Commit graph

1581 commits

Author SHA1 Message Date
Robert Marko
b834487203 ar71xx: add support for TP-Link TL-WR940N v6
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.

Installation: flash factory image through WEB UI or use TFTP.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-04-06 23:11:00 +02:00
Peng Zhang
bbc2e1d919 ar71xx: change brand name WHQX to Qxwlan
Signed-off-by: Peng Zhang <sd20@qxwlan.com>
2018-04-06 23:11:00 +02:00
Nicolò Veronese
d265a8f2ca
ar71xx: Add support for D-Link DAP-1330 a1
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)

Flash instruction: use "factory" image directly in vendor GUI.

This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.

You can access vendor firmware over serial using:
- login: root
- password: linuxrocks

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2018-04-05 15:28:56 +02:00
Reto Schneider
58fe527931 ar71xx: Fix typo in wan LED color of gl-mifi
It was wrong from the beginning and the trigger for the wan led was
never set due to the typo.

Signed-off-by: Reto Schneider <code@reto-schneider.ch>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-04 09:27:18 +02:00
Arne Zachlod
d0988235dd
ar71xx: add support for Ubiquiti Litebeam M5
Specification:
- SoC: Atheros AR9342
- Flash: 8 MiB
- RAM: 64 MiB
- UART: 1x UART on PCB - 115200 8N1
- Ethernet: 1 x 100 Mbit with passive PoE (24V/0.2A)

Doesn't work:
* Flash via TFTP with Ubiquiti Uboot

Installation via vendor firmware:
- upload factory image via webinterface

Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2018-03-15 19:11:39 +01:00
Felix Fietkau
83ddc3bfc2 ar71xx: fix mii bus irq assignment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-04 19:37:20 +01:00
Felix Fietkau
f62d2b9549 ar71xx: remove pdata->fifo_cfg*
The values are the same for all chipsets that use it

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-03-04 19:37:20 +01:00
Felix Fietkau
36fb0697e2 ar71xx: fix build with ag71xx debugfs support enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-28 13:57:58 +01:00
Rosen Penev
810659a22c ag71xx: Move timestamp struct member outside of struct.
With this change, the timestamp variable is only used in ag71xx_check_dma_stuck. Small tx speedup.

Based on a Qualcomm commit. ag->timestamp = jiffies was not replaced with netif_trans_update(dev) because of this quote:

It should be noted that after this series several instances
of netif_trans_update() are useless (if they occur in
.ndo_start_xmit and driver doesn't set LLTX flag -- stack already
did an update).

From: http://lists.openwall.net/netdev/2016/05/03/87

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-28 12:46:02 +01:00
Piotr Dymacz
8c64824576 ar71xx: add support for GainStrong Oolite V5.2
GainStrong Oolite V5.2 is a small (39.5 x 78 mm), dual-band system on
module, based on Qualcomm QCA9531 + QCA9887. All QCA9531 SOC GPIOs are
available on castellated pins.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet (all ports available on castellated pins)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887) with ext. FEM (SKY85710-11)
- 3x U.FL
- 1x USB 2.0

The dedicated development board includes 5 FE ports, USB 2.0 port, two
buttons (one directly connected to SOC reset input), header with all
GPIOs and several LEDs.

Flash instruction:

Vendor firmware is based on OpenWrt. LuCI or sysupgrade can be used to
flash OpenWrt firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
907d674910 ar71xx: rework GainStrong devices support
- combine support for Oolite/MiniBox V1.0 in single mach-*.c file
- fix model/board names
- include correct/full vendor name
- drop redundant package and factory image

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Sebastian Kinne
950b278c81 ar71xx: add support for AR9331 based Hak5 devices
This adds support for AR9331 based Hak5 penetration testing tools:

- WiFi Pineapple NANO
- LAN Turtle
- Packet Squirrel

WiFi Pineapple NANO specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: 1T1R AR9331 (built-in), 1T1R AR9271 (built-in via USB bus)
- Ethernet: 1x FE over USB (ASIX AX88772A)
- Ports: 2x RP-SMA for antennas, 1x USB 2.0 (host), 1x micro SD
- Power: USB 5 V, 1.5 A
- Other: status LED, reset button

LAN Turtle specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 1x FE (AR9331), 1x FE over USB (Realtek RTL8152B)
- Ports: 1x RJ45, version dependent: micro SD or 3G SIM slot
- Power: USB 5 V, 0.5 A
- Other: status LED, reset button (inside, on PCB)

Packet Squirrel specifications:

- SoC: Atheros AR9331 (400 MHz)
- RAM: 64 MB (DDR2)
- FLASH: 16 MB
- WiFi: none
- Ethernet: 2x FE (AR9331)
- Ports: 2x RJ45, 1x USB 2.0
- Power: USB 5 V, 0.12 A
- Other: status LED, reset button, 4-way switch

Flash instructions for all 3 devices:

Original firmware is based on OpenWrt.
Use sysupgrade via SSH to flash.

