Commit graph

882 commits

Author SHA1 Message Date
John Crispin
055663201b ar71xx: Add Support for the Bitmain Antminer S3
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s3

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46236
2015-07-07 13:46:54 +00:00
John Crispin
9f2b8b3902 ar71xx: allow pci calibration fixup to work with ar9344
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 46235
2015-07-07 13:46:44 +00:00
Felix Fietkau
b26077026f ar71xx: add support for ap143
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>

SVN-Revision: 46208
2015-07-07 08:06:05 +00:00
Felix Fietkau
c9e433206f ar71xx: rework patch for qca953x/956x
Patch cherry-picked from the following location:
https://www.codeaurora.org/cgit/quic/qsdk/oss/system/openwrt/commit/?h=release/coconut_ioe4531_2.0&id=5c357bf6c763e4140dddcc9a3bc5f005525a9c0e

Changelist,
    - add more register defines
    - add EHCI support
    - fix GPIO pin count to 18
    - fix chained irq disabled
    - fix GMAC0/GMAC1 initial
    - fix WMAC irq number to 47
    - merge the changes of dev-eth.c from the patch to file.

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 46207
2015-07-07 08:05:55 +00:00
Felix Fietkau
7acbd52055 ar71xx: fix ethernet initialization on QCA953x-based boards (TP-Link TL-WR841N/ND v9, Compex WPJ531)
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 46206
2015-07-07 08:05:50 +00:00
John Crispin
be755a99d6 ar71xx: add kernel support for EnGenius EPG5000.
Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46047
2015-06-18 18:21:33 +00:00
John Crispin
e85f3471ba ar71xx: add support for TL-WR720N-v4.
The hardware should be almost the same as TL-WR720N-v3.  WiFi and LAN networks
were tested by "Lo Yuk Fai <loyukfai@gmail.com>".  Failsafe and slider switch
were tested by "Wong min <alpha080@gmail.com>".

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 46046
2015-06-18 18:21:23 +00:00
John Crispin
8399be545a ar71xx: add support for compex wpj531
tftpboot 0x80500000 openwrt-ar71xx-generic-wpj531-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 46045
2015-06-18 18:21:15 +00:00
John Crispin
694dd581eb ar71xx: Add Support for the Bitmain Antminer S1
This patch adds support for the Bitmain Antminer S1 Cryptocurrency Miner

http://wiki.openwrt.org/toh/bitmain/s1

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Acked-by: James Hilliard <james.hilliard1@gmail.com>

SVN-Revision: 46044
2015-06-18 18:21:05 +00:00
Felix Fietkau
4a9d726200 ar8216: Fix problem with AR8337 MAC swap handling
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.

Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.

The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 45970
2015-06-14 17:43:50 +00:00
Felix Fietkau
28d8972c25 ar71xx: fix 100/10mbps ethernet link issues on mynet range extender
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.

The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.

The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.

Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 45954
2015-06-14 17:41:01 +00:00
John Crispin
66950455b7 ar71xx: Add support for the Meraki MR12 & MR16
This patch is to add support for the Meraki MR12 and MR16 Access Points.
Currently everything is working, minus the 2nd NIC interface on the MR12
which is built into the SoC.

Signed-off-by: Chris R Blake <chrisrblake93 at gmail.com>

SVN-Revision: 45726
2015-05-23 15:27:22 +00:00
Luka Perkov
2a9ebfb503 ar71xx: add status led found on ew-dorin boards
Signed-off-by: Catrinel Catrinescu <cc@80211.de>

