/etc/config/mdadm is only used by the init script which is ran as root.
There is no need for it to be readable by anything else.
Added PKG_CPE_ID for proper CVE tracking.
Small reorganization for consistency between Makefiles.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The hotplug file is ran by procd, which runs as root. The config file is
used by the init script, which also runs as root.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
/etc/config/lldpd is only used by the init script, which only runs as root
Adjusted homepage and download URLs to use HTTPS.
-std=c99 is useful for GCC versions less than 6. Current OpenWrt uses 7.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Setting encaplimit to a numerical value results into the value being
included as tunnel encapsulation limit in the destination option header
for tunneled packets.
Several users have reported interop issues as not all ISPs support the
destination option header containing the tunnel encapsulation limit
resulting into broken map connectivity.
Therefore drop the default encaplimit value for map tunnels so
no destination option header is included by default.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Setting encaplimit to a numerical value results into the value being
included as tunnel encapsulation limit in the destination option header
for tunneled packets.
Several users have reported interop issues as not all ISPs support the
destination option header containing the tunnel encapsulation limit
resulting into broken ds-lite connectivity.
Therefore drop the default encaplimit value for ds-lite tunnels so
no destination option header is included by default.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* blake2s-x86_64: fix whitespace errors
* crypto: do not use compound literals in selftests
* crypto: make sure UML is properly disabled
* kconfig: make NEON depend on CPU_V7
* poly1305: rename finish to final
* chacha20: add constant for words in block
* curve25519-x86_64: remove useless define
* poly1305: precompute 5*r in init instead of blocks
* chacha20-arm: swap scalar and neon functions
* simd: add __must_check annotation
* poly1305: do not require simd context for arch
* chacha20-x86_64: cascade down implementations
* crypto: pass simd by reference
* chacha20-x86_64: don't activate simd for small blocks
* poly1305-x86_64: don't activate simd for small blocks
* crypto: do not use -include trick
* crypto: turn Zinc into individual modules
* chacha20poly1305: relax simd between sg chunks
* chacha20-x86_64: more limited cascade
* crypto: allow for disabling simd in zinc modules
* poly1305-x86_64: show full struct for state
* chacha20-x86_64: use correct cut off for avx512-vl
* curve25519-arm: only compile if symbols will be used
* chacha20poly1305: add __init to selftest helper functions
* chacha20: add independent self test
Tons of improvements all around the board to our cryptography library,
including some performance boosts with how we handle SIMD for small packets.
* send/receive: reduce number of sg entries
This quells a powerpc stack usage warning.
* global: remove non-essential inline annotations
We now allow the compiler to determine whether or not to inline certain
functions, while still manually choosing so for a few performance-critical
sections.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
usign occasionally writes 16 characters then exits without writing a LF,
leaving ucert hanging waiting for more input. Accept 16 characters
or more rather than 17 to work around the short read.
Signed-off-by: Mike McCormack <mike@atratus.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Refreshed all patches.
Added new patch:
- 192-Revert-ubifs-xattr-Don-t-operate-on-deleted-inodes.patch
This fixes a bug introduced in upstream 4.14.68 which caused targets using
ubifs to produce file-system errors on boot, rendering them useless.
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Allow setting specific routing tables via the ip4table and ip6table
options also when ${ifname}_4 and ${ifname}_6 child interfaces are
being created.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Pull in latest upstream tweaks:
Similar to the previous patch for no-split-gso, the negative keywords for
'nat', 'wash' and 'ack-filter' were not printed either. Add those as well.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
When the GSO splitting was turned into dual split-gso/no-split-gso options,
the printing of the latter was left out. Add that, so output is consistent
with the options passed
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bump to latest upstream cake:
Add workaround for wrong skb->mac_len values after splitting GSO
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
On some systems (Gentoo) configure stage fails because of docbook2man
working with SGML rather than with XML. We don't need xmlwf man pages so
we disable this.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* curve25519: arm: do not modify sp directly
* compat: support neon.h on old kernels
* compat: arch-namespace certain includes
* compat: move simd.h from crypto to compat since it's going upstream
This fixes a decent amount of compat breakage and thumb2-mode breakage
introduced by our move to Zinc.
* crypto: use CRYPTOGAMS license
Rather than using code from OpenSSL, use code directly from AndyP.
* poly1305: rewrite self tests from scratch
* poly1305: switch to donna
This makes our C Poly1305 implementation a bit more intensely tested and also
faster, especially on 64-bit systems. It also sets the stage for moving to a
HACL* implementation when that's ready.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* add missing 'rpcbind' alias to /etc/services
Allows rpcbind to open its 111 port and be reachable via lan, this is the default behaviour.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
Kernel upstream commit 67a3ba25aa95 ("MIPS: Fix incorrect mem=X@Y handling") introduced a new issue for rt288x where "PHYS_OFFSET" is 0x0 but the calculated "ramstart" is not. As the prerequisite of custom memory map has been removed, this results in the full memory range of 0x0 - 0x8000000 to be marked as reserved
for this platform.
This patch adds the originally intended prerequisite again.
Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
The OM2P(-HS)v4 got a variant which uses a slightly different flash. The
standard versions used a flash with 256KB blocks which is no longer
available. The replacement flash uses a flash with 64K blocks.