Signed-off-by: Sebastian Kinne <contact@sebkinne.com>
[squashed commits, combined and reworked mach files, aligned board
naming with general convention, fixed minor issues, tested on real
hardware, reworded commit subject and description]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
22ae9b742b ar71xx: YunCore AP90Q image supports also AP80Q
Vendor released new model (AP80Q) which is identical from hardware point
of view with already supported AP90Q. Include AP80Q in machine name.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
d6f187f938 ar71xx: add support for YunCore T830
YunCore T830 is a simple N300 router with 5-port FE switch, detachable
antennas and USB 2.0 port.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531), with ext. PA (SKY65174-21) and LNA
- two external, detachable antennas (RP-SMA)
- 1x USB 2.0
- 8x LED (7 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART and JTAG headers on PCB

Flash instruction:

1. First, gain root access to the device, following below steps:

- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to "Advanced" -> "Management" -> "System" and download backup of
  configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update "shadow" file and change
  hash of root password to something known.
- Repack the archive, rename it back to "bakfile.bin" and use to
  restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.

2. Then, install OpenWrt:

- Login over SSH and issue command:
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload "sysupgrade" image and install it (only if previous command
  succeeded) with command: "sysupgrade -n -F openwrt-...".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
e58e49bdbe ar71xx: add support for Samsung WAM250
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344. FCC ID: A3LWAM250.

Specification:

- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz (AR9344), with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)

Flash instruction:

This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.

You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).

1. Make sure that your device uses second (bootpart=2) image using
   command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
   latest vendor firmware (after the update, device should boot from
   second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
   wget, tftp or ftpget) to "/tmp" and issue below commands:

   mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
   mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
   fw_setenv bootpart
   fw_setenv bootcmd "bootm 0x9f070000"
   reboot

Revert to vendor firmware instruction:

1. Download vendor firmware to "/tmp" device and issue below commands:

   fw_setenv bootpart 1
   sysupgrade -n -F SS_BHUB_v2.2.05.bin

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
1b0e7a1453 ar71xx: fix COMFAST CF-E375AC support
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
650a5e993b ar71xx: add support for COMFAST CF-E385AC
COMFAST CF-E385AC is an AC2200 ceiling mount AP with PoE support, based
on Qualcomm/Atheros QCA9558 + QCA9984 + QCA8337N.

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 256 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet, with PoE support
- 3T3R 2.4 GHz (QCA9558), with external LNA and PA (SE2576L)
- 4T4R 5 GHz (QCA9984), with external FEM (SKY85728-11)
- 7x internal antennas
- 1x RGB LED (driven by GPIO)
- 1x button (reset)
- UART, LEDs/GPIO and USB headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
106a56238f ar71xx: rename COMFAST CF-E355AC to CF-E355AC v1
There are now supported two versions of the CF-E355AC board which differ
in 802.11ac radio chip. Include version number in board, model, image
filename, etc., also for the v1.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Ding Tengfei
e07014e70b ar71xx: add support for COMFAST CF-E355AC v2
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9886.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[updated kernel config for both boards]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Peng Zhang
d8e6c3f6d9 ar71xx: add support for WHQX E1700AC/E600G/E600GAC v2
WHQX E1700AC v2 is based on Qualcomm QCA9563 + QCA9880 + QCA8334.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz (QCA9563) with external FEM (SKY85309-11)
- 3T3R 5 GHz (QCA9880) with external FEM (SKY85728-11)
- 2x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 1x USB 2.0
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (J5) and LEDs (J13) headers on PCB

WHQX E600G is based on Qualcomm QCA9531.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531) with external PA (LXK-6601)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J100), SIM (J34), JTAG (J5) and LEDs (J7) headers on PCB

WHQX E600GAC is based on Qualcomm QCA9531 + QCA9887.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 64/128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887) with external FEM (SKY85703-11)
- 2x 10/100 Mbps Ethernet
- 6x LED (1x RGB, 5 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-12 V)
- UART (J100), USB (J102), JTAG (J5) and LEDs (J7) header on PCB

Important notice:

First version of these boards are using different mtd layout, with ART
data at the end. You should not use v2 images on v1 board because it
will result in lost of ART data!

Flash instruction (using U-Boot CLI and tftp server):

1. Configure PC with static IP 192.168.1.10 and tftp server.
2. Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
3. Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
4. Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

1. Configure PC with static IP 192.168.1.xxx(2-254)/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
3. Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: Peng Zhang <sd20@qxwlan.com>
[reworked: image generation code, mach-* files, commit description,
fixed minor code style issues, rebased on master]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Piotr Dymacz
fc43e7a6e0 ar71xx: fix typos and indentation in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok
bb1df2d75b ar71xx: include vendor name for GL iNet products
This patch include GL.iNet vendor name in the
machine name for GL.iNet vendor products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:22 +01:00
Kyson Lok
9dbfd8e9df ar71xx: uniform GL iNet products mach name
The mach name of GL AR150 and GL AR300 is inconsistent
with other products.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
2018-02-22 18:53:21 +01:00
Julien Dusser
8dd455e3c4 ar71xx: add more registers to ar71x_regs.h
Add more registers and flags to ar71x_regs.h for QCA955x and QCA956x
SoCs. Values come from Qualcomm Atheros u-boot code.

Patches can be merged into
622-MIPS-ath79-add-more-register-defines-for-QCA956x-SoC.patch

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
2018-02-13 11:20:58 +01:00
Karl Palsson
b2a5f7683b ar71xx: Add eTactica EG-200 support
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.

Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.

Flash instruction:
    Original firmware is based on OpenWrt.
    Use sysupgrade image directly in vendor GUI.