SVN-Revision: 45656
2015-05-10 07:47:04 +00:00
Felix Fietkau
11c588bc96 ar71xx: do general formatting on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45640
2015-05-08 12:24:30 +00:00
Felix Fietkau
d4600d867c ar71xx: fix spelling, add copyright on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45639
2015-05-08 12:24:23 +00:00
Felix Fietkau
b1aea59f08 ar71xx: add support for Green WAN LED on wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45638
2015-05-08 12:24:17 +00:00
Felix Fietkau
aa970f13a3 ar71xx: add support for green LAN LEDS for wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45637
2015-05-08 12:24:11 +00:00
Felix Fietkau
17c78d12bd ar71xx: fix amber WAN LED setting for wnr2000-v4
Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45636
2015-05-08 12:24:03 +00:00
Felix Fietkau
5e1e04e505 ar71xx: make WLAN button RFKILL on wnr2000-v4
Users will now be provided with the inherent wifi toggle functionality
of /etc/rc.button/rfkill

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45635
2015-05-08 12:23:58 +00:00
Felix Fietkau
b1380ebae3 ar71xx: set all buttons to be active_low on wnr2000-v4
Originally pressing a button would trigger a release state and vice-versa,
as observed from hotplug.d.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45634
2015-05-08 12:23:53 +00:00
Felix Fietkau
6413f40e96 ar71xx: fix ethernet on wnr2000-v4
Most people report broken ethernet with upstream. Last year, user "franz.flasch"
authored a working mach-file. His patch is outdated so I modernized it. Original
patch and user commentary on page 1:
https://forum.openwrt.org/viewtopic.php?pid=260861#p260861

I have figured out what the critical differences are between the two that caused
upstream ethernet to break.
  1) Both ath79_init_mac() functions calls must be invocated before any GMAC init
  2) must init GMAC0 before GMAC1

That was enough to get upstream to function, but I wanted to enjoy my confidence
having tested franz's patch for a week sucessfully, so I put his whole
function in, which only features more differences in order of function calls.

An expert should consider these changes, which could pose potential bugs/issues:
1) No longer using the flag AR934X_ETH_CFG_SW_PHY_SWAP in the
ath79_setup_ar934x_eth_cfg() call.

2) Possible consequence of no longer explicitly setting ethernet duplex/speed.

Review: With this patch, my ethernet and wireless works.

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45633
2015-05-08 12:23:45 +00:00
Felix Fietkau
a51f5cace4 ar71xx: use a common naming scheme for LEDS on wnr2000-v4
It is common that the router provider be used rather than product name.
One can see this in target/linux/ar71xx/base-files/etc/uci-defaults/01_leds

Signed-off-by: Michael J. Bazzinotti <mbazzinotti@gmail.com>

SVN-Revision: 45630
2015-05-08 12:23:27 +00:00
Luka Perkov
8084b056e2 ar71xx: fix leds and gpio on wpj344
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45589
2015-04-29 20:04:46 +00:00
Luka Perkov
9d76de9771 ar71xx: add support for compex wpj344
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45527
2015-04-20 20:47:48 +00:00
Felix Fietkau
0a4b20166d ar71xx: Increase RXD/RDV to 2 on OM5P-AN
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45524
2015-04-20 15:01:00 +00:00
Felix Fietkau
f4e6418a32 ar71xx: add a helper function to set RXDV/RXD of ETH_CFG on AR934x
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.

Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45523
2015-04-20 15:00:52 +00:00
Felix Fietkau
5c6925a23b ar71xx: Remove TX/RX delay from pll_1000 for OM5P-AN
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.

Signed-off-by: Sven Eckelmann <sven@open-mesh.org>

SVN-Revision: 45521
2015-04-20 15:00:20 +00:00
John Crispin
efbdc168ff ar71xx: fix ethernet packet loss issues on OM5P-AN
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.

The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45438
2015-04-14 19:00:51 +00:00
Gabor Juhos
d0a6b278db ar71xx: add initial support for RB911G-5HPacD
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45299
2015-04-07 20:04:03 +00:00
Gabor Juhos
96b006eb32 ar71xx: routerboot: export extended wlan data via sysfs
Export the data to make it accessible from user-space.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45298
2015-04-07 20:03:43 +00:00
Gabor Juhos
76b5a9aa7d ar71xx: routerboot: add support for extended radio data
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.

