This callback should have one parameter less, this parameter is not used
so this was not a so big problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not
overwrite them to compile the host tools against the shipped LibreSSL.
In addition add a patch to fix a compile problem when compiling the
tools against LibreSSL caused by differences in the API between OpenSSL
1.1 and LibreSSL.
This should fix the compile problems seen in build bot from time to time
by not depending on the host libssl-dev package any more but using the
LibreSSL version from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
mwlwifi was updated to a new stable. Included in this stable release are the
followin benefits:
- Fixed compiling for kernel 4.14
- Fixed crash on 88W8864 binary
Compiled and tested on: WRT3200ACM and WRT1900AC
Signed-off-by: Gabe Rodriguez <lifehacksback@gmail.com>
Option --client-cert-not-required DEPRECATED is deprecated in v2.4 and removed in OpenVPN 2.5.
Replaced by param --verify-client-cert none|optional|require in v2.4 see
https://community.openvpn.net/openvpn/wiki/ DeprecatedOptions#a--client-cert-not-required
Signed-off-by: Christian Bayer <cave@cavebeat.org>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_ RELEASE increase]
This patch adds support for Cisco Meraki MR33
hardware highlights:
SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
1 x Orange LED Fault Indicator (shared with LP5562)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
AT24C64 8KiB EEPROM
Kensington Lock
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
1x4 0.1" header with half-height/low profile pins.
The pinout is: VCC (little white arrow), RX, TX, GND.
Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>
Add images to do an installation via bootloader:
0. open up the MR33 and connect the serial console.
1. start the 2nd stage bootloader transfer from client pc:
# ubootwrite.py --write=mr33-uboot.bin
(The ubootwrite tool will interrupt the boot-process and hence
it needs to listen for cues. If the connection is bad (due to
the low-profile pins), the tool can fail multiple times and in
weird ways. If you are not sure, just use a terminal program
and see what the device is doing there.
2. power on the MR33 (with ethernet + serial cables attached)
Warning: Make sure you do this in a private LAN that has
no connection to the internet.
- let it upload the u-boot this can take 250-300 seconds -
3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
(the u-boot is listening on 192.168.1.1)
# tftp 192.168.1.1
binary
put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin
4. wait for it to reboot
5. connect to your MR33 via ssh on 192.168.1.1
For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)
Thanks to Jerome C. for sending an MR33 to Chris.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Not all LED driver are using the label devicetree property for the led
name. Add support for the TI/National Semiconductor LP55xx Led Drivers,
which are using the chan-name property for the led name, as fallback.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add a fucntion to get the a binary mac address from file. Use the new
function for mtd_get_mac_binary() to limit duplicate code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the patch that was posted to ath10k-devel ML:
<https://patchwork.kernel.org/patch/10233491/>
|From: Thomas Hebb <tommyhebb@gmail.com>
|Subject: [PATCH] ath10k: search all IEs for variant before falling back
|Date: Wed, 21 Feb 2018 11:43:39 -0500
|[...]
|This patch fixes the issue by first searching the entire file for the ID
|with variant, and searching for the fallback ID only if that search
|fails. It also includes some code cleanup in the area, as
|ath10k_core_fetch_board_data_api_n() no longer does its own string
|mangling to remove the variant from an ID, instead leaving that job to a
|new flag passed to ath10k_core_create_board_name().
|
|I've tested this patch on a QCA4019 and verified that the driver behaves
|correctly for 1) both fallback and variant BDFs present, 2) only fallback
|BDF present, and 3) no matching BDFs present.
|
|Fixes: 1657b8f84ed9 ("ath10k: search SMBIOS for OEM board file extension")
|Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Note: 937-ath10k-calibration-variant.patch has been reassigned a new 081
number, as it now ships with upstream.... But also because this patch
requires the change in ath10k_core_create_board_name().
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
libext2fs breaks krb5 by always installing its own copies of libcom_err.so
and libss.so.
Move the libraries into separate libcomerr and libss packages respectively
and add a host build recipe to stage the required compile_et and mk_cmds
utilities for use by other packages.
This allows the krb5 package to be fixed to use the system wide libcomerr
and libss libraries.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[rename libcom_err to libcomerr, make compile_et and mk_cmds relocatable,
cleanup makefile, add dependency on host build, reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Support configuration in the form...
list ip6prefix 2001:db8:1234::/64
list ip6prefix 2001:db8:5678::/64
... to allow specifying multiple routed IPv6 prefixes.