Signed-off-by: Karl Palsson <karlp@etactica.com>
2018-02-13 10:01:53 +01:00
Henryk Heisig
a338491a30 ar71xx: add support for TP-Link RE355
This device is identical as TP-Link RE450
RE355 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9558+QCA9880.

Specification:

720/600/200 MHz (CPU/DDR/AHB)
64/128 MB of RAM (DDR2)
8 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
1x 10/100/1000 Mbps Ethernet
7x LED, 3x button
UART header on PCB

Flash instruction:
Web:
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin
and use OEM System Tools - Firmware Upgrade site.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2018-02-13 09:21:20 +01:00
Ding Tengfei
bf66bb8c96 ar71xx:add support for COMFAST CF-E375AC
COMFAST CF-E375AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.

Short specification:

    2x 10/100/1000 Mbps Ethernet, with PoE support
    128MB of RAM (DDR2)
    16 MB of FLASH
    3T3R 2.4 GHz, 802.11b/g/n
    2T2R 5 GHz, 802.11ac/n/a, wave 2
    built-in 5x 3 dBi antennas
    output power (max): 500 mW (27 dBm)
    1x RGB LED, 1x button
    built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
2018-02-11 16:20:24 +01:00
Felix Fietkau
798497c66e ar71xx: use global timestamp for hang check
Shrink the size of struct ag71xx_buf to 8 bytes, which improves cache
footprint

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Felix Fietkau
31e6016d2e ar71xx: only access device stats in tx handler if packets were processed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Felix Fietkau
890e7458b0 ar71xx: allocate rx/tx descriptor/buffers in one chunk
Reduces false sharing due to cache aliases

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:16:25 +01:00
Rosen Penev
4e03a742e0 ag71xx: Reorder ag71xx struct members for better cache performance
Qualcomm claims this improves the D-cache footprint. Origina commit message below:

From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Fri, 7 Jun 2013 10:57:28 -0500
Subject: [ag71xx] cluster/align structs for cache perf

Cluster the frequently used, per-packet structures in ag71xx near
to each other, and cacheline-align them.  Some other re-ordering
occurred to move "warmer" structures near the per-packet structures.

Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-02-05 10:16:25 +01:00
Catrinel Catrinescu
4ba2dd130a ar71xx: add ew-balin platform from Embedded Wireless
Add the Embedded Wireless "Balin" platform
 SoC: QCA AR9344 or AR9350
 RAM: DDR2-RAM 64MBytes
 Flash: SPI-NOR 16MBytes
 WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n
 Ethernet: 3 x 10/100 Mb/s
 USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up
 PCI-Express: 1 x lane PCIe 1.2
 UART: 1 x Normal, 1 x High-Speed
 JTAG: 1 x EJTAG
 GPIO: 10 x Input/Output multiplexed

The module comes already with the current vanilla OpenWrt firmware.
To update, use "sysupgrade" image directly in vendor firmware.

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
2018-01-25 16:50:08 +01:00
Gabor Juhos
eb9e3651dd ar71xx: add support for the MikroTik RB911-2Hn/5Hn boards
The patch adds support for the MikroTik RB911-2Hn (911 Lite2)
and the RB911-5Hn (911 Lite5) boards:

  https://mikrotik.com/product/RB911-2Hn
  https://mikrotik.com/product/RB911-5Hn

The two boards are using the same hardware design, the only difference
between the two is the supported wireless band.

Specifications:
  * SoC: Atheros AR9344 (600MHz)
  * RAM: 64MiB
  * Storage: 16 MiB SPI NOR flash
  * Ethernet: 1x100M (Passive PoE in)
  * Wireless: AR9344 built-in wireless MAC, single chain
              802.11b/g/n (911-2Hn) or 802.11a/g/n (911-5Hn)

Notes:
  * Older versions of these boards might be equipped with a NAND
    flash chip instead of the SPI NOR device. Those boards are not
    supported (yet).
  * The MikroTik RB911-5HnD (911 Lite5 Dual) board also uses the
    same hardware. Support for that can be added later with little
    effort probably.

Installation:

1. Setup a DHCP/BOOTP Server with the following parameters:
   * DHCP-Option 66 (TFTP server name): pointing to a local TFTP
     server within the same subnet of the DHCP range
   * DHCP-Option 67 (Bootfile-Name): matching the initramfs filename
     of the to be booted image. The usable intramfs files are:
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf
       - openwrt-ar71xx-mikrotik-vmlinux-initramfs-lzma.elf
       - openwrt-ar71xx-mikrotik-rb-nor-flash-16M-initramfs-kernel.bin

2. Press the reset button on the board and keep that pressed.

3. Connect the board to your local network via its ethernet port.

4. Release the button after the LEDs on the board are turned off.
   Now the board should load and start the initramfs image from
   the TFTP server.

5. Upload the sysupgrade image to the board with scp:
     $ scp openwrt-ar71xx-mikrotik-rb-nor-flash-16M-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/fw.bin

5. Log in to the running system listening on 192.168.1.1 via ssh
   as root (without password):
     $ ssh root@192.168.1.1

7. Flash the uploaded firmware file from the ssh session via the
   sysupgrade command:
     root@OpenWrt:~# sysupgrade /tmp/fw.bin

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:45 +01:00
Gabor Juhos
e379e60b17 ar71xx: mach-rbspi: return rb_info from rbspi_platform_setup
Modify the rbspi_platform_setup() function to return the pointer of the
rb_info structure. This allows board specific setup routines to access
the various fields of the information. It is useful for investigating
the hardware option bits for example.

