Drivers have been modified to use it and new ones have to be written
this way, so we need it for backporting code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This allows referencing USB ports/devices that are always present in a
device. This applies to some internal devices, root hub ports and
internal USB hubs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon and x86/64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
It was needed upstream to avoid bcma references in the main code. To
match this new code our patch adding SRAB was also updated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Instead of using off-the-tree .dts files for ARC boards we're
switching to use in-tree ones. And for that to work properly
we apply upstream patch that adds currently missing "model"
property.
Upstream patch and discussion could be found here:
http://lists.infradead.org/pipermail/linux-snps-arc/2016-August/001394.html
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
These 2 trivial patches will be followed by a bigger bgmac rework so
they are worth backporting in a separated patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes flash corruptions. It touches bcm47xxsflash driver shared
between brcm47xx and bcm53xx so put it in generic.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The bootmem area reserved for crashlog might be smaller than CRASHLOG_OFFSET
bytes, leading to an integer underflow when calculating the memory address
in crashlog_set_addr() which subsequently causes the kernel to crash when
attempting to vmap() the crashlog pages.
Change the logic to only consider the offset when the size of the used memory
area is sufficient.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
Backports upstream commit 75ff39ccc1bd5d3c455b6822ab09e533c551f758
to the used LEDE kernel versions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Due to the missing carrier status set, the interface wasn't usable on a
BTHOMEHUB2B after ip link down and up as it is done in preinit.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Check memblock regions for sufficient size before attempting to use
them. Allow checks for multiple memblock regions until a suitable one is
found.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Our code was assuming CPU port uses the highest number. My BCM53573
device has eth0 connected to port 8 and eth1 connected to port 5. While
working on support for it I tried to:
1) Enable all ports (including port 8)
2) Set CPU port to 5
I noticed port 8 is not accessible anymore. It was just a development
process but it seems like something worth fixing anyway.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
With that patch in place for initramfs no additional options are
reported for "/" partition. What's really important is missing
info about sizes. Which in its turn makes opkg think that there's
no space on "/" partition to install software.
I understand that's a sort of corner-case, people rarely install
packages on ramfs but anyways why not?
Just in case that's what I see with the patch:
---------------------->8--------------------
root@lede:/# cat /proc/mounts
rootfs / rootfs rw 0 0
proc /proc proc rw,nosuid,nodev,noexec,noatime 0 0
sysfs /sys sysfs rw,nosuid,nodev,noexec,noatime 0 0
tmpfs /tmp tmpfs rw,nosuid,nodev,noatime 0 0
tmpfs /dev tmpfs rw,nosuid,relatime,size=512k,mode=755 0 0
devpts /dev/pts devpts rw,nosuid,noexec,relatime,mode=600 0 0
debugfs /sys/kernel/debug debugfs rw,noatime 0 0
---------------------->8--------------------
And without:
---------------------->8--------------------
root@lede:/# cat /proc/mounts
rootfs / rootfs rw,size=256168k,nr_inodes=32021 0 0
proc /proc proc rw,nosuid,nodev,noexec,noatime 0 0
sysfs /sys sysfs rw,nosuid,nodev,noexec,noatime 0 0
tmpfs /tmp tmpfs rw,nosuid,nodev,noatime 0 0
tmpfs /dev tmpfs rw,nosuid,relatime,size=512k,mode=755 0 0
devpts /dev/pts devpts rw,nosuid,noexec,relatime,mode=600 0 0
debugfs /sys/kernel/debug debugfs rw,noatime 0 0
---------------------->8--------------------
Note how different is entry for rootfs.
And given there's no known rationale for that patch we're
getting rid of it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Felix Fietkau <nbd@nbd.name>
This is required to update bcma without build breakage. One of bcma
patches changes BCMA_SFLASH dependency.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
On UBI-enabled devices using squashfs as their rootfs an error
message like
UBIFS error (ubi0:3 pid 1): init_constants_early: too few LEBs (12), min. is 17
was thrown while probe-mounting the rootfs which later on succeeds and
thus shouldn't alert the user.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of disabling unwinding entirely this upstream patch
just disables generation of async unwind tables.