Implements feature request FS#1361.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
1f5a29c ip: do not add local routes for host dependencies
c06f842 device: add support for setting the isolate options for bridge ports
69aeaab interface-ip: fix route selection for host dependencies
Signed-off-by: Felix Fietkau <nbd@nbd.name>
busybox tries to be smart and passes a number of additional flags to the
compiler. Unfortunately, the i386-specific flags break ABI compatiblity
with libc.
Fixes busybox crashes observed on x86-generic with GCC 7.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9984.
The update fixes "ath10k_pci 0001:01:00.0: Invalid VHT mcs 15 peer
stats" spamming the kernel ring buffer at very high frequencies, but
introduces the new "ath10k_pci 0001:01:00.0: Unknown eventid: 36925".
This new warning doesn't appear to cause problems in practice and is
only emitted relatively rarely, not causing dmesg to overflow within
minutes.
Tested on the ZyXEL NBG6817; early feedback also suggests this firmware
to work well (with the same fixes and caveats) on the Netgear r7800 as
well.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This patch updates ath10k-firmware to last commit and use the
firmware-5.bin_10.4-3.5.3-00053 firmware for the QCA9888.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
392811a ubus: let fw3_ubus_address() return the number of resolved addresses
359adcf options: emit an empty address item when resolving networks fails
503db4a zones: disable masq when resolving of all masq_src or masq_dest items failed
f50a524 helpers: implement explicit CT helper assignment support
a3ef503 zones: allow per-table log control
8ef12cb iptables: fix possible NULL pointer access on constructing rule masks
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The default fragment low/high thresholds are 3 and 4 MB. On devices with
only 32MB RAM, these settings may lead to OOM when many fragments that
cannot be reassembled are received. Decrease fragment low/high thresholds
to 384 and 512 kB on devices with less than 64 MB RAM.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In addition to removing redundant code, this fixes various issues in
IB-generated images that have been fixed in prepare_rootfs before,
including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts
from FILES.
We also reuse the opkg macro and remove --force-... flags that have been
removed from rootfs.mk as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Many packages use the opkg conffiles field to list configuration files that
are to be retained on upgrades. Make this work on systems without opkg.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The package still leaks some user space linker options into the kernel
space. This breaks the build when ASLR is activated, deactivate it for
now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
7c0d711 version: bump snapshot
b6a5cc0 contrib: add extract-handshakes kprobe example
37dc953 wg-quick: if resolvconf/run/iface exists, use it
1f9be19 wg-quick: if resolvconf/interface-order exists, use it
4d2d395 noise: align static_identity keys
14395d2 compat: use correct -include path
38c6d8f noise: fix function prototype
302d0c0 global: in gnu code, use un-underscored asm
ff4e06b messages: MESSAGE_TOTAL is unused
ea81962 crypto: read only after init
e35f409 Kconfig: require DST_CACHE explicitly
9d5baf7 Revert "contrib: keygen-html: rewrite in pure javascript"
6e09a46 contrib: keygen-html: rewrite in pure javascript
e0af0f4 compat: workaround netlink refcount bug
ec65415 contrib: embedded-wg-library: add key generation functions
06099b8 allowedips: fix comment style
ce04251 contrib: embedded-wg-library: add ability to add and del interfaces
7403191 queueing: skb_reset: mark as xnet
Changes:
* queueing: skb_reset: mark as xnet
This allows cgroups to classify packets.
* contrib: embedded-wg-library: add ability to add and del interfaces
* contrib: embedded-wg-library: add key generation functions
The embeddable library gains a few extra tricks, for people implementing
plugins for various network managers.
* crypto: read only after init
* allowedips: fix comment style
* messages: MESSAGE_TOTAL is unused
* global: in gnu code, use un-underscored asm
* noise: fix function prototype
Small cleanups.
* compat: workaround netlink refcount bug
An upstream refcounting bug meant that in certain situations it became
impossible to unload the module. So, we work around it in the compat code. The
problem has been fixed in 4.16.
* contrib: keygen-html: rewrite in pure javascript
* Revert "contrib: keygen-html: rewrite in pure javascript"
We nearly moved away from emscripten'ing the fiat32 code, but the resultant
floating point javascript was just too terrifying.
* Kconfig: require DST_CACHE explicitly
Required for certain frankenkernels.
* compat: use correct -include path
Fixes certain out-of-tree build systems.
* noise: align static_identity keys
Gives us better alignment of private keys.
* wg-quick: if resolvconf/interface-order exists, use it
* wg-quick: if resolvconf/run/iface exists, use it
Better compatibility with Debian's resolvconf.
