Not all kmod packages depends on kmod-ipt-compat-xtables, but this
kernel config option is required for building the whole package
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Commit 2728512 ("e2fsprogs: List all libraries explicitly") forced the
e2fsprogs build system to link libcom_err.so in various places.
Unfortunately, the krb5 package also ships a libcom_err.so with a totally
different ABI and puts it into the global staging directory which causes
e2fsprogs to pick up this wrong library, leading to the following failure:
LD blkid
../lib/libext2fs.so: undefined reference to `_et_list'
collect2: error: ld returned 1 exit status
Makefile:504: recipe for target 'blkid' failed
Change the SYSLIBS specification to explicitely link libcom_err.so.0.0
which in order to work around the problem.
In the long run, the libcom_err clash between e2fsprogs and krb5 needs to
be solved properly.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
"service" is a simple wrapper that will allow to call init.d scripts
current method: # /etc/init.d/network reload
with the wrapper: # service network reload
If the wrapper is called without arguments or with a wrong init script name, it will print an error and list the content of /etc/init.d/ folder
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Based on the submission to the uboot-lantiq repo by Martin Blumenstingl.
Use the ddr_settings.h from the GPL tarball. The NAND boot optimized
one (with memory tuning enabled) doesn't work for the UART boot image.
Use the same mtd layout as the stock u-boot. Add add UBI support.
Use the leds to indicate boot status like it is done with the stock
u-boot. Switch on the red power led if kernel image can't be loaded.
Otherwise switch the green led on.
Make only the ramboot u-boot available. Only this image is required for
the first installation of LEDE.
Signed-off-by: Mathias Kresin <dev@kresin.me>
These properties allow overriding the settings from the EEPROM
which indicate whether a band is enabled or not.
Setting this property is only needed when the RF circuit does not
support the 2.4GHz or 5GHz band while it is enabled nevertheless in the
EEPROM.
These patches will be replaced with a future upstream version which
will introduces an ieee80211 device tree property to disable bands.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
There are two types of swapping the EEPROM data in the ath9k driver.
Before this series one type of swapping could not be used without the
other.
The first type of swapping looks at the "magic bytes" at the start of
the EEPROM data and performs swab16 on the EEPROM contents if needed.
The second type of swapping is EEPROM format specific and swaps
specific fields within the EEPROM itself (swab16, swab32 - depends on
the EEPROM format).
With this series the second part now looks at the EEPMISC register
inside the EEPROM, which uses a bit to indicate if the EEPROM data
is Big Endian (this is also done by the FreeBSD kernel).
This has a nice advantage: currently there are some out-of-tree hacks
(in OpenWrt and LEDE) where the EEPROM has a Big Endian header on a
Big Endian system (= no swab16 is performed) but the EEPROM itself
indicates that it's data is Little Endian. Until now the out-of-tree
code simply did a swab16 before passing the data to ath9k, so ath9k
first did the swab16 - this also enabled the format specific swapping.
These out-of-tree hacks are still working with the new logic, but it
is recommended to remove them. This implementation is based on a
discussion with Arnd Bergmann who raised concerns about the
robustness and portability of the swapping logic in the original OF
support patch review, see [0].
After a second round of patches (= v1 of this series) neither Arnd
Bergmann nor I were really happy with the complexity of the EEPROM
swapping logic. Based on a discussion (see [1] and [2]) we decided
that ath9k should use a defined format (specifying the endianness
of the data - I went with __le16 and __le32) when accessing the
EEPROM fields. A benefit of this is that we enable the EEPMISC based
swapping logic by default, just like the FreeBSD driver, see [3]. On
the devices which I have tested (see below) ath9k now works without
having to specify the "endian_check" field in ath9k_platform_data (or
a similar logic which could provide this via devicetree) as ath9k now
detects the endianness automatically. Only EEPROMs which are mangled
by some out-of-tree code still need the endian_check flag (or one can
simply remove that mangling from the out-of-tree code).
