Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 38294
The bgmac driver will be used on the brcm47xx and the bcm53xx target.
These are only the patches already applied in current net-next/master
branch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 38288
- remove the kernel+rootfs partitions from the MTD partition map,
- use a temporary directory for intermediate image files,
- append the root squashfs directly to the kernel,
- don't hardcode uImage size in the jffs2 images,
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38194
Fix the image building code so that the kernel correctly
distinguishes between hardware revisions.
Signed-off-by: Mads Hansen <d@taba.se>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38192
This patch adds support for the hardware slide switch on
the TL-MR3040 v2.
Signed-off-by: Mads Hansen <d@taba.se>
[juhosg: use EV_SW instead of EV_KEY]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38190
The Gateworks GW51xx family of products is based on the Freescale
i.MX6DL SoC and offers a small form-factor with peripherals such as:
- i.MX6DL 512MB DDR3
- 256MB NAND FLASH
- 1x PCIe
- 1x USB EHCI (to PCIe socket)
- 1x USB OTG
- HDMI out
- Analog Video in
- Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 38189
The Gateworks GW54xx family of products is based on the Freescale
i.MX6Q SoC and offers a large variety of peripherals such as:
- i.MX6Q 1GB DDR3 (standard)
- 256MB NAND FLASH (standard)
- 6x PCIe (3x with USB)
- Optional expansion for additional USB/PCI based periperhals
- 1x USB EHCI
- 1x USB OTG
- HDMI Audio/Video in/out
- Analog Video in/out
- Analog Audio in/out
- Gateworks System Controller
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 38188
During a reset the gpiolib warns about using the reset gpio
without explicit requesting it before:
[ 147.930000] ------------[ cut here ]------------
[ 147.930000] WARNING: at drivers/gpio/gpiolib.c:103 gpio_ensure_requested+0x68/0xcc()
[ 147.930000] autorequest GPIO-5
[ 147.930000] Modules linked in: ath5k ath mac80211 ipv6 cfg80211 compat arc4 crypto_blkcipher aead gpio_button_hotplug
[ 147.930000] Call Trace:
[ 147.930000] [<8004e3bc>] dump_stack+0x8/0x34
[ 147.930000] [<80058430>] warn_slowpath_common+0x78/0xa4
[ 147.930000] [<800584e4>] warn_slowpath_fmt+0x2c/0x38
[ 147.930000] [<80166f18>] gpio_ensure_requested+0x68/0xcc
[ 147.930000] [<80167264>] gpio_direction_output+0xdc/0x168
[ 147.930000] [<8004aba8>] ar2315_restart+0x28/0x54
[ 147.930000] [<80069778>] sys_reboot+0x178/0x1c0
[ 147.930000] [<80043670>] stack_done+0x20/0x40
[ 147.930000]
[ 147.930000] ---[ end trace 2c7a53d8549562d6 ]---
This is fixed with this patch by using another gpiolib api call
which includes the missing request.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38183
It works:
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r38163)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# uname -a
Linux OpenWrt 3.10.12 #1 Tue Sep 24 18:47:12 CEST 2013 avr32 GNU/Linux
root@OpenWrt:/# cat /proc/cpuinfo
processor : 0
chip type : AT32AP700x revision C
cpu arch : AVR32B revision 1
cpu core : AP7 revision 0
cpu MHz : 140.000
i-cache : 16K (4 ways x 128 sets x 32)
d-cache : 16K (4 ways x 128 sets x 32)
features : dsp simd ocd perfctr java
bogomips : 281.23
root@OpenWrt:/#
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38174
Compile tested only. The target is marked as
broken since 16 months so the kernel version
does not matter too much.
The target is scheduled for removal.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38162
Compile tested only. The target is marked as
broken since 9 months so the kernel version
does not matter too much.