* contrib: add extract-handshakes kprobe example
Small utility for extracting ephemeral key data from the kernel's memory.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (git log --oneline description)
6e744662 Update bash_completion
478eac09 Update manual pages
88e2029e Bump up version number to 1.31.0, LT revision to 30:0:16
45d76cf5 nghttpx: Close listening socket on graceful shutdown
54573f28 Merge pull request #1137 from nghttp2/session-set-user-data
17793e99 Add nghttp2_session_set_user_data() public API function
5eac3c90 Update manual pages
e70195ae nghttpx: Update doc
fe51e7fa Merge pull request #1130 from nghttp2/avoid-inet_pton-macro
eb951c2c src: Define nghttp2_inet_pton wrapper to avoid inet_pton macro
39f0ce7c Merge pull request #1126 from nghttp2/nghttpx-expired-client-cert
65157811 Merge pull request #1123 from nghttp2/mruby-client-cert-not-before-after
e8af7afc nghttpx: Add an option to accept expired client certificate
38abfd18 nghttpx: Add mruby tls_client_not_before, and tls_client_not_after
ff3edc09 nghttpx: Fix potential memory leak
0bb15406 Bump up version number to 1.31.0-DEV
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The lantiq components still leak some user space linker options into the
kernel space. This breaks with build when ASLR is activated, deactivate
it for now on these packages.
Fixes: FS#1391
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not leak the user space CFLAGS into the kernel space any more, this
allows us to activate the MIPS16 build.
This decreases the size of the ipk file from 87589 bytes to 81267 bytes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not force to build with O3 optimization any more, but take what was
selected by the OpenWrt build system.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The build process does not leak the user space cflags into the kernel
build process any more, this allows to activate MIPS16 builds.
This was fixed with some update of ifxos.
This decreases size of the libifxos.a and the ltq-vdsl-app
old:
78320 libifxos.a
44383 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk
new:
66852 libifxos.a
43506 ltq-vdsl-app_4.17.18.6-2_mips_24kc.ipk
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The split-up into packages gre, grev4 and grev6 causes confusion for the
users as reported in FS#1399.
As IPv4 and IPv6 are considered now as bundled; squash the grev4 and grev6
packages into the gre package and let gre provide both grev4 and grev6.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Fixes the assumption the busybox udhcpc applet is always enabled; in case
the symbolic link check fails the DHCP shell handler script will exit and
as result the DHCP protocol handler will not be registered in netifd.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This is to simplify maintenance. It's easy to say now which patches need
some extra work and/or sending upstream. Updating to newer backports
should be also simpler with this.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit 79a768a90f.
Some devices can go over their power limits with this commit, so this
needs to be handled on a case by case basis instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There was a mismatch between indicating factory reset and code actually
starting it. After 5 seconds status LED started blinking rapidly letting
user know it's ready to release reset button. In practice button had to
stay pressed for another second in order to relly start the process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Remove RPS/XPS support from netifd core, move the logic to a hotplug
script that uses a different policy which provides better performance
and more fairness across flows
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Support config in the form of ....
add_list sendopts=router:10.10.10.2
add_list sendopts=nissrv:20.20.20.2
add_list sendopts=0x7D:abba
This allows to configure sendopts having white spaces as option value
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
With this, `mount -t efivarfs` is available and tools such as efitools
and efibootmgr will be usable.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
[daniel@makrotopia.org: some whitespace fixes, match From: with SoB]
As each mvebu device only uses one of the firmwares provided by mwlwifi
package, it makes sense to put them in separate packages and only install
the one that is needed.
Current mwlwifi version's firmware sizes and usages by devices:
88W8864.bin 118776 caiman, mamba, cobra, shelby
88W8897.bin 489932 (none)
88W8964.bin 449420 rango
Changes by this commit:
* indicate in title that mwlwifi also is driver for 88W8897 and 88W8964
* remove mwlwifi package's firmware installation rules
* add 3 new individual firmware packages (all depends on kmod-mwlwifi):
- mwlwifi-firmware-88w8864
- mwlwifi-firmware-88w8897
- mwlwifi-firmware-88w8964
* add firmware package to mvebu devices' DEVICE_PACKAGES accordingly
Signed-off-by: Johnny S. Lee <_@jsl.io>
[Add the used FW files to the PACKAGES of default image]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow building perf on uncommon targets again.
Depending on the kernel version, not all of these archs will actually use
libunwind in perf. Still, it seems simpler and less error-prone to use the
same list that is defined in the libunwind package.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Works around two incompatiblities between glibc and (POSIX-compliant) musl:
- missing register definitions from asm/ptrace.h
- non-POSIX-compliant ucontext_t on PPC32 with glibc
Compile tested on mpc85xx.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Support configuration in the form...
list ip6prefix 2001:db8:1234::/64
list ip6prefix 2001:db8:5678::/64
... to allow specifying multiple additional IPv6 prefixes.
