Commit graph

36429 commits

Author SHA1 Message Date
Jo-Philipp Wich
81b256ee00 uhttpd: fix handling of special "/" prefix when matching handlers
The special prefix of "/" should match any url by definition but the final
assertion which ensures that the matched prefix ends in '\0' or '/' is causing
matches against the "/" prefix to fail.

Update to current HEAD in order to fix this particular case.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-25 16:38:50 +02:00
Rafał Miłecki
93f9a9c71c kernel: backport MIPS's ioremap_cache from 4.5
It's needed by (updated) bcm47xxsflash driver.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 22:52:44 +02:00
Rafał Miłecki
13e6f7a75d brcm47xx: reorder older entries in image Makefile
Keep all entries sorted and replace tabs with spaces while at it.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 20:35:24 +02:00
Stijn Tintel
839b657a61 kernel: add fix for CVE-2016-5195
Add fix for CVE-2016-5195 to kernel 3.18 and 4.1.
Kernel 4.4 is already fixed since version 4.4.26 which was committed in
32c28a78f7.

Patches taken from Sasha Levin's linux-stable git tree:
http://git.kernel.org/cgit/linux/kernel/git/sashal/linux-stable.git/

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Stijn Tintel
75e63c2494 kernel: update kernel 3.18 to version 3.18.43
Refresh patches for all targets supporting 3.18 and not marked broken.
Compile-tested on all targets using 3.18 and not marked broken.

Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Stijn Tintel
2fc3680dd0 kernel: update kernel 4.1 to version 4.1.34
Refresh patches for all targets supporting 4.1 and not marked broken.
Compile-tested on all targets using 4.1 and not marked broken.

Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Changes to generic/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch based
on a90ee92337.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-24 20:25:14 +03:00
Rafał Miłecki
06405df7a8 brcm47xx: bump kernel to 4.4
Kernel 4.4 was ready for brcm47xx for almost a year now but I kept
postponing the bump due to problems with Linksys WRT300N v1.0. OpenWrt
and LEDE with 4.4 were hanging at the booting with the:
> Starting program at 0x80001000
(the last CFE message).

This was a permanent state, "make distclean" wasn't helping, I spent
hours debugging this and I was reliably reproducing the issue every
time. I also reported it on linux-mips ML in the thread:
> BCM4704 stopped booting with 4.4 (due to vmlinux size?)

After ~month I started working on WRT300N again. I got hangs as expected
every time I switched from 4.1 to 4.4. I started experimenting with:
1) TRX content (I tried dropping rootfs partition)
2) BZ_TEXT_START of lzma-loader
3) Flashing other variants of image: lzma compressed kernel (without a
   loader), gzip compressed one, uncompressed one.

At some point I got rootfs-less image booting and after that I couldn't
reproduce problem anymore, even with a complete firmware. It seems like
hardware was in some locked/unstable state that got magically fixed.

I have LEDE working now, tested it even with "make distclean", it seems
we can bump kernel now. I'll keep testing it on WRT300N for some time.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 17:22:23 +02:00
Rafał Miłecki
6e64a38b00 brcm47xx: build also TRX image for Linksys WRT300N V1
Linksys WRT300N V1 has pretty bugged CFE bootloader (it crashes in a lot
of situations) that doesn't accept .bin image.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 10:34:59 +02:00
Rafał Miłecki
337f219130 brcm47xx: open code Makefile entries for all devices
If we want to use some of new features like per device rootfs we will
need this to specify them there.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-24 10:33:33 +02:00
Felix Fietkau
0ec2738b21 toolchain/gdb: update to version 7.12
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-24 08:45:06 +02:00
Felix Fietkau
ecc091b0f6 binutils: remove old unused versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-24 08:45:06 +02:00
Imre Kaloz
3764caa934 mvebu: add support for the Linksys WRT3200ACM (Rango)
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-24 08:45:06 +02:00
Imre Kaloz
5da412bf80 mwlwifi: upgrade to 10.3.2.0-20161013
Also install the 88W8964 firmware.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
2016-10-24 08:45:06 +02:00
Imre Kaloz
2beab73fad mvebu: add missing status LEDs for Linksys WRT1200AC and WRT1900ACv2
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
2016-10-24 08:45:06 +02:00
Álvaro Fernández Rojas
920f922652 kernel: update kernel 4.4 to version 4.4.27
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2016-10-23 14:56:09 +02:00
Rafał Miłecki
2187f57db6 base-files: add ucidef_set_led_usbport for full usbport support
This helper allows using usbport trigger directly. It requires usbport
compatible syntax and supports specifying multiple USB ports, e.g.:
ucidef_set_led_usbport "usb" "USB" "devicename:colour:function" "usb1-port1" "usb2-port1"

