All devices are now using the HW SPI driver, so this is not necessary
anymore.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48291
This allows devices to use SPI without having to re-define (and thus
duplicating) the whole SPI node.
By default SPI is disabled (as before) because only few devices need it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48286
After the latest pinctrl backports there are only 50 (instead of 56 as
before) GPIOs/pins exported (thus the first GPIO on VRX200 SoCs is now
462, before it was 456). This means that any hardcoded GPIOs have to be
adjusted.
This broke the PCIe driver (which seems to be the only driver which uses
hardcoded GPIO numbers), it only reports:
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
ifx_pcie_wait_phy_link_up timeout
pcie_rc_initialize link up failed!!!!!
To prevent more of these issues in the future we remove the hardcoded
PCIe reset GPIO definition and simply pass it via device-tree (like the
PCI driver does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48285
These were introduced in upstream commit
be14811c03cf "pinctrl/lantiq: introduce new dedicated devicetree
bindings" and finally allow us to use the individual pins within our dts
(for example spi_clk, etc.).
Please note that this changes the number of GPIOs which are available for
some SoCs. VRX200 SoCs for example only have 50 pins, but previously 56
pins were exposed. This means that all places which are using hardcoded
GPIO numbers (which are not passed via device-tree) need to be adjusted
(because the first GPIO number is now 462, instead of 456).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48284
Upstream commit be14811c03cf2 "pinctrl/lantiq: introduce new dedicated
devicetree bindings" allows us to use each pin in the pinmux. This is
useful for example in the "spi" group which contains some pins which
are inputs, and some which are outputs.
These can only be used once the new compatible strings for the pinctrl
node are used.
Additionally 0150-lantiq-pinctrl-xway.patch and the "GPIO PORT3 fix"
(which was part of 0012-pinctrl-lantiq-fix-up-pinmux.patch) were
replaced with their upstream variants which are also in 4.5.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48283
According to the calling convention of the o32 ABI the caller
function must reserve stack space for $a0-$a3 registers in case
the callee needs to save its arguments.
The assembly code of the loader does not reserve stack space for
these registers thus when the 'loader_main' function needs to save
its arguments, those will be stored in the 'workspace' area instead
of the stack.
Because the workspace area is also used by other part of the code, the
saved register values gets overwritten and this often leads to failed
kernel boots.
Fix the code to reserve stack space for the registers to avoid this
error.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 48279
Change MTD on WNDR4300 and WNDR3700v4 to fully utilize the 128MB flash.
Credit to @Tuochenlyu on GitHub.
Signed-off-by: Chris Marchesi <chrism@vancluevertech.com>
SVN-Revision: 48276
PTP requires at least one timer to be 1PPS so describe it.
For testing, load kernel module gianfar_ptp and use ptp4l
from linuxptp.
Copied from FSL P1010RDB reference design.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
SVN-Revision: 48275
The old signature only worked because brnboot ignores the leading "5" in
the signature. We can see the correct signature when flashing a brnImage
via recovery web-interface, in this case brnboot reports:
[CGI-Signature Check] buf:[BRNDA6431], sigInFlash:[BRNDA6431]
Thanks to Mathias Kresin for reporting this.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48269
This add support for IGMP Snooping on atheros switches (disabled by default),
which avoids flooding the network with multicast data.
Tested on TL-WDR4300: disabling IGMP Snooping results in multicast flooding
on each specific port, enabling it back again prevents each port from
receiving all multicast packets.
Partially based on: http://patchwork.ozlabs.org/patch/418122/
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48268
- random-bcm2708 and spi-bcm2708 have been removed.
- sound-soc-bcm2708-i2s has been upstreamed as sound-soc-bcm2835-i2s.
Let's keep linux 4.1 for a while, since linux 4.4 appears to have some issues
with multicast traffic on RPi ethernet:
https://gist.github.com/Noltari/5b1cfdecce5ed4bc08fd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48266
This removes the arch-specific mtdsplit parsers and enables the generic
implementations for brnImage, EVA and TP-Link instead.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48264
On most image types the rootfs ends at an erase-block. However, at least
with brnImages this is not the case: while the partitions are aligned
with the erase-block size there is a 12 byte footer at the end of the
partition which must not be touched by any filesystem. This lead to a
rootfs_data partition which was not aligned properly (and thus ended up
being readonly):
0x000000480000-0x00000085a800 : "rootfs_data" (128 KiB EB)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48263
This allows splitting EVA images (usually found in fritz devices). The
firmware will be split into a kernel and a separate rootfs partition.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48262
This adds brnImage (used with the brnboot bootloader) firmware parsing
support. brnboot verifies the integrity of the firmware stored on the
"Code Image" partitions by looking at the 12 byte footer at the very end
of the partition. This footer contains the checksum of the original
brnImage (kernel + rootfs/squashfs) and must not be touched (by our JFFS2
rootfs_data - otherwise the image will not be bootable anymore).