Implements feature request FS#1361.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
As indicated in #5574 samba fails to build with linker error due to lack
of talloc_* functions when the packet libtalloc also gets build.
According to Makefile it is compiled with "--without-libtalloc" option.
Running ./configure --help shows that there is another option connected
to libtalloc: --enable/disable-external-libtalloc.
Adding this option fixes build.
Signed-off-by: Jakub Tymejczyk <jakub@tymejczyk.pl>
Remove this old patch which prevents showing the xfrm ports for SCTP
This was added in commit 60c1f0f64d ("finally move buildroot-ng to trunk")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
62d52e9 mt76: set RX_FLAG_DUP_VALIDATED for A-MPDU reordered packets
5ba5995 mt76x2: rework tx power handling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
459b6932 policy: add nft translation for simple policy none/strict use case
255e55b7 tests: xlate-test: no need to require superuser privileges
6990bbc5 extensions: hashlimit: remove space before burst in translation to nft
13ecaeb0 extensions: hashlimit: Rename 'flow table' keyword to meter
c252a2b0 extensions: Add test for cluster nft translation
bda1daa4 extensions: ip6t_{S,D}NAT: add more tests
88fa4543 extensions: ip6t_{S,D}NAT: multiple to-dst/to-src arguments not reported
64a0e098 extensions: libxt_cluster: Add translation to nft
6067208f extensions: add support for 'srh' match
0f387b07 extensions: hashlimit: fix incorrect burst in translations
1ffe6a74 extensions: libxt_hashlimit: Do not print default timeout and burst
27de281d extensions: Add macro _DEFAULT_SOURCE.
75364151 iptables: Remove const qualifier from struct option.
8b0da213 iptables: masquerade: add randomize-full support
e64db006 iptables: patch to correct linker flag sequence
033eac81 extensions: libxt_tcpmss: Add test case for invalid ranges.
505bfa11 iptables: xtables-eb: Remove const qualifier from struct option
a6d6821a iptables: extensions: Fix MARK target help
71de414c libxt_sctp: fix array out of range in print_chunk
1a32381a extensions: add tests for ipcomp protocol
4bd51770 tests: xlate: print output in same way as nft-test.py
d0e3d95f libxt_recent: Remove ineffective checks for info->name
23e6ed71 libxt_TOS: add tests for translation infrastructure
9564595e Update .gitignore
bebce197 iptables: iptables-compat translation for TCPMSS
dbbab0aa extensions: libxt_tcpmss: Detect invalid ranges
0e958281 iptables-translate: add test file for TCPMSS extension
de3c68b6 iptables-compat: do not allow to delete populated user define chains
f4b80ce7 iptables: change large file support handling
f5b46c2f iptables: Constify option struct
21ba5b38 ip{,6}tables-restore: Don't accept wait-interval without wait
60e0ffd3 ip{,6}tables-restore: Don't ignore missing wait-interval value
af468b6e utils: Add a man page for nfnl_osf
1773dcaa utils: nfnl_osf: Fix synopsis in help text
895ce096 extensions: libxt_bpf: fix missing __NR_bpf declaration
3c633296 xtables-compat-restore: fix translation of mangle's OUTPUT
1c32e560 netfilter: xt_hashlimit: add rate match mode
b5331f88 xtables-compat: fix memory leak when listing
91ae12e3 xtables-compat-restore: fix several memory leaks
79e1edd1 iptables-xml: Fix segfault on jump without a target
c49a93f1 xtables-translate: fix double space before comment
79fa7cc2 libip6t_icmp6: xlate: remove leftover space
8e62f572 tests: xlate: generalize owner
8d994bcf iptables: Add file output option to iptables-save
f8e5ebc5 iptables: Fix crash on malformed iptables-restore
80d8bfaa iptables: insist that the lock is held.
c29d99c8 libxtables: Display weird character warning for wildcards
1fe96cfb tests: xlate: check if it is being run as root
3f92b259 tests: xlate: remove python 3.5 dependency
d89dc47a iptables-restore/save: exit when given an unknown option
65801d02 iptables-restore.8: document -w/-W options
9cd3adbe iptables-restore/ip6tables-restore: add --version/-V argument
1ec1fb7a extensions: libxt_hashlimit: fix 64-bit printf formats
27f69f4a iptables: extensions: Remove typedef in struct.
340105fa tests: add regression tests for xtables-translate
b669e184 extensions: libxt_TOS: Add translation to nft
b2a84476 iptables: Remove unnecessary braces.
2963a8df iptables: Remove explicit static variables initalization.