This adds a proper object to the board.json, e.g.
"usb": {
	"name": "USB",
	"type": "usbport",
	"sysfs": "devicename:colour:function",
	"ports": [
		"usb1-port1",
		"usb2-port1"
	]
}
and supports translating it into uci section.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-22 11:16:01 +02:00
Koen Vandeputte
32c28a78f7 kernel: update kernel 4.4 to version 4.4.26
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on cns3xxx & imx6.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-10-21 18:52:28 +03:00
Hannu Nyman
66d604d4a8 busybox: adjust download mirror
* Adjust download locations:
  - use https as busybox.net permanently redirects http to https
  - gentoo mirror has neither 1.25.0 nor 1.25.1 available, so drop it
    in favor of buildroot.net that has 1.25.1

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-21 15:49:01 +03:00
Jo-Philipp Wich
8cc9224115 sdk: predefine SOURCE_DATE_EPOCH
When building packages within the SDK, there is no Git revision history
available so prepopulate SOURCE_DATE_EPOCH in version.mk, similar to
how we handle REVISION already.

Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-10-21 12:43:45 +02:00
Rafał Miłecki
3b26a5bb15 bcm53xx: include b43 in Tenda AC9 image
There is some (poor?) support for BCM43217 in b43.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-20 08:46:26 +02:00
Felix Fietkau
70af3bfd57 libreadline: set ABI_VERSION to force rebuild of dependent packages
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-19 20:26:54 +02:00
Mathias Kresin
3c5a8a2cbc lantiq: enable cpu temp driver for all vr9 boards
Only present on v1.2 vr9 SoCs but the driver takes care to not load on
boards having a v1.1 SoC.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:06 +02:00
Mathias Kresin
23e3314cad lantiq: fix thermal sensors driver
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.

Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.

Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.

Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:06 +02:00
Andreas Eberlein
eba84bee4c lantiq: Sanitize device tree files
The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes.

This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend.

Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
[sanitize all device tree files]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:55:04 +02:00
Andreas Eberlein
72d12672de lantiq: Fix buttons for ARV752DPW
The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.

Both is fixed here.

Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
2016-10-19 19:06:15 +02:00
Mathias Kresin
fa14124616 lantiq: use new build code for DGN3500
Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Mathias Kresin
1f7a03a706 lantiq: drop lzma-loader
It isn't used any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Mathias Kresin
17094e9e64 lantiq: rework VG3503J image
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.

To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:

  VR9 # run reset_uboot_config
  VR9 # reset
  VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The mac address is printed on the label at the bottom of the case.

The following steps are need to be done during first install:

  VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
  VR9 # saveenv
  VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
  VR9 # erase 0xb0020000 $(filesize)
  VR9 # cp.b 0x81000000 0xb0020000 $(filesize)

The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.

Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.

A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-19 19:06:15 +02:00
Felix Fietkau
0c3de24d92 procd: update to the latest version, fixes a few minor service handling issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-19 15:33:41 +02:00
Rafał Miłecki
ea7462ae07 bcm53xx: include usbport trigger for devices with USB
We don't have any code for enabling it automatically yet but it allows
adding entries manually to the /etc/config/system.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:28:52 +02:00
Rafał Miłecki
d0b50c2770 kernel: drop usbdev LED trigger
It was LEDE's trigger that was replaced by upstream usbport one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Rafał Miłecki
0658527e1e switch to the new usbport LED trigger
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-19 12:09:45 +02:00
Ben Greear
1ffb7e47be Latest ath10k CT 988X firmware (beta-18).
*  Backport much of the 10.2 firmware features from upstream QCA driver.
     This includes ANI support, adaptive CCA, tx-hang workarounds,
     and lots of other things.
     Not all of this may be enabled at this point, and more code waits to
     be backported as time and motivation allows.

  *  Fix some rate-control issues where ath10k in station mode (at least), would
     sometimes get stuck at low rates.  This appeared to be a probe related
     state machine issue in the firmware, so I added some timeout logic to kick
     the state machine if it gets stuck.  This signicantly improves throughput
     tests with many stations.

  *  Support configuring WMI WD timeout using SET_SPECIAL API.

