This updates the patches for BCM5354 to the version send for upstream
Linux inclusion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38037
This is now the version which was send for mainline Linux kernel
inclusion. The data needed to detection a board is now stored in init
data.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38036
This patch adds support for Huawei E970 wireless gateway devices.
It has been tested on an E970 labelled as T-Mobile web'n'walk Box IV.
E960/B970 should work too, from what I know it's basically the same hardware.
The device has a Broadcom BCM5354 SoC and a built-in 3G USB modem.
It uses a hardware watchdog which needs GPIO-7 to be toggled at least
every 1-2 seconds. This patch uses gpio_wdt module (see my previous
patch today) to take care of this.
Tested and works: 3G wan, wlan+LED, VLAN config, failsafe using reset
button, image to be used for upgrade from OEM firmware's web interface
Link to the wiki page I've created: <http://wiki.openwrt.org/toh/huawei/e970>
Issue:
* lzma-loader crashes, so gzipped kernel is used. Presumably due to watchdog
reset during kernel decompress.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
SVN-Revision: 38011
A new type of partition with magic FCTY was found on Huawei E970:
46 43 54 59 4b 51 37 4e 41 42 31 38 41 32 39 30 |FCTYKQ7NAB18A290|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38005
This is important patch for new devices that support unaligned
addressing. That devices suffer from the backward-compatibility bug in
DMA engine. In theory we should be able to use old mechanism, but in
practice DMA address seems to be randomly copied into status register
when hardware reaches end of a ring. This breaks reading slot number
from status register and we can't use DMA anymore.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38004
This is based on a patch by Mathias Adam.
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38001
Without this patch it is impossible to read et_swtype, because the 1
byte space is needed for the terminating null byte. Now it should be
possible to read decimal and hex vars of max 8 bit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37999
Most of the bcm47xx devices use TRX format for storing kernel and some
partition like Squashfs or JFFS2. This is pretty flexible solution, CFE
(the bootloader) just writes (and later boots) TRX at some hardcoded
place and paritions can vary in the size.
However some devices don't use TRX format. Very recently we have
discovered ZTE H218N that has kernel and rootfs partitions at some
"random" places.
This patch allows Linux find a rootfs partition after installing custom
image with a CFE bootloader.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37998
* Use different structs depending on the number of nvram variables to check.
* Add detection of ZTE H218N, this closes#14151.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37996
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that
requires initialization. We already have code for this, but because
of the typo in code it was never working. This resulted in network not
working for some routers and possibility of soft-bricking them.
Use correct bit for switch initialization and fix typo in the define.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 37993
This patch adds board detection for the Linksys E1000 V2.1 router, as well
as GPIO support for same.
This fixes bug #14135. Currently, wired networking isn't working on the
router, and I haven't tried the wireless, but with this patch, OpenWRT
successfully boots, and all the LEDs and buttons work properly.
Signed-off-by: Zachary Catlin <zcatlin@indiana.edu>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37977
This uses a new switch driver.
The old ADMTEK Adm6996 switch is not supported any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37650
This is untested, but probably needed to make it work with the phy lib switch driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37649
bcm47xx_nvram_gpio_pin() returns a gpio pin number for a given name based
on configuration data in nvram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 37644
This makes it possible to use swconfig to controll the switch.
This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.
SVN-Revision: 37304
This fixes some problems with the switch handling
* It now send the messages again to indicate a button for failsafe mode should be pressed
* it does not leak packages between wan and lan any more
* the switch works again in normal mode
The Ethernet connection has to be up when the switch driver switch-robo
is insmoded therefor we just do it again.
Explicitly set enable_vlan to prevent leaking packages.
This should close#13869, #13868 and #13716
SVN-Revision: 37286
In order to support both normal images and initramfs, ensure that each
target sets KERNELNAME properly so that the generic kernel building code
can copy the corresponding files over $(KDIR) with the appropriate
extension. Update the various paths to the kernel and wrapper images
from $(LINUX_DIR)/arch/$(ARCH)/boot/$(foo) to $(KDIR)/$(foo).
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 37049
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 36482
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.
Thank you russell for spotting this problem.
SVN-Revision: 36235
WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#".
CFE and NVRAM contain different vars - example:
CFE line original: Device eth0: hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0
CFE after openwrt: Device eth0: hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0
Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html
Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2
(and on wikidevi for example)
Signed off by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 35790
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.
This makes OpenWrt always use vlan1 and vlan2 instead.
SVN-Revision: 35704
This contains the following new bigger changes:
* new partition parser which still could lake some features or have bugs
* new nand flash driver
* using physmap-flash flash driver for parallel flash
* some changes to the serial flash driver
With these changes OpenWrt starts using more of the mainline flash drivers.
SVN-Revision: 35632
Adjust the "AutoLoad" number for the BGMAC module to be prior
to the switch modules. This probably isn't real important as
the modules are loaded in the correct order by preinit anyway.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35625
The included patch will generate a correct network configuration on the simpletech simpleshare.
Thank you for the patch Will Holmes (RealOpty)
This closes#12361.
SVN-Revision: 35623
The mac address should be aligned to u16 to prevent an unaligned access
in drivers/ssb/pci.c where it is casted to __be16.
This closes#9824.
SVN-Revision: 35618
This also removes kmod-ocf, because kmod-crypto-ocf is automatically selected by kmod-ocf-ubsec-ssb.
Thank you Manuel Munz <freifunk@somakoma.de> for the patch.
SVN-Revision: 35509
Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2
in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to
be expanded. Is there a way to determine the correct cpu_port to use in a
generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if
"/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could
a similar method be used in "/etc/init.d/netconfig"?
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35491
The default profile now contains Ethernet drivers for all the types
found on supported boards. There are other profiles for each Ethernet
driver.
SVN-Revision: 35314
Update the default IRQ assignment for unrecognized devices per
the upstream change.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 35121