1cf4ba6f iptables: Constify option struct
999eaa24 iptables-restore: support acquiring the lock.
6e2e169e iptables: remove duplicated argument parsing code
836846f0 iptables: move XT_LOCK_NAME from CFLAGS to config.h.
b91af533 iptables: set the path of the lock file via a configure option.
0e94eb2e iptables-translate: print nft iff there are more expanded rules to print
48ad179b libxtables: abolish AI_CANONNAME
9f50bbdf libxtables: remove unnecessary nesting from host_to_ip(6)addr
c6df55d6 iptables-translate: print nft command for each expand rules via dns names
82dacbb8 xtables-translate: Avoid querying the kernel
9f972f45 extensions: libxt_addrtype: Add translation to nft
2c8e251e utils: nfsynproxy: fix build with musl libc
9b8cb756 libiptc: don't set_changed() when checking rules with module jumps
eb66632d extensions: libxt_hashlimit: Add translation to nft
72bb3dbf xshared: using the blocking file lock request when we wait indefinitely
24f81746 xshared: do not lock again and again if "-w" option is not specified
fc3c3b4e libxt_hashlimit: add new unit test to catch kernel bug
516d9191 iptables: update pf.os
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
This makes it possible to add an iptables rule that offloads routing/NAT
packet processing to a software fast path. This fast path is much
quicker than running packets through the regular tables/chains.
Requires Linux 4.14
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This only works with nftables for now, iptables support will be added
later. Includes a number of related upstream nftables improvements to
simplify backporting follow-up changes
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If the auth or assoc request was denied the reason
was always WLAN_STATUS_UNSPECIFIED_FAILURE.
That's why for example the wpa supplicant was always
trying to reconnect to the AP.
Now it's possible to give reasoncodes why the auth
or assoc was denied.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add Wireless Network Management (IEEE 802.11v)
support to:
- hostapd-full
- wpa_supplicant-full
It must be enabled at runtime via UCI with:
- option ieee80211v '1'
Add UCI support for:
- time_advertisement
- time_zone
- wnm_sleep_mode
- bss_transition
Signed-off-by: Lorenzo Santina <lorenzo.santina@edu.unito.it>
Neighbor reports are enabled implicitly on use, beacon reports and BSS
transition management need to be enabled explicitly
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is fixing multiple compile problems with kernel 4.14 and updates the
code to take care of changes introduced between kernel 4.9 and 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.
Update the u-boot lantiq Makefile to be compatible with the new names as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With upstream commit 2c93e790e825 ("usb: add CONFIG_USB_PCI for system
have both PCI HW and non-PCI based USB HW") the CONFIG_USB_PCI was
introduced.
The option is disabled by default in our generic kernel 4.14 config, hence
we need to set the option for all related kernel modules.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With a9772285a724 ("linux/compiler.h: Split into compiler.h and
compiler_types.h") compiler.h was refactored and most its content was
moved to compiler_types.h. Both files are required to build ppp-mod-pppoa.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The current implementation only checked if uqmi itself executed
correctly which is also the case when the returned value is actually
an error.
Rework this, checking that CID is a numeric value, which can only
be true if uqmi itself also executed correctly.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
1721453 Remove special handling of A-for-A queries.
499d8dd Fix boundary for test introduced in 3e3f1029c9ec6c63e430ff51063a6301d4b2262
6f1cbfd Fix debian/readme typo.
55ecde7 Inotify: Ignore backup files created by editors
6b54d69 Make failure to chown() pidfile a warning.
246a31c Change ownership of pid file, to keep systemd happy.
83e4b73 Remove confusion between --user and --script-user.
6340ca7 Tweak heuristic for initial DNSSEC memory allocation.
baf553d Default min-port to 1024 to avoid reserved ports.
486bcd5 Simplify and correct bindtodevice().
be9a74d Close Debian bug for CVE-2017-15107.
ffcbc0f Example config typo fixes.
a969ba6 Special case NSEC processing for root DS record, to avoid spurious BOGUS.
f178172 Add homepage to Debian control file.
cd7df61 Fix DNSSEC validation errors introduced in 4fe6744a220eddd3f1749b40cac3dfc510787de6
c1a4e25 Try to be a little more clever at falling back to smaller DNS packet sizes.
4fe6744 DNSSEC fix for wildcard NSEC records. CVE-2017-15107 applies.
3bd4c47 Remove limit on length of command-line options.
98196c4 Typo fix.
22cd860 Allow more than one --bridge-interface option to refer to an interface.