Also update the board setup codes, to ensure that those handle the new
return value correctly.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:16 +01:00
Gabor Juhos
c7371cd1ee ar71xx: add definitions for RouterBOARD hardware option bits
Add bit definitions for the 'hardware options' tag which is used in
the MikroTik devices' hardware configurations. These values can be
used in board setup codes, to do different initialization sequences.
The values were obtained from the RouterOS 6.41-rc38 patches.

Additionally, introduce two helper functions what make the processing
of the hardware options easy.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-22 10:53:00 +01:00
Gabor Juhos
ec4e9a88ff ar71xx: drop mdio-gpio.h include from mach-om5pacv2.c
The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.

Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.

Compile tested only.

Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Gabor Juhos
bc178f6b15 ar71xx: mach-rbspi: simplify reset button registration
The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.

Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-17 11:07:17 +01:00
Roger Pueyo Centelles
e15c63a375 ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)
This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9556
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
 - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
   PoE in

Working:
 - Board/system detection
 - Sysupgrade
 - Serial console
 - Ethernet
 - 2.4 GHz radio
 - 5 GHz radio
 - Reset button

Not working:
 - LEDs (added according to Mikrotik's GPL sources but not functional)

 Unsupported:
 - ZT2046Q SPI temperature and voltage sensor

Contributors: Giuseppe Tipaldi (@Ciusss89)
              Ricky (@rickydee)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
2018-01-15 04:14:18 +01:00
Piotr Dymacz
2e5252d346 ar71xx: add support for GL.iNet GL-AR750
GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Davide Fioravanti
a85db951db ar71xx: fix Sitecom WLR-8100 support
This patch fixes Sitecom WLR-8100:

- mtd layout
- LAN and WAN MAC address setup
- 2.4 GHz Wi-Fi MAC address setup
- 5 GHz Wi-Fi support (calibration data, MAC address setup, missing
  ath10k-* packages)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[squashed commits, fixed whitespace issues, reworded commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
af8f0629df ar71xx: add support for ALFA Network R36A
ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:12:13 +01:00
Piotr Dymacz
1f06144cde ar71xx: add support for Teltonika RUT900
Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.

There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.

This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector

Serial console pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-15 00:09:43 +01:00
Piotr Dymacz
4b0eebe9df ar71xx: add support for ALFA Network N5Q
ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
   device, wait for first blink of all LEDs (indicates network setup),
   then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 21:30:16 +01:00
Piotr Dymacz
7f9f42d42e ar71xx: add support for ALFA Network AP91-5G
ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB

Flash instruction:

Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-01-14 20:33:18 +01:00
Gabor Juhos
82cc439976 ar71xx: remove obsolete '< KERNEL_VERSION(4, 4, 0)' check
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.4.0 is always
false. Remove the obsolete check from mach-rb4xx.c to clean up the code
a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:19 +01:00
Gabor Juhos
8f44c8086b ar71xx: remove obsolete '< KERNEL_VERSION(4, 2, 0)' check
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 4.2.0 is always
false. Remove the obsolete check from ag71xx_main.c to clean up the code
a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:18 +01:00
Gabor Juhos
7a4930b27c ar71xx: remove obsolete '< KERNEL_VERSION(3, 15, 0)' checks
Because the oldest supported kernel version on the ar71xx target is 4.4,
the condition that the kernel version is smaller than 3.15.0 is always
false. Remove the obsolete checks from the target specific source files
to clean up the code a bit.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2018-01-09 21:33:18 +01:00
Vittorio Gambaletta
d40a358136
ag71xx: Fix rx ring buffer stall on small packets flood on qca956x and qca953x.
Backported from Code Aurora QSDK

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
2017-12-29 15:17:07 +01:00
Gabor Juhos
6456999731 ar71xx: spi-rb4xx: balance clk_prepare_enable() call
Commit c312cef223 ("ar71xx: spi-rb4xx fix.") replaced the clk_enable() call
with clk_prepare_enable() to meet the common clock framework requirements.
However it did not change the clk_disable() call in the error patch which
thus leads to imbalance.

Fix the code by using the correct counterpart of clk_prepare_enable() in both
places.

Fixes: c312cef223 ("ar71xx: spi-rb4xx fix.")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2017-12-24 09:03:01 +01:00
Roger Pueyo Centelles
82626cc145 ar71xx: add support for MikroTik RouterBOARD 921GS-5HPacD r2 (mANTBox 15s)
This patch adds support for the MikroTik RouterBOARD 921GS-5HPacD r2
(mANTBox 15s), an outdoor sector antenna with a built-in 802.11ac
wireless router. Additionally, it adds a new profile for devices with
>= 128 MB NAND flash and 802.11ac to the ar71xx/mikrotik subtarget.