  *  Properly configure the rx-mask on bootup to work around problem found
     by Mr. Kazior.  This should remove the need to add the driver hack he
     posted.

  *  Allow configuring pdev failed-retry threshold.  This is how many consecutive
     tx failures the firmware will allow before resetting the wifi chip (not a full
     firmware crash).

Signed-off-by: Ben Greear <greearb@candelatech.com>
2016-10-19 11:13:15 +02:00
Ben Greear
536420647a ath10k-ct: Update to latest 4.7 CT ath10k driver.
Adds Sebastian's 160Mhz support (un-tested), remove DMA32 change that
broke some x86 systems, allow setting 10.1 CT firmware keepalive watchdog
timeout, support QCA 9887 hardware, and some other tweaks.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2016-10-19 11:13:11 +02:00
Rafał Miłecki
81fd64df81 kernel: add package for usbport LED trigger
This is upstream alternative for LEDE's ledtrig-usbdev. It's main
advantages are:
1) Support for assigning more than 1 USB port to the LED
2) Setting proper state when activating with device already connected
3) FWIW it's an upstream driver

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2016-10-18 14:27:14 +02:00
Felix Fietkau
a92f57599c ipq806x: add back end-of-UBI marker for a few factory images (FS#228)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-18 09:30:57 +02:00
Henryk Heisig
f5aa459043 ar71xx: Add support to TP-Link EAP120
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-18 09:18:55 +02:00
Pierre Lebleu
6bb11d52f3 procd: Allow initscripts to start one daemon instance at a time
Signed-off-by: Pierre Lebleu <pierre.lebleu@technicolor.com>
2016-10-18 08:53:38 +02:00
Alberto Bursi
5c96200dab xfsprogs: install path consistent with fs tools
changed install path from /sbin to /usr/sbin to be consistent with other filesystem tools
ext2-3-4 and f2fs tools are in /usr/sbin, for example

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2016-10-18 08:51:46 +02:00
Koen Vandeputte
7f87f82753 kernel: update kernel 4.4 to version 4.4.25
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on cns3xxx & imx6.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2016-10-16 16:27:38 +02:00
Felix Fietkau
b7b223be41 mac80211: backport some upstream a-msdu tx fixes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-17 12:18:25 +02:00
Felix Fietkau
be7f2abb60 iperf: used an updated renamed tarball instead of main upstream URL
iperf upstream added some bugfixes to the already released 2.0.9 version
without changing the filename. This conflicts with old mirrored files
and the hash that we previously used.
To avoid conflict, use a renamed tarball from mirror2.openwrt.org
containing the new upstream changes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-17 11:16:31 +02:00
Felix Fietkau
5f9598a432 mac80211: fix build error in ath10k with hwmon enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2016-10-17 11:01:37 +02:00
Stijn Tintel
39f8e46bb4 busybox: add upstream patch to fix send_to_from
This fixes ntpd when queries are sent to secondary IPv4 IP addresses.
See https://bugs.busybox.net/show_bug.cgi?id=9146

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-15 20:45:10 +03:00
Stijn Tintel
859d30d521 busybox: update to version 1.25.1
Dropped upstream patches:
000-busybox-1.25.0-gzip.patch
000-busybox-1.25.0-ip.patch
000-busybox-1.25.0-ntpd.patch

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2016-10-15 20:45:10 +03:00
Matthias Schiffer
83f7ec31f8
ar71xx: set EU region code for TP-Link TL-WA901ND v4
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.

This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.

Tested-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-15 19:09:56 +02:00
Hauke Mehrtens
7b6fca0e32 procd: update sha256sum
Commit f5c741b5e0 updated procd to a more recent version, but did not
change the hash of the tar. Update it to the one matching the file on
the download servers.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2016-10-15 17:56:23 +02:00
Mathias Kresin
18bb1c9391 ltq-adsl-mei: fix build error
The file to patch doesn't exists. Due to the fact that a src directory
exists, the patch was never applied.

With 28502a9 the behaviour was changed and revealed the issue.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2016-10-15 16:46:42 +02:00
John Crispin
f5c741b5e0 procd: update to latest git HEAD revision
Signed-off-by: John Crispin <john@phrozen.org>
2016-10-15 11:36:53 +02:00
Daniel Engberg
6f5f328003 scripts/freebsd.sh: Remove script
This is outdated and bad practice,  general dependencies should be documented and leave the rest up to the user.

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2016-10-15 11:36:53 +02:00