Commit graph

313 commits

Author SHA1 Message Date
Luka Perkov
8084b056e2 ar71xx: fix leds and gpio on wpj344
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45589
2015-04-29 20:04:46 +00:00
Luka Perkov
9d76de9771 ar71xx: add support for compex wpj344
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 45527
2015-04-20 20:47:48 +00:00
Felix Fietkau
0a4b20166d ar71xx: Increase RXD/RDV to 2 on OM5P-AN
It was reported that OM5P-AN needs not only a delay setting of 1 for RXD/RDV
but 2. These was found when testing with a NetGear GS752TP POE switch with a
cable length of 50ft and 250ft.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45524
2015-04-20 15:01:00 +00:00
Felix Fietkau
f4e6418a32 ar71xx: add a helper function to set RXDV/RXD of ETH_CFG on AR934x
The ETH_RXDV_DELAY (17:16) and ETH_RXD_DELAY (15:14) are currently not cleared
by the function ath79_setup_ar934x_eth_cfg. Clearing these in the
ath79_setup_ar934x_eth_cfg may cause problems on some hardware because they
rely on the preset value by the bootloader.

Instead another function is introduced which also works on ETH_CFG on AR934x.
It can be used to safely clear and set ETH_RXDV_DELAY and ETH_RXD_DELAY on
machines which require special settings.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45523
2015-04-20 15:00:52 +00:00
Felix Fietkau
5c6925a23b ar71xx: Remove TX/RX delay from pll_1000 for OM5P-AN
The tx/rx delay bits in the ETH_XMII_CONTROL register have to be unset when the
enable_rgmii_rx_delay/enable_rgmii_tx_delay will be set in the AT803x PHY.
Othwise the throughput in gigabit mode is heavily reduced.

Signed-off-by: Sven Eckelmann <sven@open-mesh.org>

SVN-Revision: 45521
2015-04-20 15:00:20 +00:00
John Crispin
efbdc168ff ar71xx: fix ethernet packet loss issues on OM5P-AN
The OM5P-AN boards are suffering from ethernet packet loss when booting with
some active POE setups or when switching to Fast Ethernet when previously
booted with Gigabit ethernet attached.

The cause of the problem is that the AR8035 PHYs requires special register
settings to work reliably on these boards. Enable the RGMII TX, RX delays and
disable SmartEE functionality of the AR8035 PHYs. Also enable the RXD and RDV
delay in the ETH_CFG register to fix the issue.

Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 45438
2015-04-14 19:00:51 +00:00
Gabor Juhos
d0a6b278db ar71xx: add initial support for RB911G-5HPacD
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45299
2015-04-07 20:04:03 +00:00
Gabor Juhos
96b006eb32 ar71xx: routerboot: export extended wlan data via sysfs
Export the data to make it accessible from user-space.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45298
2015-04-07 20:03:43 +00:00
Gabor Juhos
76b5a9aa7d ar71xx: routerboot: add support for extended radio data
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.

Update the RouterBOOT helper code to support the new
format.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45297
2015-04-07 20:03:35 +00:00
John Crispin
17a1e18ee2 ar71xx: add kernel support for the OpenMesh OM5P-AN board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 44861
2015-03-17 09:43:19 +00:00
John Crispin
7ea781558f ar71xx: fix TP-LINK TL-WDR3600/4300 RFKILL switch positions
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44795
2015-03-15 19:39:47 +00:00
John Crispin
5ca2ad1063 Fix (invert/revert) Hornet-UB WPS LED state
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.

The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.

Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>

SVN-Revision: 44791
2015-03-15 19:25:48 +00:00
John Crispin
3a1a4165b8 ar71xx: Ext LNA patch for TUBE2H and HORNET-UB targets
Signed-off-by: Christophe Prévotaux <c.prevotaux@rural-networks.com>

SVN-Revision: 44693
2015-03-12 10:06:53 +00:00
John Crispin
fd82ffec00 ar71xx: Hornet UB GPIO WPS/Reset
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".

There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:

Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.

The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.

Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>

SVN-Revision: 44692
2015-03-12 10:06:42 +00:00
John Crispin
a0c4419b0d ar71xx: improve WD's My Net Wi-fi Range Extender image creation
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.

Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44665
2015-03-11 15:56:34 +00:00
John Crispin
e5373f2761 ar71xx: rename wrt160nl's trx partition parser
This patch renames the partition parser from
wrt160nl to more generic cybertan.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44663
2015-03-11 15:56:15 +00:00
Luka Perkov
e04e623009 ar71xx: wpj588: add missing usb support
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-By: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 44648
2015-03-10 16:11:39 +00:00
John Crispin
4bc9aad079 ar71xx: Fix LED polarity for the TP-LINK TL-MR13U.
Please also backport to Barrier Breaker (this same patch applies there too).

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 44647
2015-03-10 13:26:50 +00:00
Luka Perkov
b065411a85 ar71xx: add support for compex wpj558
OpenWrt can be flashed with following uboot commands:

tftpboot 0x80500000 openwrt-ar71xx-generic-wpj558-16M-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44620
2015-03-06 14:41:57 +00:00
John Crispin
9358a8a798 ar71xx: TL-WA7210n v2 support
This patch adds support for TP-Link TL-WA7210n[0]

[0] http://www.tplink.com/en/products/details/?model=TL-WA7210N

Signed-off-by: Hendrik Frenzel <hfrenzel@scunc.net>

SVN-Revision: 44526
2015-02-24 12:00:50 +00:00
John Crispin
7e4b3de249 ar71xx: add v3.18 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44456
2015-02-15 19:45:29 +00:00
John Crispin
503a1aaaf6 ar71xx: ZyXEL NBG6716 rfkill switch fix
ZyXEL NBG6716 "rfkill" is a switch, not a button.

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44453
2015-02-14 20:48:42 +00:00
John Crispin
235a83cdfe ar71xx: ZyXEL NBG6716 add gpio usb power on/off
ZyXEL NBG6716 add missing GPIO USB power on/off

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44425
2015-02-13 07:28:53 +00:00
John Crispin
de8d6e447c ar71xx: ZyXEL NBG6716 led/buttons cleanup
ZyXEL NBG6716 led/buttons cleanup
 - improper numbered leds
 - improper named buttons

Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>

SVN-Revision: 44417
2015-02-12 08:07:27 +00:00
John Crispin
b523db36a0 ar71xx: dir-505: fix reset button gpio active_low value
Fix 'active_low' default value for the reset button on DIR-505.

Signed-off-by: Rocco Folino <rocco@devzen.net>

SVN-Revision: 44360
2015-02-09 12:17:00 +00:00
John Crispin
a5b60de253 ar71xx: Add support for MERCURY MAC1200R
This patch adds support for MERCURY MAC1200R, a dual band 802.11bgn + 802.11ac
router based on the AR9344, with QCA988x ath10k radio and 5 Fast Ethernet ports

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44359
2015-02-09 12:16:51 +00:00
John Crispin
35d38f21e0 ar71xx: fix nbg6716 power and usb led
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Marcin Mikolajczak <gr4ffy@gmail.com>

SVN-Revision: 44358
2015-02-09 12:16:43 +00:00
Luka Perkov
0067ab8e39 ar71xx: rb2011: apply patch to file
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44314
2015-02-07 21:10:51 +00:00
Luka Perkov
8ca6c1acd4 ar71xx: qihoo: define flash variable as static
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44306
2015-02-07 19:59:02 +00:00
John Crispin
cde2225c7c ar71xx: add support for the TP-LINK TL-WR941ND v5
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44255
2015-02-04 06:10:20 +00:00
John Crispin
baaef42952 ar71xx: Revert "added board support for compex wpj558"
This reverts commit f7873071561d82e75ba2dc46433a2982fef8ac6f.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 44245
2015-02-02 10:32:04 +00:00
John Crispin
bc906ca59e added board support for compex wpj558
Signed-off-by: Christian Mehlis <christian@m3hlis.de>

SVN-Revision: 44237
2015-02-02 09:00:21 +00:00
John Crispin
31fd66f808 ar71xx: add Netgear WNR1000v2/WNR1000v2-VC support (#18633)
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.

Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>

SVN-Revision: 44221
2015-01-30 08:06:40 +00:00
John Crispin
259244624b ar71xx: fix D-Link DIR-615 rev. C1 WLAN MAC address
Fix the WLAN MAC address to match the one printed on the label by using the
correct address from the ART instead of the address of the LAN interface.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 44183
2015-01-28 19:19:47 +00:00
John Crispin
4961c7d0f5 ar71xx: add support for TL-WA701ND v2
Signed-off-by: Luigi Tarenga <luigi.tarenga@gmail.com>

SVN-Revision: 44063
2015-01-20 15:48:07 +00:00
Imre Kaloz
211cac98d5 Belkin AC 1750 DB (F9K1115v2) support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43734
2014-12-17 08:27:38 +00:00
John Crispin
3572657c5a ar71xx: dev-eth: replace mdelay calls
Similar to patch 2. Replace further mdelay calls.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>

SVN-Revision: 43540
2014-12-07 16:53:15 +00:00
Imre Kaloz
974f286261 add D-link DGL-5500 A1 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43401
2014-11-27 14:27:34 +00:00
John Crispin
47ab1cbf23 ar71xx: add support for TP-LINK CPE210/220/510/520
This adds support for the TP-LINK CPE210/220/510/520 (Pharos series). These
devices are very similar to the Ubiquiti NanoStations, but with better specs:
faster CPU, more RAM, 2x2 MIMO.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>

SVN-Revision: 43385
2014-11-26 08:59:32 +00:00
Imre Kaloz
15f6f67d18 Netgear R6100 support
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>

SVN-Revision: 43382
2014-11-26 08:28:22 +00:00
John Crispin
f210f3811a ar71xx: Added support for D-link DHP-1565 rev. A1
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>

SVN-Revision: 43307
2014-11-19 09:20:47 +00:00
John Crispin
6fafcba63b ar71xx: Fix the sys LEDs on the EasyLink M150 and mini
Sets the system LED on the EasyLink M150 and mini to lower-case "easylink"

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43271
2014-11-14 16:58:29 +00:00
John Crispin
bc333d5399 ar71xx: add kernel support for the OpenMesh MR900v2
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43265
2014-11-14 16:54:58 +00:00
John Crispin
95544f33dd ar71xx: add kernel support for the OpenMesh MR900 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 43258
2014-11-14 16:54:07 +00:00
John Crispin
2c72ffc154 ar71xx: add support for Netgear WNR2000v4
Signed-off-by: Michaël Burtin <mburtin@gmail.com>

SVN-Revision: 43173
2014-11-03 20:20:56 +00:00
Felix Fietkau
a1837135e0 ar71xx: add support for buffalo WZR-450HP2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43026
2014-10-22 11:02:18 +00:00
John Crispin
6e46fc8a38 wr1043nd-v2: Change .code of the wi-fi button to KEY_RFKILL
This patch changes the code of the Wi-Fi On/Off button on the TP-Link WR1043ND v2
from KEY_WLAN to KEY_RFKILL (and renames a few constants to match). The reason
for this change is, that the KEY_WIFI button code is not recognized by the
hotplug subsystem. This means that the userspace is not notified about the
button being pressed which effectively renders it useless.

Signed-off-by: Josef Gajdusek <atx@atx.name>

SVN-Revision: 42922
2014-10-14 19:01:21 +00:00
John Crispin
99c238ff15 ar71xx: Fix LED definitions for the DRAGINO2 board
This patch fixes LED definitions for the DRAGINO2 board.

1. It renames the Router/USB led to System, as it is now marked "SYS" on the board.
2. It gives control of the LAN and WAN leds and some other GPIOs to Linux.
3. It fixes the active_low property for the LAN and WAN leds.
4. It sets up WLAN, LAN and WAN leds in the UCI defaults.
5. It allows usage of the System led by the diag.sh script, so it will be used to indicate boot and failsafe status.

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 42897
2014-10-14 10:33:07 +00:00
John Crispin
e2c3c2280c ar71xx: fix reset button gpio for OM2P/OM2P-HS
A typo in the definition for the OM2P reset button disabled its functionality
in OpenWrt. The actual button for these two devices is "1" and not "11".

Signed-off-by: Oren Poleg <oren@poleg.org>
[sven@open-mesh.org: added a commit subject+message]
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 42782
2014-10-06 04:51:51 +00:00
John Crispin
7dbbdfb61f ar71xx: add qihoo 360 c301 router support
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.

This patch adds its initial support.

v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>

SVN-Revision: 42552
2014-09-15 10:19:38 +00:00