The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC.
http://linux-sunxi.org/MarsBoard_A10
Signed-off-by: Kayo Phoenix <kayo@illumium.org>
[Forward-ported to new target layout:]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Defining it will let the build tool download the tarball file from
a buildbot server, avoiding a clone of the source repo.
Signed-off-by: Arjun AK <lede@arjunak.com>
On NOR based Mikrotik devices, 4K sectors significantly slow down
firmware flashing and jffs2 usage. On NAND based devices they may be
necessary to run rbcfg (the boot loader config is often on SPI NOR).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some targets need 4K sectors for small flash chips (e.g. some
routerboards, where the entire chip is just one "erase block"), whereas
on other devices 4K sectors lead to horrible flash erase/write
performance.
Set the default limit in the generic kernel configuration to 4 MiB to
ensure that all new platforms don't use 4K sectors for bigger flash
chips. On all existing targets use 16 MiB for now to avoid regressions.
They will be changed individually in follow-up commits.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7a49632 logd: use uloop instead of ustream_fd for syslog
69d6542 logd: only create pipe in stream mode
df30c8c logread: terminate after EOF
bdcacad logd: implement oneshot mode for stream log read
4a10d4e logread: use oneshot mode without -f, wait for logd to close
ea3d7fa logd: enforce line length limit for ubus based log messages as well
960a29d logread: remove leftover debug code
a081904 logread: fix line buffer size
2c0d9cf logd: move stripping of newlines to log_add()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This changes the cmdline from:
Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
to
Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5
Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved)
As a consequence booting from the alternative dual-boot partition set
(root=/dev/mmcblk0p8) becomes possible.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Newer devices tend to only support the newer version of the pin
verification command, so also try that one.
Fixes PIN issues with modems like the Sierra Wireless MC7455
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Without this change, when a user disables seccomp support in .config,
procd does not get recompiled unless the package is cleaned manually.
It is because when -D option is missing from cmake command line, cmake
uses cached value from the previous run where seccomp was enabled.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Supported frequencies of all ipq40xx chips are 48, 200, 500 and 716.8 MHz.
Previous 666MHz setting was most likely related to instability of early
chips/boards made before mass production.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
If we enable -fstack-protector while building libunwind, function
__stack_chk_fail_local will be referred to for i386 and powerpc32
arches. This will cause link failure because the default gcc build
specs says no link_ssp if -nostdlib is given.
The error message:
OpenWrt-libtool: link: ccache_cc -shared -fPIC -DPIC .libs/os-linux.o mi/.libs/init.o mi/.libs/flush_cache.o mi/.libs/mempool.o mi/.libs/strerror.o x86/.libs/is_fpreg.o x86/.libs/regname.o x86/.libs/Los-linux.o mi/.libs/backtrace.o mi/.libs/dyn-cancel.o mi/.libs/dyn-info-list.o mi/.libs/dyn-register.o mi/.libs/Ldyn-extract.o mi/.libs/Lfind_dynamic_proc_info.o mi/.libs/Lget_accessors.o mi/.libs/Lget_proc_info_by_ip.o mi/.libs/Lget_proc_name.o mi/.libs/Lput_dynamic_unwind_info.o mi/.libs/Ldestroy_addr_space.o mi/.libs/Lget_reg.o mi/.libs/Lset_reg.o mi/.libs/Lget_fpreg.o mi/.libs/Lset_fpreg.o mi/.libs/Lset_caching_policy.o x86/.libs/Lcreate_addr_space.o x86/.libs/Lget_save_loc.o x86/.libs/Lglobal.o x86/.libs/Linit.o x86/.libs/Linit_local.o x86/.libs/Linit_remote.o x86/.libs/Lget_proc_info.o x86/.libs/Lregs.o x86/.libs/Lresume.o x86/.libs/Lstep.o x86/.libs/getcontext-linux.o -Wl,--whole-archive ./.libs/libunwind-dwarf-local.a ./.libs/libunwind-elf32.a -Wl,--no-whole-archive -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/target-i386_i486_musl-1.1.16/usr/lib -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/target-i386_i486_musl-1.1.16/lib -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/toolchain-i386_i486_gcc-5.4.0_musl-1.1.16/usr/lib -L/var/lib/bbmnt/buildbot/slaves/dave-builder/i386_i486/build/sdk/staging_dir/toolchain-i386_i486_gcc-5.4.0_musl-1.1.16/lib -lc -lgcc -Os -march=i486 -fstack-protector -Wl,-z -Wl,now -Wl,-z -Wl,relro -nostartfiles -nostdlib -Wl,-soname -Wl,libunwind.so.8 -o .libs/libunwind.so.8.0.1
.libs/os-linux.o: In function `_Ux86_get_elf_image':
os-linux.c:(.text+0x588): undefined reference to `__stack_chk_fail_local'
x86/.libs/Lregs.o: In function `_ULx86_access_fpreg':
Lregs.c:(.text+0x25b): undefined reference to `__stack_chk_fail_local'
x86/.libs/Lresume.o: In function `_ULx86_resume':
Lresume.c:(.text+0xdc): undefined reference to `__stack_chk_fail_local'
collect2: error: ld returned 1 exit status
Makefile:2249: recipe for target 'libunwind.la' failed
The snippet from gcc -dumpspecs
%{!nostdlib:%{!nodefaultlibs:%(link_ssp) %(link_gcc_c_sequence)}}
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Update wireguard to latest snapshot:
9fc5daf version: bump snapshot
748ca6b compat: unbreak unloading on kernels 4.6 through 4.9
7be9894 timers: switch to kees' new timer_list functions
6be9a66 wg-quick: save all hooks on save
752e7af version: bump snapshot
2cd9642 wg-quick: fsync the temporary file before renaming
b139499 wg-quick: allow for saving existing interface
582c201 contrib: add reresolve-dns
8e04be1 tools: correct type for CTRL_ATTR_FAMILY_ID