See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9558 (720 MHz)
 - RAM: 128 MB
 - Storage: 128 MB NAND
 - Wireless: external QCA9822 802.11a/ac 2x2:2
 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
 - SFP: 1x host

Working:
 - Board/system detection
 - NAND storage detection
 - Wireless
 - Ethernet
 - 1x user LED
 - Reset button
 - Sysupgrade

Untested:
 - SFP cage (probably not working)

Installation:
 - Boot initramfs image via TFTP and then flash sysupgrade image

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2017-12-21 17:06:54 +01:00
Roger Pueyo Centelles
9604f7d337 ar71xx: fix spelling in mach-rb922.c
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2017-12-21 17:06:54 +01:00
Roger Pueyo Centelles
8927446dae ar71xx: fix rb922gs_nand_scan_fixup()
Apply code from commits 9e1bc27e6d
(ar71xx: Fix UBIFS work on Mikrotik RB95x devices) and
665bb27499 (ar71xx: fix invalid pointer
dereference in rb95x_nand_scan_fixup()) to RB92x devices too.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2017-12-21 17:06:54 +01:00
Gabor Juhos
665bb27499 ar71xx: fix invalid pointer dereference in rb95x_nand_scan_fixup()
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
chip->options causes an invalid pointer dereference (FS#1200).

Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.

Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
2017-12-16 00:00:25 +01:00
Gabor Juhos
2ecc413107 ar71xx: fix invalid pointer dereference in c60_nand_scan_fixup()
Since Linux 4.6, mtd->priv no longer points to the NAND specific
structure. Under 4.9 it contains NULL, thus using it to access
the fields of the nand_chip structure causes an invalid pointer
dereference.

Update the code to use the mtd_to_nand() helper under 4.9 to obtain
the address of the chip specific data.

Compile tested only.

Fixes: 7bbf4117c6 ("ar71xx: Add kernel 4.9 support")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
2017-12-15 23:57:41 +01:00
kyson Lok
e776b6ed0b ar71xx: fix LED name typo for GL-AR300M
It shouldn't use double colon characters.

Signed-off-by: kyson Lok <kysonlok@gmail.com>
2017-12-15 23:50:21 +01:00
John Crispin
9f8d28285d Revert "ar71xx: TL-WR1043N v4/v5: add orange WAN LED support"
This reverts commit 256990cbc0.

this commit caused a compile error

"TL_WR1043_V5_GPIO_LED_WANORANGE" is undefined.

Signed-off-by: John Crispin <john@phrozen.org>
2017-12-14 11:00:11 +01:00
Tim Thorpe
256990cbc0 ar71xx: TL-WR1043N v4/v5: add orange WAN LED support
Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and
v5. Minor format correction on a constant for consistency.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
2017-12-14 09:29:31 +01:00
Rosen Penev
1c2fdfbaf2 ag71xx: Reduce NAPI weight to 32.
Qualcomm claims this reduces cache misses. Original commit message below:

From: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Date: Tue, 11 Jun 2013 12:18:46 -0500
Subject: [ag71xx] reduce NAPI weight

In an attempt to increase our cache warmth, we are decreasing NAPI.
This increases the warmth of the reused SKBs.

Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-12-08 19:54:37 +01:00
Rosen Penev
524d103e7e Revert "ag71xx: Switch from driver to kernel macro for NAPI_WEIGHT."
The motivation for this was misguided. It turns out tuning the NAPI weight could be useful for testing purposes. Therefore reverting.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-12-08 19:54:34 +01:00
David Bauer
5a8e9846af
ar71xx: C58/C59 fix LAN1 working incorrectly
This commit fixes LAN Port 1 not transferring data in case no
other LAN Port has active link-state on TP-Link Archer C58/C59.

Signed-off-by: David Bauer <mail@david-bauer.net>
2017-12-08 13:53:03 +01:00
Paul Wassi
e3c55dbe30 ar71xx: merge mach-files for TP-Link TL-WR802N v1 and v2
TP-Link TL-WR802N v1 and v2 are set up with almost same configuration in
the mach-files. Merge the mach-files of these devices.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Tim Thorpe
673793d753 ar71xx: add support for TP-Link TL-WR1043N v5
TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option.

The software is more in line with the Archer series in that it uses a
nested bootloader scheme.

Specifications:

 - QCA9563 at 775 MHz
 - 64 MB RAM
 - 16 MB flash
 - 3 (non-detachable) Antennas / 450 Mbit
 - 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
 - reset and Wi-Fi buttons

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
2017-11-14 22:36:46 +01:00
Paul Wassi
e202a8b9f6 ar71xx: add support for TP-Link TL-WA901ND v5
The TL-WA901ND v5 has the same hardware as v4, although the PCB has
a different layout. Installation from factory is done via TFTP.
(rename -factory image to wa901ndv4_tp_recovery.bin for tftp)

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Robert Marko
ac4a52b5c8 ar71xx: complete support for RB mAP 2nD
This patch adds support for the MikroTik RouterBOARD mAP 2nD
https://mikrotik.com/product/RBmAP2nD

Specifications:

- SoC: Qualcomm QCA9531 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 2x100M (802.3af/at POE in and passive POE out on ETH2)
- USB: microUSB type AB port

This patch adds missing code to fully support mAP. Machfile already
contained configuration for mAP 2nD, but device specific configuration
like LEDs etc., was missing.

Note: The POE LED works but doesn't turn on when POE passthrough is
enabled, despite being configured with GPIO trigger.

Installation

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Robert Marko
3b15eb06c3 ar71xx: complete support for RB wAP 2nD
This patch adds support for the MikroTik RouterBOARD wAP
https://mikrotik.com/product/RBwAP2nD

Specifications:

- SoC: Qualcomm QCA9533 (650 MHz)
- RAM: 64 MB
- Storage: 16 MB NOR SPI flash
- Wireless: built-in QCA9533, 2x2:2
- Ethernet: 1x100M (802.3af/at POE in)

This patch adds missing code to fully support wAP. Machfile already
contained configuration for wAP 2nD but device specific configuration
like LEDs etc. was missing.