[0] http://www.spinics.net/lists/linux-wireless/msg152634.html
[1] https://marc.info/?l=linux-wireless&m=147250597503174&w=2
[2] https://marc.info/?l=linux-wireless&m=147254388611344&w=2
[3] 50719b56d9/sys/dev/ath/ath_hal/ah_eeprom_9287.c (L351)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
These patches add support for configuring ath9k based devices via
devicetree. This was tested on PCI(e) based devices. This should work
for AHB based devices as well (adding more AHB specific properties may
still be needed) as soon as the ath79 platform is ready to populate the
ath9k wmac via devicetree.
This patchset was accepted upstream, more information can be found on
the linux-wireless list:
https://www.spinics.net/lists/linux-wireless/msg155474.html
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The ESP algorithms in CBC mode require echainiv, so have kmod-ipsec
depend on kmod-crypto-echainiv.
See upstream commit 32b6170ca59ccf07d0e394561e54b2cd9726038c.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This constant was always defined to 0, and recently got removed in
upstream commit a07ea4d9941af5a0c6f0be2a71b51ac9c083c5e5 ("genetlink: no
longer support using static family IDs")
Fixes libnl-tiny builds with latest upstream kernels.
Fixes: d723f2573a ("libnl-tiny: remove include/linux overrides to fix various build issues")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Update fuse+libfuse to upstream 2.9.7. Drop the patch for CVE-2015-3202,
which is already integrated in the newer version. Rework the other patches.
Also switch PKG_SOURCE from @SF to libfuse's github releases.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The 10.1 includes a good many stability fixes related to the effort of
backporting upstream 10.2 firmware. Also enables 802.1q vlan support.
Successfully tested on apu2.
The 10.4 firmwares including new backported code as well as stability
fixes. 10.4 has been tested on Fedora x86-64 platforms, but not on LEDE
specifically since I had issues compiling LEDE for my 9980/9984 AP hardware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Packages that do a killall <cmd> with the same name as the init script
will fail the prerm step when the service isn't running. Do make them
removable without having to restart the service, ignore the return code.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
To make sure we properly restart services on upgrade we need to
call the prerm script of the old package, in case the init script
changes (or vanishes).
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Properly stop/start services on upgrade, but don't change the enabled
state.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Allow scripts from the package to be upgraded to be aware of being
upgraded.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Jo-Philipp Wich <jo@mein.io>
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Use fwtool to extract it, only require metadata to be present if the
platform sysupgrade script sets REQUIRE_IMAGE_METADATA=1
Image metadata is in JSON format and contains a list of supported
devices, along with version information that could be displayed by a UI
later before the actual upgrade happens.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This will be used to append extra information to images which allows the
system to verify if an image is compatible with the system.
The extra data is appended to the end of the image, where it will be
ignored when upgrading from systems that do not process this data yet:
If the image is a squashfs or jffs2 image, the extra data will land
after the end-of-filesystem marker, where it will be overwritten once
the system boots for the first timee.
If the image is a sysupgrade tar file, tar will simply ignore the extra
data when unpacking.
The layout of the metadata/signature chunks is constructed in a way
that the last part contains just a magic and size information, so that
the tool can quickly check if any valid data is present without having
to do a pattern search throughout the full image.
Chunks also contain CRC32 information to detect file corruption, even
when the image is not signed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
SafeLoader is image format used by some TP-LINK devices. This tool
allows extracting selected partitions out of it. It can be used for
sysupgrade.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reboot of 519a199cbc
Which broke other builds.
This time, added compile flags to build only for POWERPC archs
Tested on mpc85xx, ar71xx and bcm2708.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Adds Google's mirror as primary source and kernel.org as fallback.
Same as commit 0d4f02dfd6
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TI wl18xx and wl12xx are Wi-Fi/Bluetooth combo modules
that could be found on different existing boards.
But it is possible to get those modules as a separate
component and use with existing boards as well as
new boards equipped with either module may appear so we
remove dependency on OMAP instead we add dependency on MMC
because this Wi-Fi module uses SDIO interface.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Imre Kaloz <kaloz@openwrt.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Without setting the HSR to the selected channel, the WLAN of the UAP
Outdoor+ will exhibit high packet loss in RX.