3c973ad Use SIGINT (instead of overloading SIGHUP) to turn on DNSSEC time validation.
faaf306 Spelling fixes.
c7e6aea Change references to gPXE to iPXE. Development of EtherBoot gPXE was always development of iPXE core developer Michael Brown.
e541245 Handle duplicate RRs in DNSSEC validation.
84a01be Bump year in Debian copyright notice.
d1ced3a Update copyrights to 2018.
a6cee69 Fix exit code from dhcp_release6.
0039920 Severely fix code formating of contrib/lease-tools/dhcp_release6.c
39d8550 Run Debian startup regex in "C" locale.
ef3d137 Fix infinite retries in strict-order mode.
8c707e1 Make 373e91738929a3d416e6292e65824184ba8428a6 compile without DNSSEC.
373e917 Fix a6004d7f17687ac2455f724d0b57098c413f128d to cope with >256 RRs in answer section.
74f0f9a Commment language tweaks.
ed6bdb0 Man page typos.
c88af04 Modify doc.html to mention git-over-http is now available.
ae0187d Fix trust-anchor regexp in Debian init script.
0c50e3d Bump version in Debian package.
075366a Open inotify socket only when used.
8e8b2d6 Release notes update.
087eb76 Always return a SERVFAIL response to DNS queries with RD=0.
ebedcba Typo in printf format string added in 22dee512f3738f87539a79aeb52b9e670b3bd104
0954a97 Remove RSA/MD5 DNSSEC algorithm.
b77efc1 Tidy DNSSEC algorithm table use.
3b0cb34 Fix manpage which said ZSK but meant KSK.
aa6f832 Add a few DNS RRs to the table.
ad9c6f0 Add support for Ed25519 DNSSEC signature algorithm.
a6004d7 Fix caching logic for validated answers.
c366717 Tidy up add_resource_record() buffer size checks.
22dee51 Log DNS server max packet size reduction.
6fd5d79 Fix logic on EDNS0 headers.
9d6918d Use IP[V6]_UNICAST_IF socket option instead of SO_BINDTODEVICE for DNS.
a49c5c2 Fix search_servers() segfault with DNSSEC.
30858e3 Spaces in CNAME options break parsing.
Refresh patches.
Remove upstreamed patches:
250-Fix-infinite-retries-in-strict-order-mode.patch
260-dnssec-SIGINT.patch
270-dnssec-wildcards.patch
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The default receive window size in dropbear is hardcoded to 24576 byte
to limit memory usage. This value was chosen for 100Mbps networks, and
limits the throughput of scp on faster networks. It also severely limits
scp throughput on high-latency links.
Add an option to set the receive window size so that people can improve
performance without having to recompile dropbear.
Setting the window size to the highest value supported by dropbear
improves throughput from my build machine to an APU2 on the same LAN
from 7MB/s to 7.9MB/s, and to an APU2 over a link with ~65ms latency
from 320KB/s to 7.5MB/s.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Between mbedtls 2.6.0 and 2.7.0, the void returning mbedtls_MODULE* functions
were deprecated in favor of functions returning an int error code. Use
the new function mbedtls_sha256_ret().
Signed-off-by: Russell Senior <russell@personaltelco.net>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Between mbedtls 2.6.0 and 2.7.0, the void returning mbedtls_MODULE* functions
were deprecated in favor of functions returning an int error code. Use
the new function mbedtls_sha256_ret().
Signed-off-by: Russell Senior <russell@personaltelco.net>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This syncs the Orange Pi R1 device tree files with the one from the
upstream kernel and also uses the default configuration from the Orange
Pi Zero.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some functions used by a lot of other software was renamed and is only
active when deprecated functions are allowed, deactivate the removal of
deprecated functions for now.
Fixes: 75c5ab4caf ("mbedtls: update to version 2.7.0")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The PC Engines APU3b has a new nct5104b version with chip ID 0xc453.
This adds support for that version.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
This fixes the following security problems:
* CVE-2018-0488: Risk of remote code execution when truncated HMAC is enabled
* CVE-2018-0487: Risk of remote code execution when verifying RSASSA-PSS signatures
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for GL.iNet GL-B1300
Specification:
- SOC: IPQ4028 / QCA Dakota
- RAM: 256 MiB
- FLASH: 32 MiB
- ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN)
- USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
- WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2
- WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2
- INPUT: one reset and one WPS button
- LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved
- UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1
Installation:
Method 1:
- use serial port to stop uboot
- uboot command: run lf
Method 2:
- push down reset button and power on
- wait until three leds constantly on then release
- upgrade by uboot web at http://192.168.1.1
Note:
- the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method.
- the sysupgrade image can be automatically downloaded if tftp server at
192.168.1.2 have that file.
