Commit graph

14444 commits

Author SHA1 Message Date
Felix Fietkau
061d516d43 ar71xx: Add pll_1000 value for eth0 to Ubiquiti Rocket M XW
This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45965
2015-06-14 17:43:18 +00:00
Felix Fietkau
c41a1affb8 oxnas: change file extension of u-boot+initramfs image
The *u-boot-initramfs* images are not ITB/FIT images but are rather
supposed to be loaded to RAM and jumped-into.
To avoid confusion, change the file extension from itb to bin.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 45963
2015-06-14 17:42:00 +00:00
Felix Fietkau
008a0ebc56 ar71xx: fix mac offset in firmware file
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes #19751, bug introduced in #45624

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 45958
2015-06-14 17:41:27 +00:00
Felix Fietkau
28d8972c25 ar71xx: fix 100/10mbps ethernet link issues on mynet range extender
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.

The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.

The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.

Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 45954
2015-06-14 17:41:01 +00:00
Jonas Gorski
84bfed7bd3 brcm63xx: fix A4001N image padding size
When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.

Fixes #19836.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45945
2015-06-11 12:10:43 +00:00
Rafał Miłecki
950c0191c2 bcm53xx: update NVRAM driver to MIPS version from upstream-sfr
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45943
2015-06-10 20:34:32 +00:00
Rafał Miłecki
b273bb1896 brcm47xx: backport BCM47XX patches (NVRAM & BCMA_HOST_PCI)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45942
2015-06-10 19:52:07 +00:00
Jonas Gorski
9fbd6d0ba0 b53: fix memory out of bounds access on 64 bit targets
On device reset the sizes for the vlan and port tables were wrongly
calculated based on the pointer size instead of the struct size. This
causes buffer overruns on 64 bit targets, resulting in panics.

Fix this by dereferencing the pointers.

Reported-by: Fedor Konstantinov <blmink@mink.su>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45938
2015-06-10 09:21:36 +00:00
Jonas Gorski
d24d5412ff b53: widen stp state mask to 3 bits (instead of 2)
At least on my b53 chip, the mask is 3 bits wide, and because
of this some STP states are not set properly and discarded when read.

Maybe for some other chips it makes sense to have just 2 bits width,
but I don't have other versions around to test/validate.

If that's the case then maybe we could add another STP state mask.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45937
2015-06-10 09:21:31 +00:00
Felix Fietkau
d5542640d4 ramips: fix Power LED handling for WHR-300HP2, WHR-600D, WHR-1166D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45930
2015-06-08 12:51:13 +00:00
Rafał Miłecki
a1340b5cce kernel: backport config-related bcma patches from 4.2
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45927
2015-06-08 12:49:54 +00:00
Rafał Miłecki
e011a5c375 bcm53xx: backport the latest 4.2 ARM BCM5302X patches
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45922
2015-06-07 14:41:05 +00:00
Rafał Miłecki
bd150495bb brcm47xx: refresh kernel config
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45921
2015-06-07 10:09:10 +00:00
Felix Fietkau
b9ebf29fbd kernel: move a symbol from the ipq806x config to generic to prevent it from being nuked by make kernel_oldconfig
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45920
2015-06-07 07:32:35 +00:00
Felix Fietkau
7138c77f5a kernel: remove NAND flash related kmod-* packages
They are useless, as the platform already selects the right options for
NAND support. The main reason for removing them is the fact that it
makes kernel configs more annoying to maintain on platforms that provide
NAND drivers but disable them (e.g. ramips)

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45919
2015-06-07 07:22:11 +00:00
John Crispin
bd87d11e58 ralink: add missing symbol
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45918
2015-06-07 07:12:23 +00:00
Rafał Miłecki
2364dd9331 bcm53xx: refresh kernel config
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45916
2015-06-06 22:34:37 +00:00
Rafał Miłecki
46a25c6e8a bcm53xx: fallback to default_do_upgrade if NAND upgrade fails
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45915
2015-06-06 17:52:53 +00:00
Rafał Miłecki
3d4f163df1 bcm53xx: sysupgrade: drop useless shift in platform.sh
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45914
2015-06-06 17:26:05 +00:00
Rafał Miłecki
46bc3ed25a brcm47xx: sysupgrade: drop useless shift in platform.sh
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45913
2015-06-06 17:25:57 +00:00
Rafał Miłecki
54fb91f0cf bcm53xx: extract TRX from image on the fly
Extracting TRX to separated file in /tmp/ just wastes some RAM while we
can just pass a proper extracting command to the default_do_upgrade.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45912
2015-06-06 17:23:03 +00:00
Rafał Miłecki
5e90144aec bcm53xx: sysupgrade: extract TRX partitions directly from vendor image
Extracting full TRX out of vendor format is not needed as otrx supports
passing TRX offset. This saves some RAM during sysupgrade.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45911
2015-06-06 17:05:31 +00:00
Rafał Miłecki
48da51ed03 bcm53xx: update NVRAM driver to support getting contents
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45907
2015-06-05 21:49:57 +00:00
Rafał Miłecki
fc0776f2c7 brcm47xx: backport MIPS BCM47XX changes queued for 4.2
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45906
2015-06-05 20:41:18 +00:00
John Crispin
7d8de52d4d ar71xx: fix AR71XX_MODEL for TP-Link TL-WA830RE v1
The v1 identifies as v10 internally. As there is no TL-WA830RE v10, add a
workaround to avoid confusing users.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45903
2015-06-05 14:12:34 +00:00
John Crispin
0ec720e9a9 ramips: Add support for RT5350F-OLinuXino V2
Version 2 : White spaces and  alphabetical order problems
 fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
 https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware

Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>

SVN-Revision: 45902
2015-06-05 14:12:25 +00:00
John Crispin
0da6f8a52b brcm47xx: extract TRX from image on the fly
Extracting TRX to separated file in /tmp/ requires extra RAM which may
not be available on some chepaer devices. Instead of that lets pass a
proper extracting command to the default_do_upgrade.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45901
2015-06-05 14:12:15 +00:00
John Crispin
262f6869a2 lantiq: Backport gpio-stp-xway to fix the highest bits of the PHY LEDs
This fixes the LAN2 LED on Arcadyan VGV7510KW22.

SVN-Revision: 45899
2015-06-05 14:11:51 +00:00
John Crispin
ca1db6b5ce lantiq: Add support for Arcadyan VGV7510KW22 (known as o2 Box 6431)
SVN-Revision: 45897
2015-06-05 14:11:36 +00:00
Felix Fietkau
4480fbce62 ramips: improve tx clean up and add fe_tx_ring struct
if there is any new tx need to clean up. do it in next napi poll.
collect tx related members to fe_tx_ring struct. for better
cache usage and more readable.

Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 45895
2015-06-05 08:59:57 +00:00
Felix Fietkau
2a66c9886f ramips: change ethernet napi interrupt sequence
when open device. first ready napi software rx.
then enable hardware interrupt.
final start software tx queue to send data.

Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 45894
2015-06-05 08:59:48 +00:00
Felix Fietkau
0d043d3ac0 ramips: fix ethernet vlan tx offload support check when delete
Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 45893
2015-06-05 08:59:42 +00:00
Felix Fietkau
4746e539e0 ramips: fix the memory map on FireWRT
Avoid the use of memory marked as reserved

MT7621 support 512MB memory.
According to "MT7621_ProgrammingGuide_Preliminary_Platform.pdf"
0x0~0x1c000000        448MB
0x20000000~0x4000000  64MB
total 512MB

Signed-off-by: wengbj <fl.service@t-firefly.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45892
2015-06-05 08:07:41 +00:00
Felix Fietkau
5a64d5337b kernel: adjust mips highmem offset to avoid the need for -mlong-calls on systems with >256M RAM
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45891
2015-06-05 08:07:35 +00:00
Felix Fietkau
69d79ea951 ramips: use highmem on the FireWRT board
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45890
2015-06-04 21:45:24 +00:00
Felix Fietkau
d7023e105f ramips: enable highmem support for mt7621
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45889
2015-06-04 21:45:12 +00:00
Felix Fietkau
7a23eae245 ramips: remove prompt of the USB_MT7621_XHCI_PLATFORM symbol to avoid issues with kernel_menuconfig
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45888
2015-06-04 21:45:01 +00:00
John Crispin
2575637497 lantiq: Make the CRC32 poly value configurable per device
This also adds the old hardcoded value to the VGV7519BRN profile to make
sure that images are still generated correctly.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45882
2015-06-03 13:58:57 +00:00
John Crispin
f9f093baa3 ipq806x: missing symbol
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45880
2015-06-03 13:58:30 +00:00
Jonas Gorski
6d07290de3 brcm63xx: fix livebox image generation
Livebox does need the uncompressed kernel, so just create it during
image generation.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45875
2015-06-02 10:23:45 +00:00
John Crispin
ff324050c3 ipq806x: move stmmac support in the kernel binary
Ethernet GMAC is built-in the SoC, so there is no need to enable it as a
module. We'll just assume we need it. That's what is done for other
platform where this driver is used so it'll make things more consistent.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45871
2015-06-01 20:11:35 +00:00
Jonas Gorski
9c6945d7a1 brcm63xx: delete uncompressed kernels after use
Delete the dtb appended, uncompressed kernels after having compressed
them, so they don't end in the image builder.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45869
2015-06-01 12:37:34 +00:00
Jonas Gorski
43c0a725af lantiq: fix VG3503J rootfs offset
In r44391 the kernel partion size was increased to allow larger kernels,
but the rootfs partition offset was missed. Fix this by setting the
rootfs offset to the expected value.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45868
2015-06-01 12:37:24 +00:00
Jo-Philipp Wich
11f05afd26 imagebuilder: create cache directory if needed (#18629)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45866
2015-06-01 06:15:39 +00:00
Rafał Miłecki
6bc9e00e94 kernel: backport ssb fix for WRT350N v1 (BCM4705) reboots
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45865
2015-06-01 06:11:26 +00:00
John Crispin
c0c8d3a95f au1000: add a missing dependency to the pcmcia module
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45864
2015-06-01 06:03:52 +00:00
John Crispin
6938dac23b malta: add default network configuration
I didn't figure out how to achieve this using uci-defaults-new.sh,
so use old-school uci-defaults script as that's what is used on
realview as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 45857
2015-05-31 17:45:43 +00:00
Felix Fietkau
677741ef95 ar71xx: use Image/BuildLoaderPatched for TPLINK-SAFELOADER images
Building the loader in Image/Build/TPLINK-SAFELOADER would break the image
builder as no target compiler is available in that stage.