Big thanks to Mathias Kresin for analyzing the brnImage structure and
finding out the information how to keep images valid even when adding a
nested rootfs_data partition.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48261
Given those patches are relevant to any ARC platform and even
ISA version it makes perfect sense for patches to exist
in one place instead of being duplicated for each new ARC-based ASIC.
Note this is a prerequisite for upstreaming of ARC HS38 support in
OpenWRT.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48241
This switch involved:
[1] Regeneration of config (few options went away)
[2] Regeneration of patches so they apply cleanly (different offsets)
[3] Update of .dts files because we now explicitly specify
memory regions in use as opposed to previously used offset
from 0x8000_0000
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 48240
This patch was merged into upstream Linux 4.1.
This fixes#21587 and was introduced in r48223.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48229
Fully reset the chip like on a full up/down, but without the PHY
statemachine restart.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 48228
This removes one patch which was applied upstream with commit
67b9bcd36906e12a15ffec19463afbbd6a41660e. All other patches were
refreshed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 48203
Some switches can force link speed for a port. Let's add API that will
allow drivers to export this feature.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48142
When building SDK with external toolchain, don't
include _gcc in the filename
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48084
For final output image names allow user to add an
extra string (which is sanitized). This is particularly
useful with ImageBuilder where you may generate multiple
images from the same base and for the same board,
with different package selections and additional files
(via FILES=).
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48083
We allow to configure the version distribution name;
let's also use it for the tarballs (SDK, ImageBuilder,
and SDK).
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48081
Toolchain makefile was missing include of version.mk
so the openwrt version was missing from the filename.
This patch fixes that.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 48080
With the default network config provided by package base-files present,
board_detect won't create a new config from board.json.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 48076
My last bugfix (r47538) introduced a new bug in wndr3700_board_detect
(again...).
Assigning the result of ar71xx_get_mtd_offset_size_format to the model
variable before stripping of garbage using awk will cause all NUL bytes to
be removed before awk is applied, leading to model strings like
"NETGEAR WNDRMACv2NETGEAR", where a NUL byte after the v2 is supposed to
terminate the string.
Fix by calling ar71xx_get_mtd_offset_size_format twice, once piping to awk
directly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 48075
This fixes regression introduced in my recent ledtrig-netdev commit.
Events triggered by different interfaces were stopping timer so it
wasn't working for tx/rx mode.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48072
It was never tested, most likely not working (because of le32_to_cpu)
and not upstreamed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48060
This patch adds support for the Bitmain Antrouter R1
http://wiki.openwrt.org/toh/bitmain/r1
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 48058
linux 4.4 (since commit 08b3c894e56580b8ed3e601212a25bda974c3cc2
"MIPS: lantiq: Disable xbar fpi burst mode") requires that the xbar is
defined in the .dts of vrx200 (VR9) SoCs.
SVN-Revision: 48056
LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 48055
The ppp0 interface is renamed after the connection is established. Due
to a missing NETDEV_REGISTER event, the ledtrig-netdev isn't aware of
the renamed interface and literally ignores the device
(no tx/rx indication, led isn't switched off with 'ifdown wan').
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48048
The P2812HNU-F3 doesn't have usb leds. Only the P2812HNU-F1 has those
leds.
Reported-by: Sylwester Petela <sscapi@gmail.com>
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48043
The leds of the following boards are not renamed due to lack of
manuals/informations:
- ARV7519PW
- ARV7510PW22
- ARV4510PW
The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't
match the leds from the manual or pictures (e.g. there shouldn't be a wps led).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48042
The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to
indicate the current boot state. This patch adds support for such cases.
The existing led sequences should be the same as before.
Boards which are using a led different from power (like TDW89x0) are
changed to switch of the led after boot
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48041
dsl_control (dsl_notify.sh) is the only process which is aware of the
state of the atm/ptm interface. Use the dsl led exclusive for the dsl
line state.
On boards which don't have a distinct internet and a dsl led, let the
netdev status of the atm interface trigger the shared led.
Triggering the shared led according to the status of the ppp interface
isn't suitable, since the led would be switched of if the ppp
connection goes down, but the line is still in sync.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48040
Remove all now double defined leds from the led board file. Use pppoe
as default for all broadband connections, since it's the default in
OpenWrt now.
