* The left most mini-PCIe slot (the one attached to SIM2) can be
power-cycled by setting GPIO 0 to high/low.
* The D240 only needs the MT76x2 module, so update makefile to reflect this.
Note that until the default mt7620 target is updated, then kmod-mt76 (and thus
kmod-mt7603) will be selected by default.
v2->v3:
* Indentation error.
v1->v2:
* Rename gpio and remove redundant comment (thanks Piotr Dymacz)
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block.
And, we remove kmod-sdhci dependence assignment from all related target devices.
Signed-off-by: Furong Xu <xfr@outlook.com>
Change dts file to add default sata trigger to sata led.
Backport upstream accepted patch to add sata trigger to device tree
source files already upstreamed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[backport upstream accepted patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ASL56026 is a VDSL2 router with dual 100mbit ethernet,
also known as the ECI B-FOCuS V-2FUb/I.
CPU: Lantiq XRX268 v1.1 at 333MHz
Modem: Lantiq VRX208
RAM: 32MiB DDR2 at 167MHz
Flash: 8MiB NOR, Spansion S29GL064N90TF04
UART is at JP1:
Pin 1 TX
Pin 2 GND
Pin 3 +3.3V
Pin 4 NC
Pin 5 RX
Boot selection pins are exposed via several resistor jumpers:
boot_sel0 is at J15, on the rear of the board. Default is high.
boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low.
boot_sel2 is at J12, directly below the SoC. Default is low.
boot_sel3 is at J16, on the rear of the board. Default is low.
The boot_sel pins should never be shorted, the jumper must be moved or
a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work)
To install with the stock bootloader you must break the built in image selection process
which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion
This is done by setting loadaddr and both f_upgrade_addr vars to the same address:
VR9 # setenv loadaddr 0xB0040000
VR9 # setenv f_upgrade_addr 0xB0040000
VR9 # setenv f_upgrade2_addr 0xB0040000
VR9 # saveenv
Then flash the firmware image:
VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin
VR9 # erase B0040000 +${filesize}
VR9 # cp.b 0x81000000 0xB0040000 ${filesize}
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
This backports fixes for setting of_node and making it possible to read
extra info from DT. This was partially fixed by:
[PATCH] leds: leds-gpio: Set of_node for created LED devices
but it didn't work during initialization.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Open-code usb_phy_generic_register instead of calling it, since it is
really trivial. Avoid pulling CONFIG_NOP_USB_XCEIV into the kernel
config and add a proper dependency instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The malta "be" and "le" subtargets share the arch with many devices of
ar71xx and ramips. They can be handy for testing, debugging, trying
both snapshot and release builds.
This commit makes the "be" subtarget part of the ci and release builds
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
As usual these patches were extracted and rebased from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.9.y
- Remove led1 from diag.sh for RPi3 since it causes boot issues.
- Fix modules.mk typos.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Bump kernel from 4.4.50 to 4.4.52
Refresh patches
Compile tested all 4.4. targets
Run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
These modules are not needed by the EX2700, since it does not
have an external wifi chip (MT7620A is covered by rt2x00).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
This device features both a 2.4 and 5Ghz radio, and supports
802.11a/b/g/n/ac modes.
It has 5 Gb-Ethernet ports and a USB 3.0 host port.
It is powered by the Mediatek MT7621 SoC, and the MT7602E and MT7612E wifi
chipsets, together with 128MB of RAM and 16 MB of SPI Flash.
The stock firmware is in fact based on some openwrt barrier breaker, with a
mediatek SDK kernel, and an afoundry custom made web interface (not LuCI
based).
Firmware update page on the stock web interface can not accept sysupgrade
images, it bricks the device.
At this point, the only working solution I found was to connect to the
serial console port (available on J4 header) and to use opkg to install
dropbear.
Then scp the sysupgrade file in the device's /tmp and run sysupgrade from
console without preserving configuration files.
Signed-off-by: Francois Goudal <francois@goudal.net>
Somewhere between 4.4 and 4.9 there was a change that made
OF_EARLYCON_DECLARE adding entries to the __earlycon_table instead of
__earlycon_of_table. We need to keep this table as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This driver has been added instead of improving spi-bcm53xx. It has some
advantages: allows SPI speed control & hopefully doesn't have bug that
was stopping us from using multiple SPI messages for writing flash data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
the mtd_get_mac_ascii function called within this script requires the inclusion of /lib/functions/system.sh
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This patch adds supports for the HiWiFi HC5962(gee4) http://www.hiwifi.com
Short specification:
- MT7621AT + MT7612EN + 7603EN
- 256MB DDR3 RAM
- 128MB NAND flash
- 1+3 x 1000M Ethernet
- 1x USB 2.0 port. 1x USB 3.0 port.
- reset button
- UART pad on PCB (JP3: TX, RX, GND, 3.3V)
Flash instruction:
1, Download lede-ramips-mt7621-hc5962-squashfs-factory.bin
2, Login as root via SSH on 192.168.199.1 and then copy factory.bin(using wget or nc or...) to /tmp/
3, use the following commands:
$ mtd write /tmp/lede-ramips-mt7621-hc5962-squashfs-factory.bin firmware
$ mtd erase firmware_backup && reboot
After reboot you should be able to login as root via SSH on 192.168.1.1
Signed-off-by: ZengFei Zhang <zhangzengfei@kunteng.org>
Fixes the following build error:
CC arch/mips/boot/compressed/decompress.o
OBJCOPY arch/mips/boot/compressed/vmlinux.bin
XZKERN arch/mips/boot/compressed/vmlinux.bin.z
OBJCOPY arch/mips/boot/compressed/piggy.o
LD vmlinuz
arch/mips/boot/compressed/decompress.o: In function `lzma2_lzma':
/tmp2/mehrtens/linux/arch/mips/boot/compressed/../../../../lib/xz/xz_dec_lzma2.c:884: undefined reference to `memmove'
make[1]: *** [vmlinuz] Error 1
make: *** [vmlinuz] Error 2
lib/decompress_unxz.c only defines its own memmove function if there is no
macro with the same name.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add SPROM wifi to the kernel board data.
After this fix, the wifi won't work anyway due the lack
of RAM memory (16 MB). It will throw a kernel panic
when loading the b43 drivers.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Fix the register for configuring rising/falling edge
Rising should be sense=1, and falling sense=0.
The old driver used these values, but the new one have
them flipped.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