Fixes #19580

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45855
2015-05-30 22:55:50 +00:00
Felix Fietkau
64b789db56 ar71xx: add Image/BuildLoaderPatched macro
In contrast to Image/BuildLoader, Image/BuildLoaderPatched first patches the
kernel command line in the image and then builds the loader without command
line. This allows building loaders for systems which don't boot correctly when
the kernel command line is provided by the loader (like the TP-LINK CPE series).

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45854
2015-05-30 22:55:40 +00:00
John Crispin
b34988d5d0 lantiq: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45851
2015-05-30 20:28:57 +00:00
John Crispin
50da78705a kernel: upstream fix: mount overlayfs r/o if workdir cannot be created
move the patch to the proper folder

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45848
2015-05-30 13:16:23 +00:00
Felix Fietkau
e56b6f6e66 ramips: fix swapped colors for router LED on WHR-1166D (thx, Björn)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45847
2015-05-30 09:39:37 +00:00
Felix Fietkau
1e659c29ec ramips: rename status led to wifi on WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45846
2015-05-30 09:01:41 +00:00
Felix Fietkau
a6df9f0472 ramips: fix buttons on WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45845
2015-05-29 22:42:32 +00:00
Felix Fietkau
5d6788f773 ramips: extract MAC address on WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45844
2015-05-29 21:42:06 +00:00
Felix Fietkau
420cdb3783 ramips: fix partition layout of WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45843
2015-05-29 21:25:23 +00:00
Felix Fietkau
8b42d93358 ramips: implement sysupgrade support for whr-300hp2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45842
2015-05-29 21:13:28 +00:00
Jonas Gorski
aafc3092e2 ixp4xx: use usb-*-pci where appropriate
Most boards use pci connected usb controllers, so make sure to include
the pci drivers.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45840
2015-05-29 14:39:12 +00:00
Jo-Philipp Wich
dcd7479a99 sunxi: correct default package selection, fixes imagebuilder
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45839
2015-05-29 13:55:26 +00:00
Felix Fietkau
1520df3387 ar71xx: use Image/BuildKernel/Initramfs template to fix image builder errors
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45838
2015-05-29 13:41:41 +00:00
John Crispin
afbf104a4e generic: mount overlayfs r/o if workdir cannot be created
This is the case e.g. if JFFS2 partition is full.

see: https://www.mail-archive.com/linux-unionfs@vger.kernel.org/msg00246.html
(a small error in a logmessage was changed and reported upstream)

runtime tested on ar71xx with kernel 3.18.11 and r45772
this paritially fixes #19564

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
Acked-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45833
2015-05-29 12:36:42 +00:00
John Crispin
d2a2eb7e48 ipq806x: replace caf nss-gmac driver by upstream stmmac
This driver has been cherry-picked and backported from the following
LKML thread:
*https://lkml.org/lkml/2015/5/26/744

It also updates the DT accordingly.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45831
2015-05-29 12:26:01 +00:00
John Crispin
72369c2976 ipq806x: enable kernel support for Fixed PHY emulation
Most ipq806x platforms use an ethernet switch, and the new upstream
GMAC driver makes use of the Fixed PHY emulation to force the link
settings despite the lack of PHY.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45830
2015-05-29 12:25:44 +00:00
John Crispin
fe844bf0b4 kernel: add missing STMMAC options in generic configs
STMMAC_PLATFORM and STMMAC_PCI have been added recently in the kernel,
but show up only when STMMAC driver is enabled. So se'll add it in the
generic config, so the kernel build doesn't stall whenever we enable
this driver.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45828
2015-05-29 12:25:29 +00:00
John Crispin
30bbe0b388 ipq806x: move arm-gic include into pcie patch
This include is necessary starting at the PCIe patch, which has a lower
number. So in order to keep the patches consistent, we'll move the
arm-gic include in the first patch who needs it.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45827
2015-05-29 12:25:15 +00:00
John Crispin
590be1fd87 ixp4xx: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45826
2015-05-29 12:20:39 +00:00
John Crispin
a5a935b49a brcm2708: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45824
2015-05-29 11:28:54 +00:00
John Crispin
12772b66fe ipq806x: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45823
2015-05-29 11:28:44 +00:00
John Crispin
1985e88b35 gemini: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45822
2015-05-29 11:28:33 +00:00
John Crispin
9927a9a5f8 octeon: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45821
2015-05-29 11:28:20 +00:00
John Crispin
adbec3f132 ramips: fix imagebuilder
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45820
2015-05-29 11:28:10 +00:00
Jo-Philipp Wich
80a933af98 au1000/au1550: fix profile package list
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45819
2015-05-29 11:04:04 +00:00
Jo-Philipp Wich
f449ba5c94 au1000/au1550: enable pcmcia support flag
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45818
2015-05-29 11:03:59 +00:00
Jo-Philipp Wich
f19757215b au1000: fix kmod-pcmcia-au1000
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45817
2015-05-29 11:03:55 +00:00
Jo-Philipp Wich
82aa281d61 mxs: fix imagebuilder
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45815
2015-05-29 08:42:50 +00:00
Jo-Philipp Wich
ae1f0d3eb4 x86/64: add e1000e to the default packages
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45814
2015-05-29 08:20:58 +00:00
Rafał Miłecki
92ebd6fdbe brcm47xx: image: fix typo in Asus WL-500gP v2 fw file name
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45811
2015-05-28 19:53:59 +00:00
Jo-Philipp Wich
7d44f7630f au1000: use srecimage.pl instead of objcopy, fixes imagebuilder
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45809
2015-05-28 15:54:01 +00:00
Jo-Philipp Wich
cb7dc3b691 ar7: fix imagebuilder
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45807
2015-05-28 13:45:33 +00:00
Jo-Philipp Wich
ba9f34a389 at91: fix imagebuilder
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45806
2015-05-28 13:25:21 +00:00
Jo-Philipp Wich
d7f6b8e3be xburst: fix imagebuilder
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45805
2015-05-28 12:25:45 +00:00
Jo-Philipp Wich
282894a407 malta: fix imagebuilder
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45804
2015-05-28 12:05:57 +00:00
Jo-Philipp Wich
e91342e285 IB: make CONFIG_IB_STANDALONE the default
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45800
2015-05-28 09:51:38 +00:00
Jo-Philipp Wich
3c5357d6ef feeds: use common macro "FeedSourcesAppend" to populate opkg configurations
This introduces a common macro to assemble the correct url templates to
avoid code duplication and have the feed config handling in a central place.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45799
2015-05-28 09:47:37 +00:00
Felix Fietkau
21e16964bf adm5120: fix subtarget dependency for kmod-pata-rb153-cf
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45798
2015-05-28 09:06:28 +00:00
Rafał Miłecki
ebd651ad99 brcm47xx: add LEDs/buttos for Asus N10U
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45797
2015-05-28 08:08:17 +00:00
Rafał Miłecki
a5000c0af6 brcm47xx: drop 4.0 patch that is in 4.0.4
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45796
2015-05-28 08:08:11 +00:00
John Crispin
3f9999b44b ramips: dont set illacc to y by default
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45795
2015-05-27 20:06:06 +00:00
John Crispin
71621ca702 ipq806x: add missing symbol
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45794
2015-05-27 20:05:03 +00:00
John Crispin
302a9f8982 ramips: diable ill_acc driver by default
this treacled down via the stable tree and wandered into 3.18.14