Based-on-patch-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
odhcpd daemon has hitless config reload support by means of the
sighup signal; add reload_service function which uses sighup
signal to reload the config
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This fixes building with musl and drops the dependency on the OpenWrt
kernel-header patches:
270-uapi-kernel.h-glibc-specific-inclusion-of-sysinfo.h.patch
271-uapi-libc-compat.h-do-not-rely-on-__GLIBC__.patch
272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch
Use the new upstream location at netfilter.org and use a define instead
of a patch to "optimize".
See also: https://git.netfilter.org/arptables/log/
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
[Jo-Philipp Wich: add mirror SHA256 sum]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This allows to include optimizations such as ARM neon which
are detected on run-time.
Signed-off-by: Nikos Mavrogiannopoulos <nmav@gnutls.org>
[Jo-Philipp Wich: picked from openwrt#191 and rebased onto LEDE master]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds support for "channels" command which displays more details
about channels. It includes e.g. info about available widths.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
A firmware compiled with BUSYBOX_CONFIG_ARP should also use by default the
arp binary from busybox. Otherwise the extra functionality the user
requested can only be used when running arp with the path to the binary.
Signed-off-by: Marek Lindner <marek.lindner@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Backport upstream accepted patch which allows to override the EEPROM
mac address with one from device tree.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 519a199cbc.
Multiple users have reported building failures on ARM architectures, e.g.:
In file included from defs.h:42:0,
from process.c:37:
process.c:51:22: error: 'struct user_regs' has no member named 'ARM_r0'
#define uoff(member) offsetof(struct user, member)
^
./linux/arm/userent.h:1:3: note: in expansion of macro 'uoff'
{ uoff(regs.ARM_r0), "r0" },
^
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to latest Git head in order to import several fixes and enhancements.
- Disable drop invalid by default (FS#73, FS#154)
Instead of dropping packets with conntrack state INVALID, only allow streams
with explicit NEW or UNTRACKED conntrack state.
This change gives user defined rules the chance to accept traffic like ICMPv6
multicast which would be filtered away by the very early ctstate INVALID drop
rule otherwise.
The old behaviour can be restored by explicitely setting "drop_invalid" to 1
in the global firewall config section.
- Fix re-initialization of loadable iptables extensions on musl (FS#31)
Since musl does not implement actual dlclose() semantics, it is impossible to
re-run initializers on subsequent dlopen() calls.
The firewall3 executable now intercepts the extension registration calls
instead in order to be able to re-call them when needed.
This also allowed us to switch to libxtables' builtin extension loader as a
positive side-effect.
- Fix masquerade rules for multiple negated IP addresses (FS#248)
When building MASQUERADE rules for zones which specify multiple negated
addresses in masq_src or masq_dest, emit -j RETURN rules which jump out of
the masquerading chain instead of creating multiple rules with inverted "-s"
arguments.
- Tag own rules using comments
Instead of relying on the nonstandard xt_id match, use the xt_comment match
to mark own rules. Existing comments are prefixed with "!fw3: " while
uncommented rules are marked with a sole "!fw3" string.
This allows removing the xt_id match entirely in a later commit.
- Make missing ubus connection nonfatal
Technically, firewall3 is able to operate without ubus just fine as long as
the zones are declared using "option device" or "option subnet" instead of
"option network" so do not abort execution if ubus could not be connected or
of no network namespace is exported in ubus.
This allows running firewall3 on ordinary Linux systems.
- Fix conntrack requirement detection for indirectly connected zones
The current code fails to apply the conntrack requirement flag recursively to
zones, leading to stray NOTRACK rules which break conntrack based traffic
policing.
Change the implementation to iteratively reapply the conntrack fixup logic
until no more zones had been changed in order to ensure that all directly and
indirectly connected zones receive the conntrack requirement flag.
