While rt288x only has a MIPS 4KEc processor, it implements the MIPS32r2
architecture just like the 24Kc, so the instruction set should be 100%
compatible.
Switching it to 24kc allows it to share the package architecture with a
lot of other targets instead of creating a special case, saving
buildbot resources.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support Abicom International Scorpion SC450 Board
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB NAND Flash
16MB NOR Flash
10/100/1000 Ethernet
15W Max, 3x3 Mode, Full Power TX Power
802.3-at POE+ & DC Input options
100x 85mm
USB
PCIe
SFP
GPIO/LED
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Support Abicom International Scorpion SC300M Module
QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Changes the platform to use the Chipidea driver instead of the
generic USB host driver which has support for both host and
device modes (selected on boot).
The changes in 930-chipidea-pullup.patch are already in mainline.
I'll upstream 920-usb-chipidea-AR933x-platform-support.patch once I
can test the changes with a newer kernel.
Signed-off-by: Svetoslav Neykov <svetoslav@neykov.name>
erlite mtdparts exposes boot0, boot1 and eeprom regions
as read/write.
this patch adds readonly flags, so these regions can't be
modified. same as it is already for ER profile.
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Disabling ethernet during reboot (only to enable it again when the
ethernet driver attaches) can put the chip into a faulty state where it
corrupts the header of all incoming packets.
This happens if packets arrive during the time window where the core is
disabled, and it can be easily reproduced by rebooting while sending a
flood ping to the broadcast address.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since the MIPS IRQ stack patches, lantiq devices were emitting a storm
of messages like this:
[ 567.872172] Spurious IRQ: CAUSE=0x1100c300
Fix this by reworking the IRQ dispatch code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The soft_config partition must be writeable for rbcfg to be able to
enact changes to the routerboot configuration.
The read-only flag was a mistake in the initial patch. Removing it
brings mach-rb941.c in line with all other RB platforms.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band.
However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading.
This patch adds d7800 to ath10k caldata extraction list.
I can get two functional wireless bands after making change to it.
Signed-off-by: Zhang Jingye <934526987@qq.com>
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
This change adds the sp5100_tco driver as a kernel module for the x86
target. Specifically, this can be used by the PCEngines APU2/APU3. The
reason for having this as a kernel module is to allow users to
load/unload it on demand, as the I2C interface on the APU2/APU3 will not
work while this module is loaded. More info can be found on GitHub at
https://github.com/riptidewave93/LEDE-APU2/pull/5#issuecomment-255667736
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This adds the following patches to the x86 target:
sp5100_tco: Add AMD Mullins platform support
sp5100_tco: Add AMD Carrizo platform support
sp5100_tco: fix the device check for SB800 and later chipsets
watchdog: sp5100_tco: properly check for new register layouts
With these added, the sp5100_tco driver can then be used on newer AMD
platforms, such as the PCEngines APU2/APU3 boards.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Mikrotik RB411U has only one ethernet port - eth0. This patch allows to create
correct config with one lan section.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Add full support for Mikrotik RB-941-2nD (hAP lite)
Original patch by Sergey Sergeev <adron@yapic.net> and
more information is available here:
https://wiki.openwrt.org/toh/mikrotik/rb941_2nd
I updated and adapted the patch to apply cleanly to LEDE trunk
and added proper numbering for the switch ports (matching case
labels).
Tested working on actual hardware with the information
provided in the above webpage. Sysupgrade works.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.
There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Running ar8327_get_arl_entry() early after boot leads to MDIO related system
lockups on several devices using this driver.
Since dumping the ARL table contens is an optional, uncritical feature, simply
disable the code for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes hangs in igb that happen if the update call interrupts an
already existing dev_get_stats call. In that case the calling CPU
deadlocks because it's trying to acquire the same spinlock recursively.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This specifies wireless limitations for Netgear R8000 making sure people
won't use channels incorrectly (limited performance). There are also 2
new DTS files not used by us yet.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
At the moment we have 2 seperate device tree sources: 1 for ipq8064 soc located
in kernel source and 1 custom in LEDE for ipq8065.
ipq8064 and ipq8065 SoCs are completely identical except ipq8065 has higher cpu
frequencies and adjusted corresponding power supply.
This commit makes ipq8065 DTS to contain only specific for ipq8065 DT entries while
pulling all the basic SoC stuff from ipq8064 DTS.
It makes easier to manage ipq806x device trees and instead of committing changes into
2 seperate equal DTS we are ending up with only 1.
It also enables ipq8065 devices to automatically receive changes made in upstream kernel.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
According to Qualcomm SDK usb3 phy suspend should be disabled for
ipq806x.
This may solve issue on some ipq806x devices that breaks usb3
storage peripherals during system boot.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)
Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
- RAM: 64MB DDR
- Storage: 16MB NOR SPI flash onboard
- Omega2+
- RAM: 128MB DDR
- Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
- All Docks Provide:
- Micro-USB port to provide power to the Omega
- On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
- USB 2.0 socket connected to Omega
- Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
- Omega GPIO breakout
- Allows for connection of Omega Expansions:
- Ethernet Expansion
- Relay Expansion
- PWM Expansion
- OLED Expansion
- Ethernet Expansion
- Proto Expansion
- Cellular Expansion
Signed-off-by: Lazar Demin <lazar@onion.io>
I made a commit that added the RTC driver to the kernel config with
the intent that it would fix hctosys. Unfortunately while the RTC
driver is in there, it's connected through I2C, the driver for which
comes in module form and is thus loaded late. After this commit, it
works fine.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Prevents crashes when IRQs arrive when the current kernel stack context
already contains deeply nested function calls, e.g. when stacking lots
of network devices on top of each other
Signed-off-by: Felix Fietkau <nbd@nbd.name>