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 45793
2015-05-27 20:02:04 +00:00
Imre Kaloz
9fb062cf93 mvebu: make flashing more safe
Turn on the auto recovery feature when flashing
and turn it off on successful bootup.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45792
2015-05-27 19:03:22 +00:00
Rafał Miłecki
9845d729a9 bcm53xx: build images for Asus devices
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45790
2015-05-27 16:20:06 +00:00
Rafał Miłecki
69aefc771f brcm47xx: build images for Asus devices
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45789
2015-05-27 15:37:05 +00:00
Jo-Philipp Wich
43b5730c98 sunxi: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45788
2015-05-27 15:34:48 +00:00
Jo-Philipp Wich
0cce8316d9 realview: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45787
2015-05-27 15:34:38 +00:00
Jo-Philipp Wich
f2a75b6ca4 omap: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45786
2015-05-27 15:34:30 +00:00
Jo-Philipp Wich
5258a2beec ixp4xx: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45785
2015-05-27 15:34:19 +00:00
Felix Fietkau
388404764d kernel: bridge: backport two snooping related patches
With this patch the following two patches are backported:

* bridge: fix parsing of MLDv2 reports
* bridge: allow setting hash_max + multicast_router if interface is down

The former one is an important fix which got just applied to the net-tree
and is queued for stable. The latter is a patch which is needed to make
the hash_max and multicast_router attributes configurable through
netifd.

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>

SVN-Revision: 45783
2015-05-27 15:20:04 +00:00
Jo-Philipp Wich
e814e946a6 gemini: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45782
2015-05-27 15:18:36 +00:00
Jo-Philipp Wich
8f032fdda1 cns3xxx: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45781
2015-05-27 15:18:29 +00:00
Jo-Philipp Wich
957534693c brcm63xx: use common image prefix
Also remove "redbootscript" and "redbootscript.padded" junk files.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
Acked-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45780
2015-05-27 15:18:21 +00:00
Jo-Philipp Wich
048f46a075 brcm47xx: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45779
2015-05-27 15:04:02 +00:00
Jo-Philipp Wich
c5e59e4785 arm64: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45778
2015-05-27 14:57:38 +00:00
Felix Fietkau
83703fc076 ramips: check size after padding
Signed-off-by: Cristian Morales Vega <cristian@samknows.com>

SVN-Revision: 45777
2015-05-27 14:56:22 +00:00
Felix Fietkau
564fdae968 kirkwood: disable TSO on the ethernet device by default, fixes data corruption issues (#19735)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45776
2015-05-27 14:56:13 +00:00
Jo-Philipp Wich
52ec6374d4 ar7: use common image prefix
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45775
2015-05-27 14:53:25 +00:00
Rafał Miłecki
f08a10f2b9 brcm47xx: build image for Asus RT-N66U
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45774
2015-05-27 13:54:19 +00:00
Jo-Philipp Wich
6c21bcaa65 IB: use online repositories
Change the IB packaging to only embed libc, kernel and kmod packages by default
and generate repositories.conf to refer to the remote package repositories.