Installation:

1. Login to the Mikrotik WebUI to backup your licence keys
2. Setup a DHCP/BOOTP server with:
   - DHCP-Option 66 (TFTP server name) pointing to a local TFTP
     server within the same subnet of the DHCP range
   - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
     of the to be booted image
3. Connect the port labeled internet to your local network
4. Keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
server. Login as root/without password to the started LEDE via SSH
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
- rbcfg set boot_protocol bootp
- rbcfg set boot_device ethnand
- rbcfg apply

Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-14 22:36:46 +01:00
Paul Wassi
b23b0fb28b ar71xx: add support for TP-Link TL-WR810N v2
TP-Link TL-WR810N v2 is a compact Wi-Fi router with two Ethernet ports.

Specification:

- QCA9533 (650 MHz)
- 32 MB RAM
- 8 MB Flash
- 300 Mbps Wi-Fi 2.4 GHz
- 2x 10/100 Mbps Ethernet (eth0, eth1)
- UART on testpads on PCB
- 1x LED (GPIO-controlled)
- 1x reset/WPS button
- 1x slide-switch with 2 GPIO inputs

Flash instructions:

- Flash as regular firmware update in Web UI
- Default: 192.168.0.254 / admin / admin
- Select *-factory.bin

When holding reset button during power-up, U-Boot requests a file
'wr810nv1_tp_recovery.bin' from TFTP server at 192.168.0.66

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
c83bdd094e ar71xx: add support for Wallys DR342
Wallys DR342 is a 5 GHz, 2T2R AP/CPE board based on Atheros AR9342.

Short specification:

- 560/450/225 MHz (CPU/DDR/AHB)
- 1x Gbps Ethernet (AR8035) with passive PoE support (24-56 V)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 5 GHz with external FEM (SKY85728-11), up to 30 dBm
- 2x MMCX connectors
- miniPCIe connector with PCIe and USB 2.0 buses
- optional miniSIM slot
- 7x LED, 1x button
- UART, (E)JTAG and LED headers
- 1x DC jack for main power (12-56 V)

Flash instruction (do it under U-Boot, using UART):

1. tftp 0x82000000 lede-ar71xx-generic-dr342-squashfs-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Piotr Dymacz
a4bb13e720 ar71xx: fix typo in Kconfig.openwrt
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-11-14 22:36:46 +01:00
Rosen Penev
e555153807 ag71xx: Switch from driver to kernel macro for NAPI_WEIGHT.
NAPI_POLL_WEIGHT was introduced in the kernel for exactly this purpose 5 years ago.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-11-06 16:39:41 +01:00
Felix Fietkau
1c68fd6d75 ar71xx: fix section mismatch in TP-Link Archer C7 v4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-11-05 18:52:14 +01:00
Florian Beier
c4c72a9a42 ar71xx: fix LED config for DIR-869 A1
This fixes the LED configuration for the D-Link DIR-869 A1. In order to
support the device I probed around using an initramfs image for the
UniFi AC. Pulling GPIO 15 to low enabled the LEDs while high disabled them.
GPIO 16 set to low meant that the color was white while pulling it to high
made the color change to orange. The past code was written based upon these
findings.
However, running a flashed image I now discovered that GPIO 15 controls the
orange LEDs while GPIO 16 controls the white ones and that both are active
when low. This means that the GPIOs were inverted and one active_low was set
wrong which this patch fixes.

Behavior of the LED front after this patch is applied:

cat /sys/devices/platform/leds-gpio/leds/d-link:white:status/brightness
0   -> white LEDs are OFF
255 -> white LEDs are ON

cat /sys/devices/platform/leds-gpio/leds/d-link🍊status/brightness
0   -> orange LEDs are OFF
255 -> orange LEDs are ON

If the brightness of both is set to 255 the LED front will be white.
If the brightness of both is set to 0 the LED front will be off.

Signed-off-by: Florian Beier <beier.florian@gmail.com>
2017-11-03 20:04:52 +01:00
Mathias Kresin
f9311e4070 ar71xx: wzr-hp-ag300h: drop unused wmac led_pin settings
The GPIOs are used for defined LEDs and therefore are ignored/unset in
the ath9k driver since 192f0a3db8. The wireless led led trigger is
added in userspace since e20965811d, which makes the
ap9x_pci_setup_wmac_led_pin() superfluous.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-11-03 20:04:52 +01:00
Thibaut VARENE
dfa2930988 ar71xx: mach-rbspi: fix 74x164 support
The platform data was missing the num_registers element which is now
mandatory in linux 4.9

Without this patch, the gpio probing would fail with:
gpio gpiochip1: (74x164): tried to insert a GPIO chip with zero lines

Fixes: #1106

Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-11-03 20:04:51 +01:00
Paul Wassi
080061c1ba ar71xx: fix LED names for GL-AR150
Add the respective colour to the LED's names for the GL-AR150 to be conform
to the kernel. Also add netdev triggers for the LAN and WAN LED.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2017-10-25 09:22:13 +02:00
Felix Fietkau
7c09fa4a74 ar71xx: fix mikrotik routerboard nand driver issues with linux 4.9
The mtd device is now embedded inside the nand chip data structure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-24 13:24:04 +02:00
Felix Fietkau
65da6f9ca1 ar71xx: fix secondary gpio controller base values
In 4.9, gpio count is rounded up to 32 due to the use of bgpio in the
ath79 gpio controller driver.
Fix base values in mach files to account for that