- the wifi led will be flashing when writing image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
128bc35 logread: fix reconnect logd logic
66347ec logread: move the code setting up the request blob out of the main loop
975a258 logread: move output connection setup code out of main loop
b81bea7 logread: cleanup pid file handling
d73e7d2 ubox: Replace strerror(errno) with %m format.
Signed-off-by: John Crispin <john@phrozen.org>
Some people reported problems with the current development version, so
go back to the latests more or less release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Using PKG_SOURCE_DATE instead of PKG_VERSION will make the build system
generate the version based on the date and the git hash. This way the
tar file name changes when the git hash changes and this avoids problems
when someone forgets to change the version, but changes the git hash.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Changes since last merge into OpenWrt since 2017-12-14:
- Added debugfs file tx_hist.
- Added debugfs file fixed_rate.
- Added debugfs file ba_hist.
- Modified the way to establish BA stream.
- Added code to control BF type.
- Added functions to check/dump dhcp packet.
- Upgrade 88W8964 firmware to 9.3.2.4.
- Added debugfs file coredump.
- Corrected the way to transmit multicast packets.
- Change driver version to 10.3.4.0-20180118.
- Corrected the way to get qos control.
- Assigned broadcast dhcpoffer to another queue.
- Separated broadcast and multicast packets. Bump to latest commit 20180206
Signed-off-by: Chris Breuer <github@chrisbreuer.de>
Make it easily possible to add a custom script in front of this hotplug
script which adds new devices. This is needed for the mvebu target in
which we want to migrate the old configuration before new devices are
getting detected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
D-Link DAP-1522 is a wireless bridge/access point with 4 LAN
ports and a dual-band wireless chipset.
Specifications:
- Ralink RT2880
- 32 MB of RAM
- 4 MB of Flash
- 4x 10/100/1000 Mbps Ethernet (RTL8366SR)
- 802.11abgn (RT2850)
Flash Instructions:
1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin
2. Open the web interface and upload the image
Signed-off-by: George Hopkins <george-hopkins@null.net>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
uqmi contains a command for directly querying the modem if there
is a valid data connection, so let's use it.
This avoids the cases were all previous tests are succesful, but the
actual data link is not up for some reasons, leading to states were we
thought the link was up when it actually wasn't ..
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Originally, the implementation only checked if uqmi command
execution succeeded properly without actually checking it's returned data.
This lead to a pass, even when the returned data was indicating an error.
Rework the verification to actually check the returned data,
which can only be correct if the uqmi command itself also executed correctly.
On command execution success, value "pdh_" is a pure numeric value.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Debugging shows that using the general method properly cleans on each
run, while the method specifying the client-ID shows "No effect"
even while in connected state.
Fixes several connectivity issues seen on specific modems.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This prevents passing down the HOSTCC stuff set in u-boot.mk
which results in linking errors against openssl:
tools/mxsimage.o: In function `sb_aes_reinit':
mxsimage.c:(.text+0x202): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_generate':
mxsimage.c:(.text+0x110d): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x114f): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x11c3): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x1323): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x134a): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_verify_print_header':
mxsimage.c:(.text+0x23ce): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x242c): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x246b): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x24ef): undefined reference to `EVP_CIPHER_CTX_reset'
mxsimage.c:(.text+0x2e52): undefined reference to `EVP_MD_CTX_free'
collect2: error: ld returned 1 exit status
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
It is currently possible to enable connlabel-support in iptables.
However, in order for connlabel to work properly, the kernel module must
also be present. This patch adds support for building the
connlabel-module, and selects it by default when connlabel-support is
enabled.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb firmwares now use ubifs
rootfs. So u-boot env should be set accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated ppfe firmware to NXP LSDK1712 release. Used
ppfe firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NXP LSDK1712 release used two rcw git trees. The
original rcw git tree was still source code but
dropping ls1012a/ls1088a/ls2088a boards in LSDK1712.
Instead another new rcw git tree was used to just
provided rcw binaries for these boards dropped. So
this patch is to update ls-rcw to LSDK1712 release
and add a new ls-rcw-bin package.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
fman-ucode had been migrated from qoriq-open-source
github to NXP github. So the Makefile should be fixed
accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Updated MC firmware to NXP LSDK1712 release. Used
MC firmware git tree on NXP github since it was
migrated here from qoriq-open-source github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
For hardware that supports multiple h/w output queues, add
a compatible scheduler (NET_SCH_MULTIQ).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Current code and also before commit da52dd0c83 was vulnerable to shell
injection using volume lables in the GPT partition table of block
devices. Given that partition names can be freely defined in GPT tables
we really shouldn't evaluate a string which is potentially crafted with
evil intentions. Hence rather use `export -n` to absorb the uevent's
variables into the environment.