The target is scheduled for removal.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38159
Remove the kernel and rootfs partitions. The Seama
parser can find those automatically:
0x000000070000-0x000000ff0000 : "firmware"
2 seama-fw partitions found on MTD device firmware
0x000000070000-0x0000001b0000 : "kernel"
0x0000001b0000-0x000000ff0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
1 squashfs-split partitions found on MTD device rootfs
0x000000360000-0x000000ff0000 : "rootfs_data"
0x000000ff0000-0x000001000000 : "radiocfg"
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38155
- append the root squashfs directly after the kernel,
- use the 64kraw/128kraw template instead of the 64k/128k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on WZR-HP-G300NH and WZR-600DHP boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38153
The Image/Build/WZRHP64K and the Image/Build/WZRHP128K macros
are similar. Move the common stuff into the Image/Build/WZRHP
macro and update the orignal macros to use that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38152
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a TEW-673GRU board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38151
The Image/Build/DIR825B1 and the Image/Build/DLRTDEV macros
are identical. Merge those into a new Image/Build/CameoAP94
macro, and update the device profiles to use the new macro.
Also rename the dir825b1_* mtdlayout macros to cameo_ap94_*.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38150
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a WispStation M5 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38148
The firmware generation part is the same for both
macros. Move that into a separate macro and use the
new macro for Image/Build/UB{NTXM,DEV}.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38146
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on the WHR-G301N board only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38141
- remove the 'kernel' and 'rootfs' partitions from the mtd layout,
- move the .okli image into the uImage,
- append the root squashfs directly after the kernel,
- use the 64kraw template instead of the 64k
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on the MZK-W300NH board only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38139
- append the root squashfs directly to the kernel,
- use the 64kraw-nojffs template instead of sqashfs-only
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on a TEW-712BR devices only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38130
- append the root squashfs directly to the kernel,
- use the 64kraw/64kraw-nojffs template instead of 64k/squashfs-only,
- ensure, that the signature is placed at the correct offset in
the *-factory images,
- ensure that the generated images have enough erase blocks
for JFFS2 garbage collection,
Tested on DIR-600-A1 and TEW-632BR devices only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38129
The MTD layout of the AP99 based devices is different.
Add new macros to reflect that and use the new macros
for the DIR-615-E4 board.
This prevents overwriting of the 'mac' partition which
contain vital informations. The disadvantage of the change
is that the usable space is reduced by 192KiB. Blame the
vendors for the unfriendly partition layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38128
Also remove the similar code from the Netgear
profile and use the new feature instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38126
- remove the kernel and rootfs partitions from the mtd layout,
the kernel creates those automatically,
- remove estimation step, it is not needed anymore
- put the root squashfs directly after the kernel
- use the 64kraw template
With the default configuration, this allows to use more space for
rootfs_data with 64KiB. Tested on WNDR3700 v1 only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38120
The new macro will be used to determine the firmware
partition size from an MTD layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38117
Enable the wlan2g led in the default configuration of dir-825-c1.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4079/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38106
This patch
- changes the color names from orange to amber
- changes the name of GPIO 13 from WIFI_BGN (wifi_bgn) to WLAN_2G
(wlan2g) to be more consistent with the other routers' files
- changes the descriptions of the hardware keys to be a tad more
explicit
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4081/
[juhosg: update the LED migration script as well]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38105
Enable GPIO 20. This hands off control of the blue planet led to the
integrated switch. Consequently, remove the led configuration for the
blue planet led.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Patchwork: http://patchwork.openwrt.org/patch/4080/
[juhosg: whitespace fixup]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38096
This allows to build images for other boards, even if
the image is too big for Cameo devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38095
This patches fixes the lan led configuration. The new configuration is
identical to the one in mach-db120.c and it works. The previous one
didn't work at all.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38094
The goal is to set the WAN MAC address to the one on the
sticker on the bottom of the unit. Currently it is not
used at all. But some users expect the WAN interface to
have the MAC address that is written on the sticker.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38091
Rename the function and extend it in order to make it
usable from board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 38085
- remove common imx6q-ventana.dtsi - there isn't enough commonality to
warrent this
- rename user led's to 1-based
- add alises used by bootloader
- clean up iomux gpios
- fix pfuze slave address
- enable sata
- add delay after release of pci reset downstream from PCIe switch
- remove PCIe clock configuration as its now handled in updated driver
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 38081