- Add support for iptables 1.6.x
Adds support for the xtables version 11 api in order to allow building
against iptables 1.6.x
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
"This release fixes a few minor bugs, including a
(non-security-impacting) buffer overflow fix ported
from upstream cjson."
<http://software.es.net/iperf/news.html#iperf-3-1-4-released>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Most of the lantiq devices with ralink wifi have the EEPROM stored
in big endian byte order in flash, but the driver expects the EEPROM to
be in little endian.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The ralink,mtd-eeprom device tree property doesn't require the
ralink,eeprom property to work.
Rework the error handling and user notification as well. Do not log an
error if the mtd-eeprom parameter isn't used. It could be intentional
and should not scare the user.
Check if the number of bytes read from the mtd devices matches the
requested number of bytes.
In case of an mtd read error, give a hint to the user which partition
was tried to read from.
In case everything is fine, notify the user as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Call the rt2x00lib_get_eeprom_file_name only once and from the function
where the EEPROM filename is required.
Error only out if an EEPROM file is mandatory. Use the
REQUIRE_EEPROM_FILE bit to determine if it is mandatory.
Do not set the REQUIRE_EEPROM_FILE bit while requesting an EEPROM file.
It should be (and is) set before requesting an EEPROM file.
Do not redirect users to upstream while using a function of a custom
patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Adds the mac address of the DNS requestor to DNS queries which
are forwarded upstream and can be used to do filtering by the
upstream servers. This only works if the requestor is on the
same subnet as the dnsmasq server
The addmac parameter can hold the following values:
0 : mac address is not added
1 : mac address is added in binary format
base64 : mac address is added base64 encoded
text: : mac address is added in human readable format
as hex and colons
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
moving comgt and its modules to WWAN submenu to join uqmi as both are tools for WWAN modems.
I replaced the link with comgt's ubuntu manpage because the old link isn't working anymore.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Package the driver for the DS1374 chip present on the T4240RDB.
Signed-off-by: Florian Larysch <fl@n621.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [fix missing symbol]
For Huawei devices like E3372 proper command for set lte mode is:
AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Eval is required for proper quotation.
Without this fix:
Fri Nov 4 19:07:49 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> AT
Fri Nov 4 19:07:52 2016 daemon.notice netifd: wan (2060): sending -> ATZ
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATQ0
Fri Nov 4 19:07:53 2016 daemon.notice netifd: wan (2060): sending -> ATV1
Fri Nov 4 19:07:54 2016 daemon.notice netifd: wan (2060): sending -> ATE1
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> ATS0=0
Fri Nov 4 19:07:55 2016 daemon.notice netifd: wan (2060): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:07:57 2016 daemon.notice netifd: wan (2060): sending -> AT^SYSCFGEX=\"03\",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Error running AT-command
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2060): Failed to set operating mode
Fri Nov 4 19:07:58 2016 daemon.notice netifd: wan (2092): Stopping network
...
With this fix:
Fri Nov 4 19:10:59 2016 daemon.notice netifd: Interface 'wan' is setting up now
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> AT
Fri Nov 4 19:11:01 2016 daemon.notice netifd: wan (2539): sending -> ATZ
Fri Nov 4 19:11:02 2016 daemon.notice netifd: wan (2539): sending -> ATQ0
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATV1
Fri Nov 4 19:11:03 2016 daemon.notice netifd: wan (2539): sending -> ATE1
Fri Nov 4 19:11:04 2016 daemon.notice netifd: wan (2539): sending -> ATS0=0
Fri Nov 4 19:11:05 2016 daemon.notice netifd: wan (2539): sending -> AT+CGDCONT=1,"IP","internet"
Fri Nov 4 19:11:06 2016 daemon.notice netifd: wan (2539): sending -> AT^SYSCFGEX="03",3fffffff,2,4,7fffffffffffffff,,
Fri Nov 4 19:11:07 2016 daemon.notice netifd: wan (2539): sending -> AT^NDISDUP=1,1,"internet"
Fri Nov 4 19:11:08 2016 daemon.notice netifd: wan (2539): Connected, starting DHCP on wwan0
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan' is now up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network device 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Network alias 'wwan0' link is up
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is enabled
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' has link connectivity
Fri Nov 4 19:11:08 2016 daemon.notice netifd: Interface 'wan_4' is setting up now
...
