The Unifi AC-Mesh Pro has identical hardware to the Unifi AC-Pro except
USB support.
Furthermore for setting parameters like antenna gain it is helpful to
know the exact device variant.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
TP-Link Archer C7 v2 USB port LED and GPIO names are in incorrect order,
i.e. in order to match actual user visible labels, usb1 should be usb2,
and vice versa.
This patch swaps LED and GPIO power control node names.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Due do a missing KCONFIG isn't selectable nor enabled in the target
kernel config. Drop it for now and enable/add the driver at the time it
is required.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch ports the TP-Link TL-WR741ND v4 and TL-WR740ND v4 to the
ath79 target.
Because the two devices share the same hw layout, this patch adds a common
.dtsi which is included by the two .dts.
Signed-off-by: Rocco Folino <rocco@folino.io>
The Unifi AC Mesh is equivalent to the Unifi AC Lite. However,
for setting certain parameters with the flashed device it is
helpful that the devices know their variant (e.g. automatically
setting antenna gain for the different antennas in Lite and Mesh).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- fix sysupgrade check
- move usb to v4 dts because v5 doesn't have it
- make wan mac address behave like ar71xx target
- add orange wan led support, it can be userspace activated like:
on:
echo default-on > /sys/class/leds/tp-link\:orange\:wan/trigger
off:
echo none > /sys/class/leds/tp-link\:orange\:wan/trigger
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
rework the dts to a common unifi-ac dtsi
pro network is connected via phy0 and has usb ports
lite network is connected via phy4 without usb ports
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
This target can automatically detect the correct memory size and we've
been using it for long in ar71xx.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the new dynamic partition split in tplink-safeloader so we no longer
have to worry about kernel size increases.
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Netgear WNR612 v2:
- cpu Atheros AR7240 (Python) @400MHz
- flash 4MB
- ram 32MB
- ethernet 10/100: 1xwan + 2xlan (only two)
- radio AR9285
As there is a rebranded WNR612v2 called ON Networks N150R, add
a dtsi which includes all device support, and add a separate dts
for the device only (with a separate one for the subsequent N150R).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add the missing enable and disable function.
Remove dummy mask and unmask function and use the one provided by
irq_dummy_chip.
Allow interrupt status register being defined from dts.
Add ddr_wb_flush for ar934x/qca953x.
Rename controller name to qca,ar9340-intc because this design was
first introduced in AR934x.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
ar71xx/ar913x series use the old pll registers and settings.
However started from ar7242, a new pll register is introduced and the
pll setting is much simpler.
This can be observed from dev-eth.c from the ar71xx target.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
This patch adds dts for qca956x and also support for Phicomm K2T
The qca965x.dtsi adds nearly all the necessary components.
Both ath9k AHB and PCIe worked well.
The Phicomm K2T uses MTD partition 'config' to store the mac addresses in
JSON format. To extract these fields correctly, a script is introduced:
/lib/functions/k2t.sh
This script provides a helper function to extract mac addresses, and is used
in three places.
Hardware spec of Phicomm K2T:
CPU: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337
WiFi 5.8GHz: QCA9886
Flash instruction:
Apply sysupgrade.bin via serial console:
tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
1. Move all status led definitions out of diag.sh into device dt
as we use here a generic script hook.
2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Fixes for WNDR3800 DTS:
* fix bootcmd
* name art partition to reference it for MACs
* format firmware partition's address similarly as others
* make u-boot-env read-only like in ar71xx
* read wan and lan MACs from art
* fix LED and button gpio values to match ar71xx
(orange/green powerLED, reset button)
* enable power LED in dts by alias led-status
* define USB LED triggers and connect to USB port
* change wifi button to KEY_RFKILL like in ar71xx
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Add support for the common led property "linux,default-trigger". It
allows to set a default led trigger via devicetree.
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Readd SoC compatible strings and correct model names mangled in
a51078f735, cleanup dts to remove
duplication, rename dtsi for clarity, use correct GPIO for TL-MR10U
USB power.
Tested only on TL-WR703N due to lack of a TL-MR10U.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
Just name buttons directly, rather than abstract and then also a label.
Likewise for leds. Avoids DTC warnings about unit address with no reg
parameter.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Make the unitname match the reg address. This fixes a DTC warning.
Tested that USB is still functional on an ar9331 device including this
dtsi.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Based on original ar71xx eg200 board files
Tested working:
* usb hub, storage and serial port
* ethernet
* wifi
* leds
* button
sysupgrade from self->self passes validity checks.
sysupgrade from old ar71xx->ath79 passes. (however this doesn't migrate
wireless driver configs)
Only unknown issue is the existance of a /sys/class/leds/ath9k-phy0,
which doesn't "exist"
Signed-off-by: Karl Palsson <karlp@etactica.com>
