glibc is moving to remove the include of sys/sysmacros.h from
sys/types.h, and some distros have done this early. Other libcs may
already lack this include. Include sysmacros.h explicitly.
Fixes: FS#1015
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
[refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
glibc is moving to remove the include of sys/sysmacros.h from
sys/types.h, and some distros have done this early. Other libcs may
already lack this include. Include sysmacros.h explicitly.
Fixes: FS#1016
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch moves build_fw() to mktplinkfw-lib.c
The versions of mktplinkfw.c and mktplinkfw2.c had slight
differences in code flow, the version from mktplinkfw.c has been
preferred.
While it's expected that this change will not affect mktplinkfw2,
all use cases could not be tested and so this particular change
is committed separately.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This patch carves out the duplicated code of mktplinfw.c and
mktplinkfw2.c and moves it to mktplinkfw-lib.c
This change is a semantic NOP (the code is unchanged).
To ensure compatibility with gcc-5.x and newer without changing
the code, -fgnu89-inline is added to the build flags for these
two binaries.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This patch removes all the hardcoded board-specific values from
mktplinkfw2.c, and as well as the corresponding support code.
By design, this change also deletes all of the broken matching logic
that was embedded in mktplinkfw2 and aligns the "inspect" behavior
with that of mktplinkfw (i.e. print the parsed header content as
they are without further processing).
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fix segmentation fault caused by implicit declaration of function 'reallocarray'. Added patch will enable
reallocarray() prototype in glibc 2.26+ on Linux systems. This fix will be included in flex 2.6.5.
Fixes LEDE issue: FS#1003 (Flex does not build with GCC 7.2)
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Update e2fsprogs to 1.43.6
* Remove FreeBSD patch as it's not needed, FreeBSD 9.1 is EoL and this
is compiling on FreeBSD 11.1.
* Remove libmagic patch, RHEL 5 is EoL (End of Production Phase) since
March 31, 2017.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TP-Link Archer C20 v1 is a router with 5-port FE switch and
non-detachable antennas. It's very similiar to TP-Link Archer C50.
Also it's based on MediaTek MT7620A+MT7610EN.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 8x LED (GPIO-controlled*), 2x button, power input switch
- 1 x USB 2.0 port
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the blue part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
work.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash. So, to flash this device we must
to prepare image using original firmware from tp-link site with uboot.
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot.
There are two ways to flash the device to LEDE:
1) Using tftp mode with UART connection and original LEDE image
- Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp
server directory
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, power up the router and press
key "4" to access U-Boot CLI.
- Use the following commands to update the device to LEDE:
setenv serverip 192.168.0.66
tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
- After that the device will reboot and boot to LEDE
2) Using tftp mode without UART connection but require some
manipulations with target image
- Download and unpack TP-Link Archer C20 v1 firmware from original web
site
- Split uboot.bin from original firmware by this command (example):
dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1
- Create ArcherC20V1_tp_recovery.bin using this command:
cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin
- Place ArcherC20V1_tp_recovery.bin in tftp server directory.
- Configure PC with static IP 192.168.0.66/24 and tftp server.
- Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
- Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Update (lib)expat to 2.2.3
Remove poor entropy hack, 2.2.3 uses /dev/urandom in worst case
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
When -e option it specified a corresponding flag is set in the
custom_board. By using custom_board as fallback -e option gets respected
for unknown boards.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
As we can now use combined mode in "mktplinkfw" tool to generate the
same header/image, this tool is no longer needed.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
We use combined option in "mktplinkfw" tool for generating initramfs
kernel images and header for kernel inside "safeloader" image type (in
fact, only for TL-WR1043ND v4 at this moment).
There is also "mktplinkfw-kernel" tool, a stripped-down version, used
only for generating "simple" header, for safeloader image types.
This changes how "mktplinkfw" handles combined images (which then will
allow us to drop the stripped-down version of the tool):
- drop "ignore size" command line option (it was used only for combined
images anyway)
- don't require "flash layout id" for combined images (we don't need and
shouldn't limit size of the initramfs kernel and for kernels inside
safeloader images, the "tplink-safeloader" tool does the size check)
- require kernel address and entry point in command line parameters for
combined images (consequence of previous point)
- don't include md5 sum and firmware length values in header (they are
needed only for update from vendor GUI and are ingored in case of
initramfs and "tplink-safeloader" images)
- drop "fake" flash layout for TL-WR1043ND v4 as it's no longer needed
Also, adjust "mktplinkfw-combined" command in ar71xx/image/tp-link.mk to
match introduced changes in "mktplinkfw" tool.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Expat release 2.2.2 requires support for either syscall(SYS_getrandom) which
is available on Linux 3.17 or support for getrandom() which is only available
in glibc 2.25 or later.