Fixes commit da52dd0c83 (base-files: quote values when evaluating uevent)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[mschiffer@universe-factory.net: suggested export -n usage]
The kmod-lp package included both lp.ko and ppdev.ko, but ECP device
drivers may or may not require lp NOT to be loaded, needing only ppdev.
Additionally, There were no packages for any parport interface modules,
such as uss720 or parport_pc, provided here. It has not been otherwise
possible to use PC-style parport hardware for kmod-lp.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
The last_rx field was removed from net_device. Since the field wasn't
used by the generic subsystem, and the driver only writes to it, just
remove the usage.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
When sourcing /sys/class/block/*/uevent values have to be quoted as
they may contain spaces (e.g. in PARTNAME).
Fix this by pre-processing with sed before sourcing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* introduces the BDFs for the OpenMesh A42 in
/lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin.
* adds new firmware firmware-6.bin_RM.4.4.1.c1-00037-QCARMSWP-1 for
QCA6174 hw3.0
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
With no warning, it just looks like the box has hung during boot.
We don't want users resetting it without having captured a crashdump.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Compiling the Intel microcode package results in a
microcode.bin and a microcode-64.bin. As we can
decide based on the subtarget which should be used,
we'll only split the required .bin file with
iucode-tool.
x64 will get the intel-microcode-64.bin
All other variants will get intel-microcode.bin
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the Debian repository for sourcing the ucode files.
Current (20171205) includes support for fam17h CPUs already.
The microcodes will be updated from preinit via a common
script - that's the earliest place where we can do it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add tool to "compile" Intel microcode files. The tool will be
compiled for host (to split the microcode.dat) and for target
(to forcibly reload the microcode if required).
Instead of using the large microcode.bin/microcode-64.bin, the
splitted ucode files (separate for CPU families) will be
installed.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
When we provide the HOSTCFLAGS to the U-Boot build it will fail because
it can not find the u-boot provided header files any more.
Just overwrite and not append the package specific configuration on top
of the configuration provided by u-boot.mk.
uboot-fritz4040 is based on U-Boot 2012.07 and this problem is probably
similar to the problem seen with the lantiq and ar71xx u-boot build.
Fixes: df9781a420 ("u-boot,at91bootstrap: fix incorrect HOSTCPPFLAGS variable")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Once installed fou kernel module allows you to use FOU (Foo over UDP)
and GUE (Generic UDP encapsulation) tunnel protocols.
To get ip fou command working you also need to install ip-full.
Signed-off-by: Filip Moc <lede@moc6.cz>
Since I have no openssl-dev on my machine, I first
get this error:
```
tools/kwbimage.c:21:10: fatal error: openssl/bn.h: No such file or directory
#include <openssl/bn.h>
```
After removing the UBOOT_MAKE_FLAGS the next error is:
```
tools/kwbimage.c:40:6: error: conflicting types for ‘EVP_MD_CTX_cleanup’
void EVP_MD_CTX_cleanup(EVP_MD_CTX *ctx)
```
After removing the OpenSSL patches the next error is:
```
HOSTLD tools/dumpimage
/usr/bin/ld: cannot find -lssl
/usr/bin/ld: cannot find -lcrypto
collect2: error: ld returned 1 exit status
scripts/Makefile.host:108: recipe for target 'tools/dumpimage' failed
make[5]: *** [tools/dumpimage] Error 1
```
So, the final part is to add the build system's
HOST_LDFLAGS to the UBOOT_MAKE_FLAGS.
(which was done in the previous commit)
Then the image builds.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This would should up as `$$(HOSTCPPFLAGS)` in the host CFLAGS.
```
make --jobserver-fds=3,4 -j -C <openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/u-boot-A10-OLinuXino-Lime/u-boot-2017.07 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="<openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/linux-sunxi_cortexa8/linux-4.9.76/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS='-O2 -I<openwrt>/staging_dir/host/include -I<openwrt>/staging_dir/host/usr/include -I<openwrt>/staging_dir/hostpkg/include -I<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/host/include $$(HOSTCPPFLAGS)' HOSTLDFLAGS="" BL31=<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/image/bl31.bin
```
And then it would complain with:
```
/bin/sh: 1: HOSTCPPFLAGS: not found
```
Also, HOSTCPPFLAGS does not exist.
The correct var is HOST_CPPFLAGS.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Activate the support for 64 bit on all 64 bit CPUs and not only x86_64.
ARM64 does not provide an xml file, so do not pack any.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