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
FS#256
Fix audio not working due to unset SND_PCM_TIMER. CONFIG_SND_PCM_TIMER
is required for ALSA to work (at least for some audio devices),
otherwise applications using sound may fail. Can be reproduced by
installing "alsa-utils-tests" and running "speaker-test":
...
ALSA lib pcm_direct.c:1159:(snd1_pcm_direct_initialize_poll_fd) unable to open timer 'hw:CLASS=3,SCLASS=0,CARD=0,DEV=0,SUBDEV=0'
ALSA lib pcm_dmix.c:1106:(snd_pcm_dmix_open) unable to initialize poll_fd
Playback open error: -19,No such device
The kernel size does not increase, only the size of the kernel module
increases.
Signed-off-by: Dmitry Sutyagin <f3flight@gmail.com>
This reverts commit efd9dec319.
ath10k can take a long time to probe, long enough for netifd to fail to
initialize already configured wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
LEDE no longer requires all PHYs to be initialized to
create the configuration files during bootup. This patch
removes the now obsolete ath10k patch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, the wifi detection script is executed as part of
the (early) boot process. Pluggable wifi USB devices, which
are inserted at a later time are not automatically
detected and therefore they don't show up in LuCI.
A user has to deal with wifi detection manually, or restart
the router.
However, the current "sleep 1" window - which the boot
process waits for wifi devices to "settle down" - is too
short to detect wifi devices for some routers anyway.
For example, this can happen with USB WLAN devices on the
WNDR4700. This is because the usb controller needs to load
its firmware from UBI and initialize, before it can operate.
The issue can be seen on a BT HomeHub 5A as well as soon as
the caldata are on an ubi volume. This is because the ath9k
card has to be initialized by owl-loader first. Which has to
wait for the firmware extraction script to retrieve the pci
initialization values inside the caldata.
This patch moves the wifi configuration to hotplug scripts.
For mac80211, the wifi configuration will now automatically
run any time a "ieee80211" device is added. Likewise
broadcom-wl's script checks for new "net" devices which
have the "wl$NUMBER" moniker.
Issues with spawning multiple interface configuration - in
case the detection script is run concurrently - have been
resolved by using a named section for the initial
configuration. Concurrent configuration scripts will now
simply overwrite the same existing configuration.
A workaround which preserves the "sleep 1" window for just
the first boot has been added. This allows the existing
brcm47xx boot and mvebu uci-default scripts to correctly
setup the initial mac addresses and regulatory domain.
And finally, the patch renames the "wifi detect" into
"wifi config". As the script no longer produces any output
that has to be redirected or appended to the configuration
file.
Thanks to Martin Blumenstingl for helping with the implementation
and testing of the patch.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Previously, wifi detect simply dumped its generated wireless
configuration to STDOUT. A second step was needed to append
the configuration to /etc/config/wireless (or create it, if
it didn't exist).
With this patch, The wifi detection script will now use uci
to update the wireless configuration directly.
This patch also makes the initially created wifi-iface a
named section ('default_radio$X' for mac80211 and
'default_wl$X' for broadcom). With this change, uci will
not print the cfgHASH to STDOUT (which would now corrupt
the wireless configuration). It will also prevent adding
duplicated wifi interface configurations, if the wifi
configuration is run concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds a check in "wifi detect" to test if the wireless
configuration file does exist. If it doesn't exist, an empty
/etc/config/wireless file will be created.
This is necessary because uci doesn't create new files,
instead the tool just exits with "uci: Entry not found".
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rename the "ip" package declaration to "ip-tiny" and let both "ip-tiny" and
"ip-full" provide the virtual "ip" package. This allows users to freely choose
the "ip" command variant while other packages can continue to depend on "ip"
without needing to enforce a specific variant.