Rename the the wifi leds to make sure, the not applicable default
values get overwritten.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48038
- ARV7525PW: use the power led as dsl led as done by the stock firmware
- FRITZ3370: use the info led as internet led
- FRITZ7320: use the power led as dsl led as done by the stock firmware
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48037
Use the same led logic and labels as the OEM firmware (red = okay,
blue = failure).
Add the red internet led.
Remove missing usb led workaround. The workaround shouldn't be in the
default configuration.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48036
No need to switch (and keep) on all leds at boot. Use the same led
logic and labels as the OEM firmware (red = okay, blue = failure).
Add the red internet led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48035
Change the name of the .ubi produced to strip out the word 'factory'. This is
mainly due to the fact that there is no difference between the Ventana 'factory'
image vs the standard image.
Name changes from:
openwrt-imx6-ventana-squashfs.nand-factory_<size>.ubi to
openwrt-imx6-ventana-squashfs-nand_<size>.ubi
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48016
Some Ventana boards have a Marvell sky2 GigE controller as eth1 however
assigning the mac address through device-tree is difficult because the
PCI slot can move around depending on board configuration and slot population.
To work around this we add a patch to the sky2 driver to allow accessing its
mac address via a device-tree alias.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48013
On Ventana boards the Gateworks System Controller is the only device on I2C1
(/dev/i2c-0) and it can NAK transfers if it is busy in an ADC loop. Because
this is a multi-function device with several slave addresses it is best to
add retries at the controller level instead of within each slave driver. This
adds a patch that adds 3 retries for i2c transactions only for Ventana boards
and only for I2C1
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48012
This is a backport of a2291badc355d58ead5c19ae0609468947416040 from thermal-soc
accepted upstream.
The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP. Instead
of assuming 85C for passive cooling threshold and 100C for critical base
these thresholds off the thermal gade max CPU temperature:
- passive threshold: max - 10C
- critical threshold: max - 5C
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 48011
Certain board revisions of the GW52xx support an SPI host controller with
a single chip-select going to an off board connector.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 48009
As explained earlier, using SWITCH_TYPE_LINK gives more flexibility,
it doesn't require e.g. string parsing to read some data.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47999
So far we were sending link data as a string. It got some drawbacks:
1) Didn't allow writing clean user space apps reading link state. It was
needed to do some screen scraping.
2) Forced whole PORT_LINK communication to be string based. Adding
support for *setting* port link required passing string and parting
it in the kernel space.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47997
It's not necessary to define PCI_* if pci_ids.h is included a few
lines above.
The change to pci_ids.h doesn't look intentional to me, especially
since the former value is added to the top of ifxmips_fixup_pcie.c.
Both changes were introduced with the kernel 4.1 support patches and
were not present in the 3.18 patches.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47996
Use the same max spi frequency as set in u-boot.
According to the datasheets, the Q64-104HIP as well as the Winbond
25Q64FVSIG support spi frequencies up to 50 MHz. During my tests, the
Q64-104HIP couldn't be recognized/initialized if the frequency
was > 40MHz.
Both chips do support fast read as well.
While touching the dts file, I fixed the dtc compiler warnings.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47994
using the special tag in this way lead to port mirroring for certain types of traffic.
fallback to using th PMAC_EWAN register for the wan portmap.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47993
Previously switching to non-existing device (interface) could result in
leaving LED on.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47990
We may just delete timer on every trigger update and then start it again
if needed. This will let us avoid both: races and locking in frequently
called timer callback.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47987
Read/write lock was adding useless complexity, there wasn't any real
gain in case of this driver.
Also switch to _bh variants to avoid deadlocks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47986
4.1 got little bit larger than 4MB and I couldn't get lzma loader
working on this platform
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 47970
This patch configures the correct ath9k WLAN LED polarity for the TDW8970,
and for the TDW8980 as well.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47969
All supported kernels require patching ledtrig-netdev in the same way,
so it's safe to just move these changes to the base version of this
driver. We needed these patches for some old kernels 2.6.36 and 3.11.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47962
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.
Change the code to still allow boards to opt-out of this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47956
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47952
The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47948
move all library includes and 'firmware already exists'
check to the top of the script.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47947
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47943
Image generation part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47942
Image generation (and mtd partition) part of support for
PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP is a device sold by
PowerCloud Systems who's stock firmware (CloudCommand) provides
'cloud' based managment of large numbers of access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via
PoE or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47941
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47940
Kernel part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47939
Kernel part of support for PowerCloud CAP324 Cloud AP.