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-24 13:24:04 +02:00
Felix Fietkau
9887afb1af ar71xx: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9561+QCA9888.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f040000 +$filesize
3. cp.b $fileaddr 0x9f040000 $filesize
4. reset

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 16:14:19 +02:00
Felix Fietkau
2c9aff289e ar71xx: add support for Nokia WI2A-AC200i
Specifications:
 - SoC: Qualcomm QCA9558 (720 MHz)
 - RAM: 256MB
 - Storage: 1MB NOR, 128 MB NAND flash
 - Ethernet: 1x1000M

Installation:
 1. Connect to serial console on the board
 2. Boot initramfs image over u-boot
 3. Copy image to the device and run sysupgrade

Installation without serial console is not supported at this time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-19 12:27:42 +02:00
Felix Fietkau
3db529d5cc Revert "ar71xx: Add GRO support to ag71xx"
This reverts commit 13e5e47369.
This commit causes a severe regression in LAN->WAN routing performance
for several devices. This appears to be caused by the extra requirement
to validate the SKB checksum early in the rx path, which the ethernet
hardware does not do

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-17 16:03:11 +02:00
Robert Marko
443abb8ccd ar71xx: add support for Mikrotik RB750P-PBr2
Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 4 PoE out)
- Outdoor use ready

This ethernet router is based on the same platform as the hEX PoE lite.

Installation

1. login to the Mikrotik WebUI to backup your licence keys
2. setup a DHCP/BOOTP Server with:
     * DHCP-Option 66 (TFTP server name) pointing to a local TFTP
       Server within the same subnet of the DHCP range
     * DHCP-Option 67 (Bootfile-Name) matching the initramfs filename
       of the to be booted image
3. connect the port labled internet to your local network
4. keep the reset button pushed down and power on the board

The board should load and start the initramfs image from the TFTP
Server. Login as root/without password to the started LEDE via ssh
listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE.

Revert to RouterOS

Use the "rbcfg" package on in LEDE:
  * rbcfg set boot_protocol bootp
  * rbcfg set boot_device ethnand
  * rbcfg apply

Open Netinstall and reboot routerboard. Now netinstall sees routerboard
and you can install RouterOS. If NetInstall gets stuck on Sending offer
just wait for it to timeout and then close and open Netinstall again.

Click on install again.

In order for RouterOS to function properly, you need to restore license
for the device. You can do that by including license in NetInstall

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-10-14 10:48:29 +02:00
Hauke Mehrtens
27f23bac8f ar71xx: fix section mismatches
Fix some section mismatches found with kernel 4.9.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-11 22:36:04 +02:00
Hauke Mehrtens
7bbf4117c6 ar71xx: Add kernel 4.9 support
This add support for kernel 4.9 to the ar71xx target.
It was compile tested with the generic, NAND and mikrotik subtarget.
Multiple members of the community tested it on their boards and did not
report any major problem so far.

Especially the NAND part received some changes to adapt to the new
kernel APIs. The serial driver hack used for the Arduino Yun was not
ported because the kernel changed there a lot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-10-11 22:32:39 +02:00
Catrinel Catrinescu
b9c31c44d7 ar71xx: update LED definitions for embedded wireless dorin
Evaluation board 2.2 uses a different status LED pin
The other removed LEDs were never present

Signed-off-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-10-07 09:20:41 +02:00
Matthias Schiffer
53839da46e
ar71xx: fix MAC addresses on TP-Link TL-WR1043ND v4
The addresses were read from the 'config' partition, which would not always
contain the addresses at the same offsets, depending on the stock firmware
version used before flashing LEDE. Change this to get the addresses from
the 'product-info' partition, which is read-only.

Reported-and-tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2017-09-11 19:47:19 +02:00
Rosen Penev
13e5e47369 ar71xx: Add GRO support to ag71xx
On a TL-WN710N, this patch increases iperf performance from ~92.5 to ~93.5 mbps. Keep in mind the WN710N is a 100mbps device. I expect greater numbers from gigabit devices.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2017-09-11 17:12:42 +02:00
Enrique Giraldo
71067e3b79 ar71xx: wpj558: remove unused eth1 device and fix MAC address
Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
2017-09-10 22:15:04 +02:00
Enrique Giraldo
fefdb1e0b9 ar71xx: add support for COMFAST CF-E355AC
COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on
Qualcomm/Atheros QCA9531 + QCA9882.

Short specification:

- 2x 10/100 Mbps Ethernet, with PoE support
- 64MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n
- 2T2R 5 GHz, 802.11ac/n/a
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- built-in watchdog chipset

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
[whitespace fixes, ac radio caldata offset fix]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:15:03 +02:00
Piotr Dymacz
90d8c0f0a2 ar71xx: add support for GL.iNet GL-USB150
GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4)
- 1T1R 2.4 GHz
- 2x LED, 1x button
- UART header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used
to flash LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-09-10 22:14:43 +02:00
Kuang Rufan
69323a0c07 ar71xx: add support for TL-WR1041N(v2) LAN/WAN LEDs.
1. Add support to LAN/WAN LEDs attached to ar8327.
2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto)
   mode when connected to 10M/100M ethernet.