Note that this commit does not add busybox as "ip" provider due to
the following reasons:
- The builtin Busybox ip applet cannot be added or removed at runtime
- Both "ip-tiny" and "ip-full" are able to install without file clashes even
if the busybox applet is enabled
- The system is preferring full "ip-tiny" and "ip-full" at runtime, even
if Busybox ip is still present.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The current uboot default config for the A13 SOM erroneously enables support
for the AXP209 power regulator IC which is not present on the board.
This superfluous support module sets an incorrect initial clock frequency and
confuses the kernel, ultimately leading to a boot failure later on.
Properly disable the PMIC support and enable the EHCI support by translating
the deprecated SYS_EXTRA_OPTIONS values into proper SUNXI_NO_PMIC and
USB_EHCI_HCD symbols respectively.
Also rename 002-add-olimex-a13-som.diff to 002-add-olimex-a13-som.patch and
refresh the remaining patches of the series while we're at it.
Reported-by: Mario Fischer <mario-fischer@web.de>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Introduce support for a new [0-9]u@netdev syntax to ucidev_add_switch() to let
board.d network files request default network switch configurations which do
not use tagged CPU ports.
This commit itself has no effect on generated configurations at the moment
since we still emit untagged configurations by default but it allows boards to
opt-out from default tagged configs in case we start emitting tagged settings
by default.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The libblkid probe support in fstools git head requires blkid/blkid.h for
compilation, so add a build dependency on util-linux which provides libblkid.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 47b1ff965b0cb57013b40fbe2bcd7f3c6eb6b606)
Modified after cherry-pick:
FW_MD5SUM in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit ea9e61b8eb61a2e362a50541f03466dc7d087947)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
We need to tell hwclock with -u commandline option, that we would like
to keep our RTC clock in UTC timezone. Linux kernel expects RTC in UTC
timezone anyway.
In current state of things, we don't tell hwclock to load/store time
from/to RTC in UTC timezone so it uses the timezone from the system
time. If it's set to different timezone then UTC, sysfixtime is going to
screw the time in RTC.
I've following in the setup script:
uci set system.@system[0].timezone='CET-1CEST,M3.5.0,M10.5.0/3'
uci set system.@system[0].zonename='Europe/Prague'
I've this RTC setup (rtc1 is RTC on i.MX6 SoC, rtc0 is battery backed RTC mcp7941x):
rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
Then we can experience following (current time is 10:15am):
$ date
Fri Oct 21 10:15:07 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 08:14:46 2016 0.000000 seconds
$ hwclock -u -r -f /dev/rtc0
Fri Oct 21 10:14:46 2016 0.000000 seconds
And after current broken sysfixtime:
$ /etc/init.d/sysfixtime stop
$ date
Fri Oct 21 10:15:25 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 10:15:31 2016 0.000000 seconds
Now we've time in our battery backed RTC in CEST timezone instead of
UTC. Then once again, but with this patch applied to sysfixtime, where
hwclock is using correctly the -u parameter:
$ /etc/init.d/sysfixtime stop
$ date
Fri Oct 21 10:15:53 CEST 2016
$ hwclock -r -f /dev/rtc0
Fri Oct 21 08:15:55 2016 0.000000 seconds
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Ensure that selecting the wpa-supplicant-mesh package actually packages the
wpa_supplicant binary with SAE support and add missing dependency on OpenSSL.
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: slightly reword commit message for clarity]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
We add an 'httpauth' section type that contains the options:
prefix: What virtual or real URL is being protected
username: The username for the Basic Auth dialogue
password: Hashed (crypt()) or plaintext password for the Basic Auth dialogue
httpauth section names are given included as list
items to the instances to which they are to be applied.
Further any existing httpd.conf file (really whatever
is configured in the instance, but default of
/etc/httpd.conf) is appended to the per-instance httpd.conf
Signed-off-by: Daniel Dickinson <lede@cshore.thecshore.com>
During reload, we could send invalid information to the other
side and confuse it.