The padding for the image rootfs is already for 64K and 256K and thus can
be flashed on the device without any problems. Unfortunately, the
bootloader will check $rootfs_size (rounded down to the nearest 64k block)
minus 1x 64k. But it is now possible that the new JFFS2 rootfs_data starts
even earlier and modifies the checked region. The check will then fail and
the backup image (when available) will be booted.
Just setting it to the same number of skipped blocks as other 64K models
avoids this problem.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM family.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM family, the mapping for rssileds monitor was omitted
by mistake. Therefore create the mapping, so RSSI LEDs work without
additional configuration, after starting rssileds service.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
Some systems require multiple flash chips to be concatenated and read as
a single mtd device. The ar71xx target provides custom code to create
such mtdconcat devices. When porting devices to ath79, however, there is
no way to create such devices from within the device tree.
This commit adds a driver for creating virtual mtd-concat devices to the
ath79 target. Nodes must have a compatible = "virtual,mtd-concat" line,
and define a list of devices to concat in the 'devices' property,
for example:
flash {
compatible = "virtual,mtd-concat";
devices = <&flash0 &flash1>;
};
The driver is added to the very end of the mtd Makefile to increase the
likelyhood of all child devices already being loaded at the time of
probing, preventing unnecessary deferred probes which might in turn
cause other problems (like failure to load MAC addresses from art because
the partitions are not loaded yet).
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm
Atheros QCA9563.
Specification:
- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4 GHz wifi
- SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 4x keys(connected to GPIO: 3x)
- UART header on PCB
- TX, GND, RX, Vcc from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Boot the WRC-300GHBK2-I normaly and connect the computer to its
LAN port
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新 手動更新（アップデート）")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, execute "mtd erase firmware" to
erase stock firmware and execute sysupgrade with squashfs-sysupgrade
image for WRC-300GHBK2-I
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
In addition to the default little-endianness format, I added a mode
so that we can generate firmware with big-endianness format.
example: ELECOM WRC-300GHBK2-I (QCA9563)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This is an upstream-applied patch that fixes 'PATH_MAX' and 'NAME_MAX'
undeclared when compiling on musl with CONFIG_PCAP_HAS_USB.
[aafa351] pcap-usb-linux.c: add missing limits.h for musl systems.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
This patch ports over support for the device from ar71xx.
SOC: AR7370 (Wasp - AR9344 rev2 0001974c)
RAM: Winbond W9725G6KB-25 32MiB
FLASH: Winbond 25Q64FVSIG 8MiB
WLAN: AR9380 Dual-Band 802.11abgn 3x3:3
INPUT: WPS, RESET button (hardware on/off toggle button)
LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high)
Serial: Header Next to the winbond flash chip (labeld JP1)
Pinout is GND - NC - RX - TX - 3V3 (JP1)
The Serial setting is 115200-8-N-1.
- Installation via uboot's upgrade command
0. attach serial cable
1. interrupt uboot and enter "upgrade code.bin" into
the u-boot prompt
ar7240> upgrade code.bin
2. rename openwrt...sysupgrade.bin to code.bin on PC
3. run a tftp-client on the PC
(shell)$ tftp 192.168.1.230
binary
put code.bin
4. wait for the device to finish
[...]
Copy buff to Flash from 0x9f040000 length 0x79f000
Copy to Flash... write addr: 9f040000
done
5. enter "go" in the u-boot prompt
ar7240> go
- TFTP ramdisk image boot from the uboot prompt
(tftp server defaults to serverip 192.168.1.254)
=> tftpboot 81000000 initramfs.bin
=> bootm
Tested and working:
- LEDs
- Buttons
- Ethernet
- Wi-Fi
- OpenWRT sysupgrade
For flashing and debricking information see:
<https://openwrt.org/toh/wd/rext>
Users coming from ar71xx can use sysupgrade too. But I highly
advise to no save the old configuration and start from a clean
state.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch ports the cybertan_part code from ar71xx and converts the
driver to a DT-supported mtd parser. As a result, it will no longer
add the u-boot, nvram and art partitions, which were never part of
the special Cybertan header.
Instead these partitions have to be specified in the DT, which has the
upside of making it possible to add properties (i.e.: read-only), labels
and references to these important partitions.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently it's close to impossible to tell what part of mac80211 setup
went wrong. Errors logged into system log look like this:
radio0 (6155): command failed: No error information (-524)
radio0 (6155): command failed: Not supported (-95)
radio0 (6155): command failed: I/O error (-5)
radio0 (6155): command failed: Too many open files in system (-23)
With this commit change it's getting clear:
command failed: No error information (-524)
Failed command: iw dev wlan0 del
command failed: Not supported (-95)
Failed command: iw phy phy0 set antenna_gain 0
command failed: I/O error (-5)
Failed command: iw phy phy0 set distance 0
command failed: Too many open files in system (-23)
Failed command: iw phy phy0 interface add wlan0 type __ap
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The board is made by Avnet, so rename it accordingly as
upstream has done it
Also move the device to maintain alphabetic order
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Implement the generation of sdcard images with ext4 or
squashfs + f2fs overlay, but only enable the latter
automatically
Additionally, add mkf2fs and e2fsprogs to default packages
to manipulate ext4 and f2fs filesystems
Finally, disable the automatic generation of initramfs
and rootfs.tar.gz images, as they are no longer required
(they can still be selected in menuconfig)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