Since some of our builders still run on Linux 3.16, we need to forcibly
disable the use of getrandom() for the host builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This was already done in commit 91e262c6b3 ("tools: flex: fix build
with automake 1.15.1")
This reverts commit 6b127d8639.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit fixes build factory image for TP-Link Archer C60v1.
Size of partition "SupportList" is only 256 bytes, and can
contain only 3 entries.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
It seems simpler to store all custom (command line set) option values in
a struct identical to the predefined ones. It doesn't require:
1) Having so many global variables
2) Copying data from the predefined boards
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
After the update of GNU automake, the flex configure fails with
configure.ac:31: error: version mismatch. This is Automake 1.15.1,
configure.ac:31: but the definition used by this AM_INIT_AUTOMAKE
configure.ac:31: comes from Automake 1.15.
Apply the autoreconf host fixup to properly regenerate configure before
to avoid triggering the version mismatch. Also refresh the patch while
we're at it.
Fixes FS#885.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds command line option in "mktplinkfw" tool for endianness swap
in kernel load address and entry point fields. As in "mktplinkfw2" tool,
we will need this for little-endian targets, like "ramips".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
Root access over serial line in vendor firmware: root/sohoadmin.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
LEDE supports few devices using TP-Link firmware format (V2 or V3):
ArcherC20i, ArcherC50, ArcherMR200, TDW8970, TDW8980, TL-WR840N v4,
TL-WR841N v13 and VR200v
Testing mktplinkfw2 tool with official (vendor generated) firmware files
for above devices has shown an error when comparing calculated and
included MD5 sum, e.g.:
> mktplinkfw2 -i Archer_C20iv1_0.9.1_3.2_up_boot\(170221\)_2017-02-21_17.14.03.bin | grep -A 1 MD5Sum1
Header MD5Sum1 : 22 5a cb 92 10 d2 95 7b df 62 9a f8 62 17 37 10 (*ERROR*)
--> expected : ad 19 11 d1 78 98 a7 42 5f 2e 64 da 8a 34 ec cb
This problem has been verified to occur with:
Archer_C20iv1_0.9.1_3.2_up_boot(170221)_2017-02-21_17.14.03.bin
Archer MR200v1_0.9.1_1.1_up_boot_v004a.0 Build 160905 Rel.60037n.bin
TD-W8970v3_0.9.1_2.0_up_boot(160816)_2016-08-16_10.40.57.bin
TD-W8980v1_0.6.0_1.8_up_boot(150514)_2015-05-14_11.16.43.bin
Archer_VR200vv2_0.2.0_0.8.0_up_boot(161202)_2016-12-05_14.39.06.bin
For some images, e.g.:
Archer_C50v3_EU_0.9.1_0.3_up_boot[170417-rel52298].bin
TL-WR840Nv4_EU_0.9.1_4.16_up_boot[170421-rel70692].bin
TL-WR841Nv13_0.9.1_3.16_up_boot(161012).bin
mktplinkfw2 calculates zero MD5 so these has to be fixed separately:
> mktplinkfw2 -i TL-WR841Nv13_0.9.1_3.16_up_boot\(161012\).bin | grep -A 1 MD5Sum1
Header MD5Sum1 : 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 (*ERROR*)
--> expected : 6f 1d 9b 57 5d 42 14 6d bf a2 03 9d 46 7d 55 55
It's most likely that MD5 salt used in mktplinkfw2 has been always wrong
(and it's not a matter of e.g. a vendor change). Update it to fix MD5
calculation.
This has been also verified to calculate MD5 correctly for other (not
yet supported) devices, e.g.:
Archer_C3150v2_0.1.0_0.9.1_up_boot(160812)_2016-08-12_10.52.54.bin
Archer_C3200v1_0.9.1_0.1_up_boot(160704)_2016-07-04_15.48.28.bin
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Mathias Kresin <dev@kresin.me>
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As it turned out, some of new MediaTek based TP-Link devices use value
from field at 0x3c offset in version 3 of TP-Link header to specify
"Additional Hardware Version".