Signed-off-by: Kuang Rufan <master@a1983.com.cn>
2017-09-04 12:48:23 +02:00
Piotr Dymacz
0c6165d21a ar71xx: add support for ALFA Network AP121F
ALFA Network AP121F is a pocket-size router dedicated for VPN/TOR users.
Device is based on Atheros AR9331 WiSoC and is running a custom version
(updated from OpenWrt CC to LEDE 17.01 release) of NetAidKit firmware.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz
- 1x microSD (optional, on separate PCB)
- 3x LED, 1x button, 1x switch
- UART header on PCB

Flash instruction (under U-Boot web recovery mode):

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
   wait for first blink of all LEDs (indicates network setup), then keep
   button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-22 23:13:55 +02:00
Milan Krstić
4c1ce83548 ag71xx: add support for port mirroring
This exposes hardware port mirroring in ag71xx driver (e.g. TL-WR841ND) via
swconfig API.

Signed-off-by: Milan Krstić <milan.krstic@gmail.com>
2017-07-21 08:10:38 +02:00
Sergey Ryazanov
6cad8ee0bd ar71xx: keep the RouterBOARD Power LED in On state
It is quite unexpected behaviour when the Power LED switches off as soon
as the kernel starts booting. So set the default state to 'Keep' for
the Power LEDs of all RouterBOARDs (e.g. RB91x, SXT Lite series, etc.).

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
[switch the default state to keep instead of on]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-20 19:10:29 +02:00
Piotr Dymacz
befc763ed1 ar71xx: support LED in TP-Link TL-WR902AC RJ45 socket
TP-Link TL-WR902AC has another one, tiny LED inside RJ45 socket which is
attached to GPIO15. Add support for it, use it as a "lan" LED and rename
old one to "internet". Also, fix uci option name for "lan" LED in system
configuration ("wan" -> "lan").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-09 23:44:20 +02:00
Piotr Dymacz
6165e4aab0 ar71xx: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.

Specification:

- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
  resitors are missing on TX/RX lines)
- 1x micro USB (for power only)

Flash instructions:

Use "factory" image under vendor GUI.

Recovery instructions:

This device contains tftp recovery mode inside U-Boot. You can use it to
flash LEDE (use "factory" image) or vendor firmware.

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ar71xx-generic-tl-wr902ac-v1-squashfs-factory.bin"
   to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
   and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.

Root access over serial line in vendor firmware: root/sohoadmin.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-07-04 08:58:54 +02:00
Henryk Heisig
b05c7193fd ar71xx: add support for TP-Link Archer C58 v1
TP-Link Archer C58 v1 is a dual-band AC1350 router, based on Qualcomm
QCA9561 + QCA9886. It looks like Archer C59 v1 without USB port.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 3x button
- UART header on PCB, RX, TX at TP4+5 (backside)

QCA9886 wlan needs pre_cal_data file and enable ieee80211 phy hotplug to
patch macaddress.

Flash instruction:

Use "factory" image directly in vendor GUI.

Recovery method:

1. Set PC to fixed ip address 192.168.0.66/24.
2. Download "lede-ar71xx-generic-archer-c58-v1-squashfs-factory.bin" and
   rename it to "tp_recovery.bin".
3. Start a tftp server with the file "tp_recovery.bin" in its root
   directory.
4. Turn off the router.
5. Press and hold Reset button.
6. Turn on router with the reset button pressed and wait ~15 seconds.
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server.
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f020000 +$filesize
cp.b $fileaddr 0x9f020000 $filesize
reset

This commit is based on GitHub PR#1112

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2017-06-29 10:37:36 +02:00
Federico Cappon
9fec39a033 ar71xx: add support for TP-Link TL-WA855RE v1
TP-Link TL-WA855RE v1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/397/198 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 2x LED (green and orange in the same package), 2x button
- UART: TP5(TX) and TP4(RX) test points on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.

Signed-off-by: Federico Cappon <dududede371@gmail.com>
2017-06-29 10:37:36 +02:00
Leon M. George
98c5a71dfd ar71xx: wpj344: remove unused eth1 device
Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Leon M. George
c777fd8a7e ar71xx: wpj344: read MAC addresses from u-boot mtd
This way, the assigned addresses match those on the barcode labels.
Otherwise, the addresses appear to vary on boot.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2017-06-29 10:37:36 +02:00
Mathias Kresin
e7cd6f5d66 ar71xx: add AVM FRITZ!WLAN Repeater 300E support
Specifications:
* SoC: AR7242 (Virian 400MHz)
* RAM: 64 MB DDR (W9751G6JB-25)
* Flash: 16MB SPI flash (S25FL129PIF)
* WiFi: AR9382 (2.4/5GHz) + 2x SE2595L
* LAN: 1x1000M (PEF7071V)

To install LEDE via EVA bootloader, a FTP connection need to be
established to 192.168.178.1 within the first seconds after power on:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put lede-ar71xx-generic-fritz300e-squashfs-sysupgrade.bin mtd1

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Ludwig Thomeczek
b4711dbad3 ar71xx: add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip.

Signed-off-by: Ludwig Thomeczek <ledesrc@wxorx.net>
[minor code style fixes, boards alphabetical order fixes,
reworked commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-11 21:32:18 +02:00