Introduce a new config option CONFIG_IB_STANDALONE which restores the old
behaviour of building self contained IB archives.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 45772
2015-05-27 11:22:20 +00:00
Imre Kaloz
f1ebb1dddd mvebu: update Linux 4.0 patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45762
2015-05-26 09:31:39 +00:00
Imre Kaloz
588acc2cba generic/4.0: update to 4.0.4
Update kernel sources and refresh some patches.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45761
2015-05-26 09:31:16 +00:00
Felix Fietkau
7c5c213621 ar71xx: fix tl-wr710n images (#19692)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45756
2015-05-26 07:13:40 +00:00
Felix Fietkau
9f0ffef86a kirkwood: disable the bogus CONFIG_IP_ADVANCED_ROUTER override (#19722)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45753
2015-05-25 22:59:15 +00:00
Felix Fietkau
7b85e8e316 mpc85xx: TL-WDR4900: Fix port 6 being shown as up (10MBit/half) in LUCI/swconfig
Currently port 6 is shown as up 10MBit/half in LUCI and swconfig.
Reason is that all bits in the port 6 config are zero.
This means that also the aneg flag is not set and in this case
ar8216_read_port_link hardcodes the link to be up.

This is no real problem but a little annoying.
To fix this initialize port 6 with the aneg bit enabled.
This causes ar8216_read_port_link to evaluate the link status bit which is
always zero for port 6 as no PHY is connected to this port.
And it doesn't hurt as port 6 isn't connected to anything on TL-WDR4900.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 45749
2015-05-25 21:15:37 +00:00
Jonas Gorski
caea19a3e0 ramips: fix hang on boot on rt305x
Fix an upstream regression on 3.18+ that causes rt305x based devices
to hang on boot.

Fixes #19715.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45747
2015-05-25 18:02:32 +00:00
John Crispin
ab84e2d704 octeon: build squashfs image for UBNT ERLITE
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 45732
2015-05-23 15:28:20 +00:00
John Crispin
b4494d9713 ipq806x: enable cpu idle support in kernel conf
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45731
2015-05-23 15:28:11 +00:00
John Crispin
8e49b4b902 ipq806x: add & enable cpufreq support
This change set enables frequency scaling on ipq806x, which speeds-up
the CPU and allows it to achieve its max frequency.

These patches are cherry-picked & backported from the following location:
*130-132: linux-next
*133-143: LKML - https://lkml.org/lkml/2015/3/21/15
*144: derived from other qcom similar dts
*145: derived from https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-3.14/drivers/cpufreq/cpufreq-krait.c

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45730
2015-05-23 15:28:02 +00:00
John Crispin
0b24527e4d ipq806x: add power regulators support
Patches are cherry-picked from linux-next. We're also adding the
corresponding config option to the kernel.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45729
2015-05-23 15:27:54 +00:00
John Crispin
f74477de48 ipq806x: disable i2c device on gsbi4
Patch cherry-picked from the following location:
https://chromium-review.googlesource.com/#/c/269931/

Disable the i2c device on gsbi4 and mark gsbi4_h and gsbi4_qup clks as
unused. If they are enabled, clock framework will turn them off at end
of probe. On ipq806x by design gsbi4_qup, gsbi4_h clks and i2c on gsbi4
are meant for RPM usage. So turning them off in kernel is incorrect.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45728
2015-05-23 15:27:45 +00:00
John Crispin
1c6d332d8f ipq806x: refresh kernel patches
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45727
2015-05-23 15:27:28 +00:00
John Crispin
66950455b7 ar71xx: Add support for the Meraki MR12 & MR16
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.

Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>

SVN-Revision: 45726
2015-05-23 15:27:22 +00:00
John Crispin
870cd41936 rampis: add support for status led on ASUS RT-N14U
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)

Signed-off-by: Matteo Panella <m.panella@level28.org>

SVN-Revision: 45725
2015-05-23 15:27:10 +00:00
John Crispin
9c86abae0e ramips: Adding support for AXIMCom MR-102N 3G/4G Travel Mobile Router
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port.  The original product information can be found at:
http://www.aximcom.com/en/MR-102N

Signed-off-by:	Tai-hwa Liang <atliang@gmail.com>

SVN-Revision: 45724
2015-05-23 15:27:05 +00:00
John Crispin
4810f3f803 ramips: fix switch names for several boards in device tree
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 45723
2015-05-23 15:26:51 +00:00
John Crispin
5e96c2d541 ramips: add support for Comfast CF-WR800N
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45722
2015-05-23 15:26:39 +00:00
John Crispin
230efe318f lantiq: Fix initialization of the PCI IRQs when PCIe is also enabled
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45718
2015-05-23 15:25:59 +00:00
John Crispin
390924e662 lantiq: Fix PCIe bus when PCI is also enabled.
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

SVN-Revision: 45717
2015-05-23 15:25:51 +00:00
Hauke Mehrtens
47eca7a1ca bcm53xx: add OHCI (USB 1.1) support
There is also a OHCI controller, activate it for USB 1.1 support.

This should close #19601.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

SVN-Revision: 45716
2015-05-23 14:54:44 +00:00
Jonas Gorski
dc60b7fffa arm64: enable new errata backported to 3.18
3.18.13 introduced a bunch of new errata, enable them to be on the
safe side.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45715
2015-05-22 22:51:37 +00:00
Jonas Gorski
4e2b4d8072 kernel: add missing generic config symbol
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45714
2015-05-22 22:51:34 +00:00
Jonas Gorski
76d079204d kernel: update 3.18 to 3.18.14
Changelogs:

* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.12
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.13
* https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.14

Build tested on brcm63xx and ipq806x, runtested on brcm63xx.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45711
2015-05-21 19:32:46 +00:00
Jonas Gorski
4bb7b2186e brcm63xx: fix failsafe lan and status led for DSL-274xB rev. F1
Add it to the appropriate places so the power led properly works
and ethernet is properly configured for failsafe.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45709
2015-05-21 19:32:00 +00:00
Jonas Gorski
509c3211d6 brcm63xx: Add Huawei HG655b support
This patch adds support for the Huawei HG655b.