Value from this field is validated during regular (GUI) firmware upgrade
on devices like TL-WR840N v4 or TL-WR841N v13. If it's zero (based on
some tests, it seems that firmware will accept anything != 0), errors
like below are printed on console and upgrade fails:
[ rsl_sys_updateFirmware ] 2137: Firmware Additional HardwareVersion
check failed
[ rdp_updateFirmware ] 345: perror:4506
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)
QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.
Flash instruction:
Use "factory" image directly in vendor GUI.
Recovery method:
1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server.
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset
This commit is based on GitHub PR#1112
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Federico Cappon <dududede371@gmail.com>
The sum variable need to be initialised, otherwise it will points to
random stack memory and a bogus image checksum might be calculated.
While at it, fix the segfault in case the product region code isn't
specified and enable compiler warnings which had revealed all the code
issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the timestamp from the enviroment SOURCE_DATE_EPOCH
if set instead of the build time.
Fixes reproducible builds for certain firmware images.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This adds the necessary firmware layout definitions for the Archer C25.
It has an addtional partition containing some static data ("extra-para")
without which no factory flash is possible, therefore put_data() has been
added.
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on
Qualcomm/Atheros QCA9561.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x USB 2.0
- 11x LED (most are controlled by 74HC595)
- 2x button
- UART header on PCB*
* Serial console is disabled in OEM non-beta firmwares and corresponding
GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by
production (non-beta) U-Boot and firmware.
Currently not working:
1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs
by some U-Boot versions.
Flash instruction under vendor GUI:
1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin".
2. Go to WEB interface and perform usual firmware upgrade.
FLash instruction under U-Boot recovery mode (doesn't work in beta
firmware):
1. Setup PC with static IP "192.168.0.66/24" and tftp server.
2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make
it available to download from your tftp server.
3. Press "reset" button and power up the router, wait till "WPS" LED
turns on.
Flash instruction under U-Boot, using UART (can be done only with
preinstalled UART-enabled U-Boot version!):
1. Use "tpl" to stop autobooting and obtain U-Boot CLI access.
2. Setup ip addresses for U-Boot and your tftp server.
3. Issue below commands:
tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b 0x81000000 0x9f020000 $filesize
reset
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
[minor code style fixes, extended commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Some TP-Link routers (C25, C59, C60) contain a version string instead
of a binary structure in the soft_version partition.
Flashing LEDE from the original firmware's GUI, this version string
taken from the soft_ver partition of the firmware image is written to
the router's config partition.
When using tftp recovery to go back to the original Archer C25 firmware,
a version check compares that version to the version of the firmware to
be flashed.
Without proper contents in the config partition, reverting to the
original firmware fails.
Therefore, write the string "soft_ver:1.0.0\n" to that soft_ver
partition.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Build broke as distributions now include Perl 5.26 and automake
triggered an "Unescaped left brace in regex" error.
Import upstream commit 13f00eb449 to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On Linux, symlink permissions cannot be altered and are always 0777.
On Mac OS X they can be 0755. Force 0777 here to keep tarballs
reproducible across systems
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Seems to be useful only for old and unsupported operating systems. Removed and adjusted the mtd-utils Makefile.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Remove upx from repo, it hasn't been used for a very long time and serves little to no purpose.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update to 4.1
Remove 0001-mkfs-Default-to-64-32-heads-sectors-for-targets-smal.patch
as it's included in upstream repo.
Refresh patch
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update from 3.3.2 to 3.3.4 & refresh patches.
Remove 110-disable-assembler-support as ccache now understands the
'.incbin' directive.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB
Flash instruction: use "factory" image directly in vendor GUI.
Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.
You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin
Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.
Available FLASH space, with LEDE trunk, is only 240 KB.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* Update to 1.43.4
* Refresh patches
* xz tarball which saves about 2M in size
Changelog: http://e2fsprogs.sourceforge.net/e2fsprogs-release.html#1.43.4
Tested by Etienne Haarsma (ar71xx), Daniel Engberg (kirkwood)
Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com>
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [use @KERNEL instead of harcoded URL]
samba.org has started to enforce https and
currently plain http downloads with curl/wget fail,
so convert samba.org download links to use https.
Modernise links at the same time.
Also convert samba.org URL fields to have https.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
some of Buffalo DHP series use slightly different trx magic, buffalo-enc,
buffalo-tag, and factory image begin with 'bgn'.
this patch adds support for building those images.
