 24.111194] xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered
[ 24.115086] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.120396] usb usb2: USB disconnect, device number 1
[ 24.126503] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 24.130347] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 24.135948] usb usb1: USB disconnect, device number 1
[ 24.142085] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
root@LEDE:/#
Fixes: dwc3-of-simple module unloading for Netgear R7500
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The patch follows the qualcomm code comments setting
SSUSB_CTRL_TEST_POWERDOWN to 0x1 and is testing and clearing the
bit during USB superspeed PHY init. According to Andy Gross it
needs to be BIT(26).
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes Ethernet<->WiFi bridge for Raspberry Pi and probably other devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