Nothing much special in this router, it's just another BCM6368 with
a Ralink RT3062 wifi chip and the calibration data embedded in the
main flash chip at offset 0x7c0000. There is also configuration data
used by the OEM firmware before the cal_data partition, this area is
protected by the board_data partition in this patch.

Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45708
2015-05-21 19:31:54 +00:00
Steven Barth
53098a8aa5 generic/4.0: fix error during kernel patch application
Commit 5168c9a5702648eb690d32ec821647aca80aeba9 introduced a regression
during patch application on the 4.0 kernel. Some of the patched content
doesn't match the actual code, therefore leading to the following error:
  Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch
  patching file net/ipv6/ip6_output.c
  Hunk #1 FAILED at 886.
  1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c
  patching file net/ipv6/route.c
  Hunk #1 succeeded at 2247 (offset 2 lines).
  Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f)

This change just adapts the actual patch to fix what is in kernel 4.0
and make it apply cleanly.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45705
2015-05-20 19:23:33 +00:00
Imre Kaloz
c4c4cce190 mvebu: supress useless in-cpu rtc init on the Mamba
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45704
2015-05-19 22:54:05 +00:00
Steven Barth
1296956908 linux: backport IPv6 SAS fixes for source-specific routes
Signed-off-by: Steven Barth <steven@midlink.org>

SVN-Revision: 45699
2015-05-19 07:43:59 +00:00
Rafał Miłecki
63bb7c51db bcm53xx: add Asus RT-AC87U partitioning hacky workaround
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45694
2015-05-17 12:10:38 +00:00
Rafał Miłecki
75b8e247e3 bcm53xx: try to fix network on Asus RT-AC87U
This device seems to have switch port 7 connected to the CPU:
vlan1ports=1 2 3 5 7*
vlan2ports=0 7u
it should be handled by eth1 and NVRAM seems to confirm that (no
et0macaddr entry, existing et1macaddr & et1phyaddr entries).

One of the remaining ports (4/8?) may be connected to the Quantenna SoC.
Original firmware boot log contains following messages:
(0x00,0x5d)Port 5 States Override: 0xfb
(0x00,0x5f)Port 7 States Override: 0xfb
(0x00,0x0e)Port 8 States Override: 0x0a
(why does it force port 5 state?!)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45692
2015-05-16 17:14:25 +00:00
Rafał Miłecki
ab83610563 bcm53xx: use backported Asus RT-AC87U DT patch
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45691
2015-05-16 15:44:00 +00:00
Rafał Miłecki
abed46aacc bcm53xx: enable RT-AC87U UART console
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 45690
2015-05-16 11:45:52 +00:00
Rafał Miłecki
3dd9274332 bcm53xx: add support for SmartRG SR400ac
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45686
2015-05-13 20:01:15 +00:00
Rafał Miłecki
b4ecf19faa bcm53xx: replace DT patches with backports from stblinux
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45685
2015-05-13 20:01:03 +00:00
Rafał Miłecki
af019cad56 bcm53xx: use of_machine_is_compatible helper in b53 fix
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45684
2015-05-13 14:34:23 +00:00
Rafał Miłecki
afb98aea4d bcm53xx: fix "typo" in b53 patch fixing R8000 CPU port
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45683
2015-05-13 13:12:57 +00:00
Rafał Miłecki
610ee0d85a bcm53xx: add b53 hacky workaround for Netgear R8000 CPU port
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45682
2015-05-13 13:11:17 +00:00
Rafał Miłecki
2d3aaa2d2f bcm53xx: fix default network interface on Netgear R8000
It has 3 Ethernet interfaces, each of them connected to separated switch
port. Default NVRAM uses switch port 8 as CPU which is connected to the
3rd interface (eth2).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45681
2015-05-13 13:11:04 +00:00
Rafał Miłecki
45ec92fa30 bcm53xx: bgmac: add support for the 3rd core
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45680
2015-05-13 13:11:00 +00:00
Rafał Miłecki
d2e5e2bf54 bcm53xx: sync NVRAM and SPROM drivers with upstream version
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45678
2015-05-13 08:30:45 +00:00
Rafał Miłecki
260383aeb1 kernel: backport struct ssb_sprom changes submitted by MIPS tree
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45677
2015-05-13 07:52:43 +00:00
Rafał Miłecki
e93c68eedd b53: Allow using all ports on BCM53012
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports
5, 7 and 8 connected to Ethernet interfaces:
vlan1ports=0 1 2 3 5 7 8*
vlan2ports=4 8u
Port 6 seems to be always disabled.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45676
2015-05-12 13:18:53 +00:00
Felix Fietkau
6ceb1b0358 ar71xx: convert tl-wr741nd v1/v2 to new image building code, add infrastructure for building the loader
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45672
2015-05-11 09:08:33 +00:00
Felix Fietkau
ac0e2479dc mtd: remove the warning about read-only caused by size vs. block boundary mismatch
Since the kernel/rootfs split handling was modified 2 years ago by r37283 (
https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins,
users have seen rather scary mtd errors in the log at every boot. The message
ends "-- forcing read-only", which looks a bit error-like. That error has
been mentioned in some forum threads, when users have noticed this message
instead of some actual error.