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
Qemu's local AES code defines symbols that conflict with
LibreSSL/OpenSSL's libcrypto. Rename them to avoid build problems.
See upstream commit c8d70e59738e672021926c7747af8ef9dea15c82.
Fixes FS#444.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB
TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")
Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Admittedly, this is my own OCD wanting to get rid of this.
Because I tried (a while back to upgrade QEMU to a newer version),
and (during that attempt) I tried to get rid of this.
Tested on Linux & Mac.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The final semantic is the same, but this is a bit more correct.
Build tested on Windows 10 (yes, there is some
Ubuntu mode for Windows 10, and I've been also building LEDE
on it for a few weeks).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This should hopefully fix build issues where libraries that we ship in
tools/ were accidentally picked up from other places on the system, e.g.
/usr/local
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Patch cmakes cmcurl component to unconditionally link librt when we discover
a clock_gettime() symbol in -lrt.
This is required to sucessfully link LibreSSL's libcrypto which might or
might not reqauire librt.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Since linker argument order is significant on modern host compilers, pass
the required libcrypto libraries through the HOST_LOADLIBES variable in
order to ensure proper order of the final linker command line.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Fixes link errors for host packages like ruby like the following:
/usr/bin/ld: .../staging_dir/host/lib/libcrypto.a(libcrypto_la-md5_dgst.o):
relocation R_X86_64_PC32 against symbol `memcpy@@GLIBC_2.14' can not be used when making a shared object; recompile with -fPIC
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
A lot of packages (especially those using libtool) depend on sed being
available. xz fails on an incremental build pretty early if it's not
there.
Clean up handling if essential core tools (patch, tar, xz), build them
in parallel and make them depend on sed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Funnel the required LDFLAGS environment through HOST_CONFIGURE_CMD for now
as the HOST_CONFIGURE_VARS semantics are completely broken.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
LibreSSL's libcrypto.so has an indirect dependency to librt for clock_gettime()
on Linux.
Use pkg-config to portably discover the required linker flags.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
LibreSSL's libcrypto.so has an indirect dependency to librt for clock_gettime()
on Linux.
Use pkg-config to portably discover the required linker flags.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Ensure that pkg-config is available before building libressl as we're going
to need it for setting proper link flags in utilities requiring libcrypto.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
graphite is disabled by default and it's not worth carrying ppl and
cloog for supporting this feature on the old gcc 4.8, which is only used
for ARC
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
The TL-WR1043ND v4 uses a kernel image with a mktplinkfw header inside the
os-image partition of a tplink-safeloader image.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In order to make it easier to add new boards in the future, refactor the code
to describe the image layouts of supported boards in a struct array and alter
the image generation routines to figure out the sysupgrade partitions
automatically.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Force root/root as names for uid0/gid0 instead of using the system
names. This helps make packed download tarballs more reproducible
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is intended to be used for a wide array of package sanity checks.
The first check that is implemented is for the hash of downloaded files.
It checks:
- Missing hash
- Use of SHA256 instead of MD5
- dl/<file> hash not matching hash in makefile
- deprecated MD5SUM variable
The deprecated MD5SUM variable check is skipped for feeds/ until OpenWrt
is updated as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Adds support for new EU and US variants; removes a few strings that were
never actually used and have been removed from the stock firmwares.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Sadly, LibreSSL claims to be OpenSSL v2.0.0 while not providing the new
interfaces introduced with OpenSSL v1.1.x, so extend the pre-OpenSSL 1.1.x
compat checks to consider LibreSSL as well.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The OpenSSL 1.1.x version series undergone some major API changes which made
the RSA structure opaque and deprecated a number of methods, so add some
conditional compat code to make the u-boot source build again.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Our current implementation is pretty old and uses some pre-standard/old
ANSI C style that triggers warnings like:
warning: call to function 'MD5_Init' without a real prototype [-Wunprototyped-calls]
This is caused by declarations specified in a following way:
src/md5.h:60:6: note: 'MD5_Init' was declared here
void MD5_Init ();
Having these warnings makes it harded to notice real problems. We could
try hiding them but it makes more sense to just use a cleaner code.
Another tiny gain from this switch is slightly reduced binary size, on
x86_64 tplink-safeloader's size 48104 became 48003.
The new code is public domain, uses "heavily cut-down BSD license".
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Earlier compilers such as GCC 4 do not like anynomous unions, make it a named
union "u", and update the code where relevant.
