D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on
module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are
available on castellated pins.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet (all ports available on castellated pins)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11)
- 3x U.FL
- 1x USB 2.0
The dedicated development board includes 5 FE ports, USB 2.0 port, two
buttons (one directly connected to SOC reset input), header with all
GPIOs and several LEDs.
Flash instruction:
Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to
flash OpenWrt firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
- combine support for Oolite/MiniBox V1.0 in single mach-*.c file
- fix model/board names
- include correct/full vendor name
- drop redundant package and factory image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This adds support for AR9331 based Hak5 penetration testing tools:
- WiFi Pineapple NANO
- LAN Turtle
- Packet Squirrel
WiFi Pineapple NANO specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus)
- Ethernet: 1x FE over USB (ASIX AX88772A)
- Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD
- Power: USB 5 V, 1.5 A
- Other: status LED, reset button
LAN Turtle specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B)
- Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot
- Power: USB 5 V, 0.5 A
- Other: status LED, reset button (inside, on PCB)
Packet Squirrel specifications:
- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 2x FE (AR9331)
- Ports: 2x RJ45, 1x USB 2.0
- Power: USB 5 V, 0.12 A
- Other: status LED, reset button, 4-way switch
Flash instructions for all 3 devices:
Original firmware is based on OpenWrt.
Use sysupgrade via SSH to flash.
Signed-off-by: Sebastian Kinne <contact@sebkinne.com>
[squashed commits, combined and reworked mach files, aligned board
naming with general convention, fixed minor issues, tested on real
hardware, reworded commit subject and description]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore T830 is a simple N300 router with 5-port FE switch, detachable
antennas and USB 2.0 port.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531), with ext. PA (SKY65174-21) and LNA
- two external, detachable antennas (RP-SMA)
- 1x USB 2.0
- 8x LED (7 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART and JTAG headers on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to "Advanced" -> "Management" -> "System" and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update "shadow" file and change
hash of root password to something known.
- Repack the archive, rename it back to "bakfile.bin" and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload "sysupgrade" image and install it (only if previous command
succeeded) with command: "sysupgrade -n -F openwrt-...".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344. FCC ID: A3LWAM250.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
fw_setenv bootpart
fw_setenv bootcmd "bootm 0x9f070000"
reboot
Revert to vendor firmware instruction:
1. Download vendor firmware to "/tmp" device and issue below commands:
fw_setenv bootpart 1
sysupgrade -n -F SS_BHUB_v2.2.05.bin
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB
WHQX E600G is based on Qualcomm QCA9531.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB
WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB
Important notice:
First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!
Flash instruction (using U-Boot CLI and tftp server):
1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.
Specification:
720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB
Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.
Short specification:
2x 10/100/1000 Mbps Ethernet, with PoE support
128MB of RAM (DDR2)
16 MB of FLASH
3T3R 2.4 GHz, 802.11b/g/n
2T2R 5 GHz, 802.11ac/n/a, wave 2
built-in 5x 3 dBi antennas
output power (max): 500 mW (27 dBm)
1x RGB LED, 1x button
built-in watchdog chipset
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
This machfile also contains the code for the TL-WR842N/ND v2, which is in
ar71xx-generic and not in ar71xx-tiny.
Fixes: 0cd5e85e7a "ar71xx: create new ar71xx/tiny subtarget for 4MB flash
devices"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add the Embedded Wireless "Balin" platform
SoC: QCA AR9344 or AR9350
RAM: DDR2-RAM 64MBytes
Flash: SPI-NOR 16MBytes
WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
Ethernet: 3 x 10/100 Mb/s
USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
PCI-Express: 1 x lane PCIe 1.2
UART: 1 x Normal, 1 x High-Speed
JTAG: 1 x EJTAG
GPIO: 10 x Input/Output multiplexed
The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB
Flash instruction:
Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.
Specification:
- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.
There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.
This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector
Serial console pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB
Flash instruction:
Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This new subtarget sets the small_flash flag and removes unused kernel
configuration.
small_flash removes KERNEL_KALLSYMS, which saves ~107KB in the default
configuration; removing unneeded hardware support from ar71xx/tiny saves
another ~18KB (both after LZMA).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Rather than including all machines for the generic subtarget in the base
configuration, leave the base configuration without specific machines and
create a proper subtarget config for ar71xx/generic. The configuration
diffs of the mikrotik and nand subtargets get significantly shorter, as
will the configurations of future subtargets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Booting from jffs2 directly is no longer supported, use
rootfstype=squashfs consistently for all subtargets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