[    2.940000] 0x000000070000-0x000000ff0000 : "firmware"
[    2.970000] 2 netgear-fw partitions found on MTD device firmware
[    2.970000] 0x000000070000-0x000000188440 : "kernel"
[    2.980000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[    2.990000] 0x000000188440-0x000000ff0000 : "rootfs"

The patch removes the rather useless warning message.

signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

SVN-Revision: 45669
2015-05-10 16:09:58 +00:00
Felix Fietkau
b33752051f ar71xx: add platform_pre_upgrade for sysupgrade
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45667
2015-05-10 13:54:25 +00:00
Felix Fietkau
9ebb99cb98 kernel: fix regression in backtrace module info change (#19631)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45665
2015-05-10 13:16:40 +00:00
Felix Fietkau
cfb56b4811 ipq806x: add pcie support to ipq806x based platforms
This change adds PCIe support to IPQ806x based platforms. The driver is
actually cherry-picked from the following LKML thread:
*https://lwn.net/Articles/643086/ (patches 110-111)

We also add here an additional fix to support multiple PCI controllers
on the same platform (patch 112), and to patch the ap148 & dbs149 DTS
files (patch 113).

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45663
2015-05-10 11:47:09 +00:00
Felix Fietkau
3c4bc0cd77 ipq806x: add support for zImage kernel
This change enable zImage+appended dtb support in ipq806x kernel
options. The zImage will now be generated as part of the kernel
binaries. Platforms which do not have DT support enabled in U-boot
can now make use of it by generating zImage files and appending dtb
to it.

It is not used yet but it is done as a stepping stone for early IPQ806x
platforms, which did not include DT support in U-boot.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45662
2015-05-10 11:47:02 +00:00
Felix Fietkau
bdcba36442 ipq806x: fix boot freeze on zImage kernel
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended
on most ARM architectures. This automatically calculate ZRELADDR by
masking PHYS_OFFSET with 0xf8000000.

On IPQ806x though, the first ~20MB of RAM is reserved for the hardware.
In newer bootloader, when DT is used, this is not a problem, we just
reserve this memory in the device tree. But if the bootloader doesn't
have DT support, then ATAGS have to be used. In this case, the ARM
decompressor will position the kernel in this low mem, which will not be
in the RAM section mapped by the bootloader, which means the kernel will
freeze in the middle of the boot process trying to map the memory.

As a work around, this patch allows disabling AUTO_ZRELADDR when
ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders
which don't support device-tree, which is the case on certain early
IPQ806x based designs.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45661
2015-05-10 11:46:56 +00:00
Felix Fietkau
9913b6a90a generic: add CRYPTO_DEV_QCE option to default config
This option has been added in kernel 3.17. It shows-up only when both
ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default
to avoid stalling the build when these conditions are met.

Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>

SVN-Revision: 45658
2015-05-10 11:46:41 +00:00
Luka Perkov
2a9ebfb503 ar71xx: add status led found on ew-dorin boards
Signed-off-by: Catrinel Catrinescu <cc@80211.de>

SVN-Revision: 45656
2015-05-10 07:47:04 +00:00
Felix Fietkau
53827cdc82 kernel: when KALLSYMS is disabled, print module address + size for matching backtrace entries
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45655
2015-05-10 00:02:18 +00:00
Felix Fietkau
a13783f8c3 kernel: fix pppoe disconnect issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45653
2015-05-09 21:14:41 +00:00
Rafał Miłecki
3a6cdac37c kernel: backport first bcma patches from 4.2
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45652
2015-05-09 17:38:48 +00:00
Felix Fietkau
dbb99e937a kernel: add accidentally left out fib trie backport patch
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45650
2015-05-08 21:46:51 +00:00
Luka Perkov
3209b13b3f generic: refresh patches
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45648
2015-05-08 20:12:42 +00:00
Luka Perkov
7437be53ba kirkwood: add support for the Seagate GoflexHome
Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 45647
2015-05-08 20:12:39 +00:00
Felix Fietkau
7b01a650f8 ar71xx: allow mktplinkfw calls from the new image code to fail (because of oversized images)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45646
2015-05-08 14:02:50 +00:00
Felix Fietkau
293b82501c ar71xx: allow tp-link initramfs images to exceed size limits
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45645
2015-05-08 14:02:43 +00:00
Felix Fietkau
5b14d96ded ar71xx/image: move TPLINK-LZMA image to new build code
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties.
v2: set correct DEVICE_PROFILES for all images.
v2: migrate TP-LINK TL-WR710N v2 which was committed after v1.
v2: split very very long line `TARGET_DEVICES +=` into smaller parts

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 45643
2015-05-08 14:02:23 +00:00
Felix Fietkau
11c588bc96 ar71xx: do general formatting on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45640
2015-05-08 12:24:30 +00:00
Felix Fietkau
d4600d867c ar71xx: fix spelling, add copyright on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45639
2015-05-08 12:24:23 +00:00
Felix Fietkau
b1aea59f08 ar71xx: add support for Green WAN LED on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45638
2015-05-08 12:24:17 +00:00
Felix Fietkau
aa970f13a3 ar71xx: add support for green LAN LEDS for wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45637
2015-05-08 12:24:11 +00:00
Felix Fietkau
17c78d12bd ar71xx: fix amber WAN LED setting for wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45636
2015-05-08 12:24:03 +00:00
Felix Fietkau
5e1e04e505 ar71xx: make WLAN button RFKILL on wnr2000-v4
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45635
2015-05-08 12:23:58 +00:00
Felix Fietkau
b1380ebae3 ar71xx: set all buttons to be active_low on wnr2000-v4
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45634
2015-05-08 12:23:53 +00:00
Felix Fietkau
6413f40e96 ar71xx: fix ethernet on wnr2000-v4
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861

I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
  1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
  2) must init GMAC0 before GMAC1

That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.