Update the RouterBOOT helper code to support the new
format.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45297
2015-04-07 20:03:35 +00:00
John Crispin
17a1e18ee2 ar71xx: add kernel support for the OpenMesh OM5P-AN board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 44861
2015-03-17 09:43:19 +00:00
John Crispin
7ea781558f ar71xx: fix TP-LINK TL-WDR3600/4300 RFKILL switch positions
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44795
2015-03-15 19:39:47 +00:00
John Crispin
5ca2ad1063 Fix (invert/revert) Hornet-UB WPS LED state
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.

The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.

Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>

SVN-Revision: 44791
2015-03-15 19:25:48 +00:00
John Crispin
3a1a4165b8 ar71xx: Ext LNA patch for TUBE2H and HORNET-UB targets
Signed-off-by: Christophe Prévotaux <c.prevotaux@rural-networks.com>

SVN-Revision: 44693
2015-03-12 10:06:53 +00:00
John Crispin
fd82ffec00 ar71xx: Hornet UB GPIO WPS/Reset
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".

There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:

Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.

The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.

Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>

SVN-Revision: 44692
2015-03-12 10:06:42 +00:00
John Crispin
a0c4419b0d ar71xx: improve WD's My Net Wi-fi Range Extender image creation
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.

Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44665
2015-03-11 15:56:34 +00:00
John Crispin
e5373f2761 ar71xx: rename wrt160nl's trx partition parser
This patch renames the partition parser from
wrt160nl to more generic cybertan.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44663
2015-03-11 15:56:15 +00:00
Luka Perkov
e04e623009 ar71xx: wpj588: add missing usb support
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-By: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 44648
2015-03-10 16:11:39 +00:00
John Crispin
4bc9aad079 ar71xx: Fix LED polarity for the TP-LINK TL-MR13U.
Please also backport to Barrier Breaker (this same patch applies there too).

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 44647
2015-03-10 13:26:50 +00:00
Luka Perkov
b065411a85 ar71xx: add support for compex wpj558
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44620
2015-03-06 14:41:57 +00:00
John Crispin
9358a8a798 ar71xx: TL-WA7210n v2 support
This patch adds support for TP-Link TL-WA7210n[0]

[0] http://www.tplink.com/en/products/details/?model=TL-WA7210N

Signed-off-by: Hendrik Frenzel <hfrenzel@scunc.net>

SVN-Revision: 44526
2015-02-24 12:00:50 +00:00
John Crispin
7e4b3de249 ar71xx: add v3.18 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44456
2015-02-15 19:45:29 +00:00
John Crispin
503a1aaaf6 ar71xx: ZyXEL NBG6716 rfkill switch fix
ZyXEL NBG6716 "rfkill" is a switch, not a button.

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44453
2015-02-14 20:48:42 +00:00
John Crispin
235a83cdfe ar71xx: ZyXEL NBG6716 add gpio usb power on/off
ZyXEL NBG6716 add missing GPIO USB power on/off

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44425
2015-02-13 07:28:53 +00:00
John Crispin
de8d6e447c ar71xx: ZyXEL NBG6716 led/buttons cleanup
ZyXEL NBG6716 led/buttons cleanup
 - improper numbered leds
 - improper named buttons

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44417
2015-02-12 08:07:27 +00:00
John Crispin
b523db36a0 ar71xx: dir-505: fix reset button gpio active_low value
Fix 'active_low' default value for the reset button on DIR-505.

Signed-off-by: Rocco Folino <rocco@devzen.net>

SVN-Revision: 44360
2015-02-09 12:17:00 +00:00
John Crispin
a5b60de253 ar71xx: Add support for MERCURY MAC1200R
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44359
2015-02-09 12:16:51 +00:00
John Crispin
35d38f21e0 ar71xx: fix nbg6716 power and usb led
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Marcin Mikolajczak <gr4ffy@gmail.com>

SVN-Revision: 44358
2015-02-09 12:16:43 +00:00
Luka Perkov
0067ab8e39 ar71xx: rb2011: apply patch to file
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44314
2015-02-07 21:10:51 +00:00