c138276 wg-quick: allow for the hatchet, but not by default
d03f2a0 global: use fewer BUG_ONs
6d681ce timers: guard entire setting in block
4bf32ca curve25519: only enable int128 if compiler support is sound
86e06a3 device: expand scope of destruct lock
e3661ab global: get rid of useless forward declarations
bedc77a device: only take reference if netns is different
7c07e22 wg-quick: remember to rewind DNS settings on failure
2352ec0 wg-quick: allow specifiying multiple hooks
573cb19 qemu: test using four cores
e09ec4d global: style nits
4d3deae qemu: work around ccache bugs
7491cd4 global: infuriating kernel iterator style
78e079c peer: store total number of peers instead of iterating
d4e2752 peer: get rid of peer_for_each magic
6cf12d1 compat: be sure to include header before testing
3ea08d8 qemu: allow for cross compilation
d467551 crypto/avx: make sure we can actually use ymm registers
c786c46 blake2: include headers for macros
328e386 global: accept decent check_patch.pl suggestions
a473592 compat: fix up stat calculation for udp tunnel
9d930f5 stats: more robust accounting
311ca62 selftest: initialize mutex in routingtable selftest
8a9a6d3 netns: use time-based test instead of quantity-based
e480068 netns: use read built-in instead of ncat hack for dmesg
Compile-tested-for: ar71xx
Run-tested-on: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Unset the default LED gpio pin if the same gpio pin is used by a button
defined via platform button. It prevents the change of the GPIO value
on wireless up/down or wireless traffic.
Fixes: FS#1129
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.
Behavior of the LED front after this patch is applied:
cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0 -> white LEDs are OFF
255 -> white LEDs are ON
cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0 -> orange LEDs are OFF
255 -> orange LEDs are ON
If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.
Signed-off-by: Florian Beier <beier.florian@gmail.com>
The GPIOs are used for defined LEDs and therefore are ignored/unset in
the ath9k driver since 192f0a3db8. The wireless led led trigger is
added in userspace since e20965811d, which makes the
ap9x_pci_setup_wmac_led_pin() superfluous.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Upgrade uboot-kirkwood to upstream release 2017.09
Catch up with upstream and move configuration options from
simple defines to Kconfig, as otherwise dependencies would
not be resolved and code would not compile.
Tested-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The platform data was missing the num_registers element which is now
mandatory in linux 4.9
Without this patch, the gpio probing would fail with:
gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines
Fixes: #1106
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr
value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses
are stored in the ART partition and the generated MAC addresses for the
wlan interfaces alternate randomly between 12:34:56:78:90:12 and
00:03:7f:12:34:56.
interface new/ OEM MAC old MAC
wlan-2.4g (phy1): ethaddr undefined
wlan-5g (phy0): ethaddr + 1 undefined
lan : ethaddr + 2 ethaddr
wan : ethaddr + 3 ethaddr + 1
This patch defines stable MAC addresses for the wlan interfaces for
the first time instead of generating them at random. The previously
defined values for lan/ wan are changed to follow the settings of the
OEM firmware.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)
Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile emergency overlay in place.
Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Commit 2e496876c6 fixed the generation of the depends line for external
kernel modules which makes it possible for the build system to
automatically detect this missing dependency.
This fixes the packaging of kmod-ltq-atm for the ar9, xway and
xway-legacy subtarget.
Fixes: FS#1124
Signed-off-by: Mathias Kresin <dev@kresin.me>
Unmodified dns and domain variables could be needed in user script (/etc/udhcpc.user).
Signed-off-by: Tero Jänkä <tero.janka@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> (cleanup)
mpc85xx uses this for firmware image files, since the dtb data is not
directly part of the kernel image. This causes build failures in the
image builder.
Fix this by adding a separate build step that runs this call earlier,
reusing the generated file for any calls from kernel or image build
commands.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add xconfig target to include/toplevel.mk, so that ``make xconfig`` can
be invoked from $TOPDIR to use Qt based configuration tool to prepare
.config file.
The qconf related sources are taken from linux 4.9.13 archive.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
This commit adds qconf related files to .gitignore.
The files to be tracked are qconf.cc, qconf.h, and images.c.
The files to be ignored are qconf*.o, qconf*, qconf.moc, and
.tmp_qtcheck.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
qconf is kconfig UI utilizing QT toolkit. This makes it possible to use
graphical interface interaction to configure LEDE build target.
This commit adds qconf target to ./script/config/Makefile to be used by
toplevel ``make xconfig`` later.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
On some devices the flash chip needs to be in 3-byte addressing mode during
reboot, otherwise the boot loader will fail to start.
This mode however does not allow regular reads/writes onto the upper 16M
half. W25Q256 has separate read commands for reading from >16M, however
it does not have any separate write commands.
This patch changes the code to leave the chip in 3-byte mode most of the
time and only switch during erase/write cycles that go to >16M
addresses.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