An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.

2) Possible consequence of no longer explicitly setting ethernet duplex/speed.

Review: With this patch, my ethernet and wireless works.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45633
2015-05-08 12:23:45 +00:00
Felix Fietkau
5c5648f4b7 ar71xx: track the correct WAN interface on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45632
2015-05-08 12:23:40 +00:00
Felix Fietkau
6b6cc03cff ar71xx: fix LAN portmasks on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45631
2015-05-08 12:23:35 +00:00
Felix Fietkau
a51f5cace4 ar71xx: use a common naming scheme for LEDS on wnr2000-v4
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45630
2015-05-08 12:23:27 +00:00
Imre Kaloz
9d3f24465f mvebu: add xhci phy support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45629
2015-05-08 12:12:20 +00:00
Luka Perkov
4a3850b397 ar71xx: make art partition read only on 16MB ew-dorin board
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45627
2015-05-08 10:45:26 +00:00
Felix Fietkau
4babe9dc6d ar71xx: fix 82_patch_ath10k
It has been broken since the new ath10k firmware introduced in r44656.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>

SVN-Revision: 45624
2015-05-08 10:43:55 +00:00
Felix Fietkau
333579e527 kernel: backport upstream usbnet fix (fixes #19455)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45621
2015-05-06 10:19:22 +00:00
Rafał Miłecki
501da07c5d brcm47xx: fix regression in NVRAM support for WGT634U
We were calculating wrong offset, NVRAM wasn't found and OpenWrt didn't
boot.

Fixes: 9019803 ("brcm47xx: backport BCM47XX arch patches (clean NVRAM code, later init)")
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45618
2015-05-06 05:54:19 +00:00
Imre Kaloz
aea93173d1 generic/4.0: update to 4.0.1
Also refresh one patch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 45601
2015-05-03 18:04:46 +00:00
Imre Kaloz
3ee45e61fe mpc85xx: replace WDR4900 uci-defaults ethernet MAC address hack with DTS entry
This also changes the MAC address to one of the adresses actually used by the
stock firmware on one of the ethernet interfaces.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45599
2015-05-03 18:00:47 +00:00
Imre Kaloz
322d798510 mpc85xx: gianfar: add mtd-mac-address support
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45598
2015-05-03 17:59:46 +00:00
Imre Kaloz
b9fbf31fe7 mpc85xx: move newly created files from patch files to files directory
This will make these files much more maintainable.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45597
2015-05-03 17:58:45 +00:00
Imre Kaloz
f86c07d8d4 The ability to read MAC addresses from MTD is useful for other targets besides ramips and lantiq as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 45596
2015-05-03 17:56:32 +00:00
Luka Perkov
8084b056e2 ar71xx: fix leds and gpio on wpj344
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45589
2015-04-29 20:04:46 +00:00
Luka Perkov
cd419afd2c ar71xx: fix sysupgrade for compex-wpj344
Moved board to the right magic case.

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 45588
2015-04-29 13:52:34 +00:00
Jonas Gorski
954004eccc kernel: disable INET_LRO by default
INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.

So just disable it for everyone.

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45584
2015-04-28 13:31:08 +00:00
Jonas Gorski
9feb1361c4 brcm63xx: fix bcm6348 ext irqc compatible name
This was a remnant of an old version.

Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45583
2015-04-27 11:06:05 +00:00
Jonas Gorski
5e7f4ab632 brcm63xx: fix bcm3368.dtsi typo.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>

SVN-Revision: 45582
2015-04-27 11:06:00 +00:00
Felix Fietkau
d2e02d6377 sdk: filter out CONFIG_SIGNED_PACKAGES for generated config
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45581
2015-04-25 12:39:02 +00:00
Felix Fietkau
51d0476ab0 kernel: implement RENAME_EXCHANGE support for jffs2 - overlayfs requires it
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45580
2015-04-25 10:47:18 +00:00
Rafał Miłecki
33e597b241 bcm53xx: sort ports from NVRAM entries before matching them
Some devices have unsorted ports which may lead to broken config.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45575
2015-04-24 07:47:25 +00:00
Florian Fainelli
00fb1bc098 netlogic: copy initramfs image to $(BIN_DIR)
Signed-off-by: Florian Fainelli <florian@openwrt.org>

SVN-Revision: 45574
2015-04-23 22:31:36 +00:00
Rafał Miłecki
e175b199f8 kernel: backport rest of bgmac patches to 4.0
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45573
2015-04-23 19:11:11 +00:00
Rafał Miłecki
6bfb1a4b11 kernel: backport few bgmac patches to 4.0
I still need to test following patch before backporting:
bgmac: leave interrupts disabled as long as there is work to do

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 45571
2015-04-23 12:30:51 +00:00