The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
the CloudCommand service for 'cloud' based managment of large numbers
access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47938
Commit r47866 dropped default values which were handling WAN interface
at port 0. Fix it by handling 2 more cases on NVRAM values.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47932
Based off of the GW2391-C, but with the following changes:
* 4x4in to 4x5in pcb
* flat panel connector for LED signals
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com>
SVN-Revision: 47920
Still unused, but u-boot doesn't take care of the led, which results in a
permanent switched on 5GHz LED.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47915
- Use common OpenWrt blink patterns instead of custom ones
- Add preinit_regular hook
- Handle the TDW89X0 that does not have a configurable power LED
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47914
This patch configures the correct ath9k WLAN LED polarity for the TDW8970.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47913
The TDW8970 has a AR9381, which is the bgn 3x3:3 variant of the AR938x family.
The TDW8980 has a AR9287, which is the bgn 2x2:2 variant of the AR928x family.
This means that the chip for both routers is 2.4 GHz only.
Anyway, the manufacturer didn't disable the 5 GHz band in the EEPROM partition
(at least on my TDW8970).
So this patch disables the 5 GHz band.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47912
Zero config value for default memory region means 'memory', not
not 'disabled' according to 'Control Registers Of The Coherency
Manager' manual.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47906
Since now we hopefully setup memory regions properly we no longer need this hack.
Tested and works on ubnt-erx.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47905
Only compile tested since I do not have any hardware with
devices on pcie bus.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47904
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
Partitions defined in parent dtsi cannot be undefined in children.
This moves partitions defined in mt7621.dtsi into board's device tree.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47876
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47875
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47851
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.
This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.
This results for a BTHOMEHUBV5A into the following led configuration:
- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"
With the final result of a switched off power led after boot.
The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47850
This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git
Signed off by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47849
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47848
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 47844
* Switches clocksource to gic timer.
* Moves frequency definitions to dtsi since frequency was hardcoded anyway
Will work on proper frequency detection later.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47843
Enables CPS multiprocessing instead ob obsoleted CMP for mt7621.
This patch fixes a few issues currently existing on 4.3 kernel with at least ubnt-erx:
* iperf shows only 50Mbits on direct gigabit connection to desktop,
* ping times jump to 5-6ms to dorectly connected desktop
* /proc/interrupts shows spurious interrups (ERR)
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47842
This resolves compilation warnings like this:
drivers/gpio/gpio-mt7621.c: In function 'mediatek_gpio_probe':
drivers/gpio/gpio-mt7621.c:328:46: warning: passing argument 2 of 'irq_set_chained_handler' from incompatible pointer type [-Wincompatible-pointer-types]
irq_set_chained_handler(mediatek_gpio_irq, mediatek_gpio_irq_handler);
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47841
Change the case switch to reflect the value used in the corresponding
device tree file.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47833
Use kernel arch for dts compilation.
Also use Image/BuildDTB to build dts for ramips.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47823
This replaces old bcm53xx patch for scanning whole flash and makes
bcm47xxpart compatible with NAND.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47800
Starting with r47755 the pppoe wan interface section isn't any longer added to
the network config on firstboot, using the default configuration. Since the
commit message does not mention such a change, I assume that this wasn't
intentionally.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47793
Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware,
we can drop the dsl_fw partition and extend the firmware partition.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47783
Now that IPV6 isn't build as a module anymore, we don't need to decouple
bridge from ipv6 anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47751
In old days mtd_add_partition was checking for partitions overlapping
which was breaking our splitting feature. We had to modify this function
by adding an extra bool dup_check parameter. Upstream commit:
3a434f66e6da ("mtd: part: Remove partition overlap checks")
removed that check so we don't need our modification anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47748
For a long time we have a dedicated firmware splitter for uimage as a
replacement for the one builtin into mtd subsystem. For a year we got a
proper warning for users sticking to the old one (r43700). It should be
really safe to drop it now, especially since we do it for 4.4 only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47747
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47723
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
This migrates the final board.d user of ucidef_add_switch_vlan() to the new
ucidef_add_switch_ports() approach, fixing some logic errors for a few boards
along the way.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47717
Overlayfs stacking was broken in 4.1.12 but now fixed in upstream branch.
Stacking allows experimenting with configurations without the need to
reset a device to factory config.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47714
This patch adds support for the NuCom R5010UNv2.
It's a BCM6328 based board. It has an onboard BCM43217 wifi chip. For this
wifi chip looks like the brcmsmac driver isn't still supported, b43 drivers are used
for the profile of the router.
It's worth mentioning this board was affected by a bug solved with
https://dev.openwrt.org/changeset/46707
Tested-by: Angel Fontan <angel.fontan@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47697
Eth0 is attached to mac0 of the switch with a fixed link and and not to
phy4 in single phy mode, so configuring it to anything but 1000FD will
break the connection, which will happen if a only 100 Mbit capapble device
is plugged into the wan port.
Fix this by not taking the state from phy4 and just configuring a fixed link
for eth0.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47695