Fixes FS#298
Fixes: a72e1692b8 ("firmware-utils: Add support for the Cisco Meraki MX60/MX60W")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
User-visible changes since 0.64 are as follows:
- Translation fixes
- Project settings have priority
- Reject binary files in patches
- Fix a race condition in diff_file
- Performance: Optimizations to the setup command
- Performance: Optimizations to the bash completion script
- Test suite: Improve the edit test case
- Test suite: Make the symlink test more robust
- Test suite: Test backup failure
- Test suite: Test the header command with hard links
- diff: Report diff failures
- edit: Fix a corner case bug
- mail: Fix the help text
- push: Fix the synopsis
- refresh: Do not remove symlinks
- refresh: Break links to read-only patch files
- refresh: Always preserve modification time
- setup: Report failed look-ups in inspect-wrapper
- quilt.el: Fix quilt-editable when patches are stored in subdirs
- bash_completion: Handle spaces in file names
- bash_completion: Update the list of commands
- bash_completion: Add new command options
- bash_completion: Fix handling of mail, new, push options
- guards: Simplify the help text
- guards: Include the file name also in the "Not found" case
- guards: Add support for an external filelist in --check mode
- guards: Report which config file has problem in --check mode
- guards: Documentation update
- guards: Clarify a user message
Note to packagers: the Makefile was modified to take configure's
--sysconfdir into account as other projects do. As a result, setting
--prefix=/usr will no longer put the configuration files under /etc.
You now need to explicitly pass --sysconfdir=/etc. If you don't,
configuration files will go under /usr/etc, which is not what you want.
This is somewhat less intuitive, but also more consistent with what
other projects are doing.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
RELEASE 2.5.1 - Mon, 03 Nov 2016 13:37:42 -0400
- Add scons-configure-cache.py to packaging. It was omitted
- Use memoization to optimize PATH evaluation across
all dependencies per node.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This patch adds header support for the Cisco Meraki MX60/MX60W, which
are a part of the apm821xx target. Some structure changes were needed
due to the fact this device uses U-Boot (unlike other devices in
mkmerakifw.c) which uses a different header structure to define the load
offsets for the image.
A thanks to Christian for helping implement this properly.
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Recent refactoring introduced a regression. It ignored second argument
of make_support_list function which was originally true for C2600. The
new generic build_image function always passes false.
This patch allows specifying trailing char in a device specific info. It
also switches Archer C9 to the \0 char to make it compliant with vendor
images.
I verified generated images to be binary identical to the ones that
were created before whole refactoring.
Reported-by: Jo-Philipp Wich <jo@mein.io>
Fixes: fd924d2068 ("firmware-utils: tplink-safeloader: use one function for generating images")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Looking into /usr/include/stdlib.h, there's a `devname()` function defined
under some #ifdef's which conflicts with the `static char *devname` definition
in `src/mkwrggimg.c`.
Defining `_ANSI_SOURCE` in the `src/mkwrggimg.c` file, omits that part of the
header.
Another more intrusive approach is to rename `devname` to something like
`g_devname` in `src/mkwrggimg.c`. But I think the `_ANSI_SOURCE` define should
be enough.
Compilation error is:
src/mkwrggimg.c:64:14: error: redefinition of 'devname' as different kind of symbol
static char *devname;
^
/usr/include/stdlib.h:286:7: note: previous definition is here
char *devname(dev_t, mode_t);
^
src/mkwrggimg.c:147:12: error: non-object type 'char *(dev_t, mode_t)' (aka 'char *(int, unsigned short)') is not assignable
devname = optarg;
~~~~~~~ ^
src/mkwrggimg.c:192:6: warning: comparison of function 'devname' equal to a null pointer is always false [-Wtautological-pointer-compare]
if (devname == NULL) {
^~~~~~~ ~~~~
src/mkwrggimg.c:192:6: note: prefix with the address-of operator to silence this warning
if (devname == NULL) {
^
&
src/mkwrggimg.c:251:27: warning: incompatible pointer types passing 'char *(dev_t, mode_t)' (aka 'char *(int, unsigned short)') to parameter of type 'const char *' [-Wincompatible-pointer-types]
strncpy(header->devname, devname, sizeof(header->devname));
^~~~~~~
/usr/include/secure/_string.h:119:34: note: expanded from macro 'strncpy'
__builtin___strncpy_chk (dest, src, len, __darwin_obsz (dest))
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
[Jo-Philipp Wich: slightly reformat commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