That's why, during reload we'll pause execution, do the reconfig
and resume + update when reload is done.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The problem is that interfaces are specified at start as
command line arguments, making them unchange-able via reload.
That means, we have to move (since lldpd allows this) the
interfaces-match-pattern option to be in a config file and reload
the configuration.
It's either that, or do a 'restart'.
Since we're generating the lldpd.conf file, we'll have to
move the 'sysconfdir' of lldpd to /tmp, where the files will
get written ; this will prevent any unncessary flash writes.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Capitalized "disc" submenu name as all submenu names are capitalized (apart from "database", but I'll fix that
later).
moved "swap-utils" to Filesystem submenu as it is "formatting" a partition as swap so it looks out of place in Disc.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Currently the reset script will try to run jffs2reset on boards that are
running a rw rootfs, such as ext4. This will cause jffs2reset to fail
and the board to never reboot while the LED blinks until a manual
reboot.
This commit does two different things:
1. Disables reset on boards that do not have an overlay mount
2. Disables the Blinking LED after 5 seconds if the board does not
support reset
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Fix the default value for the 'bootcmd' environment variable.
Therefore make the default bootcmd work for buildbot's images.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Adds support in uci for configuring multiple dnsmasq instances via
multiple dnsmasq sections.
The uci sections host, boot, mac, tag, vendorclass, userclass,
circuitid, ... will refer to a dnsmasq instance via the instance
parameter defined in the section; if the instance parameter is
not specified backwards compatibility is preserved.
Start/Stopping a dnsmasq instance can be achieved by passing the
dnsmasq instance name as argument to start/stop via the init script.
Multiple dnsmasq instances is usefull in scenarios where you want to
bind a dnsmasq instance to an interface in order to isolate networks.
This patch is a rework of a multiple dnsmasq instance patch by Daniel Dickinson
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Fix metadata scan failure in the grub2 package by removing an unexpected
invisible space character and by adding back the missing SECTION variable
which was removed with d140648.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add a partially random O= item to the certificate subject in order
to make the automatically generated certificates' subjects unique.
Firefox has problems when several self-signed certificates
with CA:true attribute and identical subjects have been
seen (and stored) by the browser. Reference to upstream bugs:
https://bugzilla.mozilla.org/show_bug.cgi?id=1147544https://bugzilla.mozilla.org/show_bug.cgi?id=1056341https://bugzilla.redhat.com/show_bug.cgi?id=1204670#c34
Certificates created by the OpenSSL one-liner fall into that category.
Avoid identical certificate subjects by including a new 'O=' item
with CommonName + a random part (8 chars). Example:
/CN=LEDE/O=LEDEb986be0b/L=Unknown/ST=Somewhere/C=ZZ
That ensures that the browser properly sees the accumulating
certificates as separate items and does not spend time
trying to form a trust chain from them.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Prefer the old default 'px5g' for certificate creation
as Firefox seems to dislike OpenSSL-created certs.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This option, defined by RFC3442, allows a DHCP server to send static
routes to a client. But the client has to request this option
explicitely.
Static routes are useful when the gateway configured by DHCP cannot be
in the same subnet as the client. This happens, for instance, when
using DHCP to hand out addresses in /32 subnets.
A new configuration option "classlessroute" is available, allowing
users to disable this feature (the option defaults to true).
Other DHCP clients already request this option by default (dhcpcd, for
instance, and possibly Windows). If a DHCP server does not support
this option, it will simply ignore it.
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
moved px5g-standalone to Encryption submenu of Utilities.
Fixed title by removing the first "standalone" word from title.
The name is now consistent with other px5g packages, it is also shorter and will be shown in make menuconfig.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
moved px5g to Encryption submenu of Utilities, in an effort to tidy up a bit the Utilities section of make menuconfig.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
mkfs.ext4 und losetup are needed for sysupgrade support on mmc devices
with automatic rootfs split (loopback device usage).
Signed-off-by: André Valentin <avalentin@marcant.net>