Once the patch in question lands in stable 4.4 tree this change
essentially must be removed (otherwise patch application will fail).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
When USB Wi-Fi dongle based on Atheros AR9271 is connected to OHCI
(USB 1.1) controller following warnings flood debug console:
------------------------>8---------------------------
usb 1-1: new full-speed USB device number 2 using ohci-platform
usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at drivers/usb/core/urb.c:450
usb_submit_urb+0x162/0x404
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Not tainted 4.6.3 #10
Workqueue: events request_firmware_work_func
Stack Trace:
arc_unwind_core.constprop.1+0x94/0x10c
---[ end trace 2249b79eac9991d1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at drivers/usb/core/urb.c:450 usb_submit_urb+0x162/0x404
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G W 4.6.3 #10
Workqueue: events request_firmware_work_func
Stack Trace:
arc_unwind_core.constprop.1+0x94/0x10c
---[ end trace 2249b79eac9991d2 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 4 at drivers/usb/core/urb.c:450 usb_submit_urb+0x162/0x404
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
Modules linked in:
CPU: 0 PID: 4 Comm: kworker/0:0 Tainted: G W 4.6.3 #10
Workqueue: events request_firmware_work_func
Stack Trace:
arc_unwind_core.constprop.1+0x94/0x10c
---[ end trace 2249b79eac9991d3 ]---
...
------------------------>8---------------------------
With removed warning Wi-Fi dongle works properly.
Even though this is not the best solution it gets us a working Wireless
AP. Anyways new discussion was started in linux-usb mailing list to find
a proper solution instead of that hack.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The kernel config option CONFIG_NET_UDP_TUNNEL is not visible and can
not directly be activated. When kmod-udptunnel4 or kmod-udptunnel6 are
build these packages could be empty when no other kernel module selects
CONFIG_NET_UDP_TUNNEL.
Reported-by: Baptiste Jonglez <baptiste@bitsofnetworks.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch is a backport for current LEDE 4.4 Kernels.
It is already upstream, for linux-next and stable.
The initial commit message is below:
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
This adds a configuration options that allows to make filesystem ACL support
the default in the kernel, except for old nfs.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
This patch is already included in the Linux mainline kernel since
v3.15, remove it from LEDE, see the lines directly before this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch was introduced in commit r16412 for the brcm47xx target only
and then moved to generic in commit r32395. It was initially added
because of ticket #5186 and should fix some problems with fuse file
systems and MIPS caches. The commit comment in r32395 says that this a
generic problem in MIPS CPUs, but does not name any specifics about
that. There was a fix added to kernel 2.6.21 in commit commit
7575a49f20 "[MIPS] Implement flush_anon_page()." that should fix this
problem, but that was already available before both commits were done
to OpenWrt.
I just tested fuse with ntfs.3g without this patch on a BCM4704
(BMIPS3300 V0.6) SoC and haven't seen any problems. Someone reported
that removing this patch improves some fuse operations by 5 times on
some modern MIPS cores.
My test was only a simple "dd if=/dev/zero of=/mnt/zero bs=5000" to an
USB stick.
This patch removes the patch to OpenWrt, because I assume that it is
not needed any more and Felix, the orginal author, also thinks so.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the upstream kernel and the upstream squashfs4 tools the xz
compression header looks the following:
struct disk_comp_opts {
__le32 dictionary_size;
__le32 flags;
};
We added some other members and also moved some existing members. Place
the members which are already in upstream header at the same position
as in that kernel and add our own at the end. The kernel should not
have a problem when there are some additional members and just ignore
them.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel 4.7 there is upstreamed b53 driver using (mostly?) the same
symbols as our b53 does. Change our symbols so both drivers can coexist
in kernel tree.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
So far "kernel" partition didn't contain just a kernel. It also included
Seama header and meta data. This was making kernel update complex and it
wasn't trivial to read kernel size.
Fix it by making "kernel" parition contain just a kernel image.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Despite the MS_SILENT flag being set when probing for ubifs rootfs a
logline indicating an error is generated during boot:
UBIFS error (pid: 1): cannot open "ubi0:rootfs", error -19
This leads to confusion and there shouldn't be lines containing
the word 'error' twice in a bootlog if actually everything is fine
(just the rootfs happens to be something else than ubifs)
The patch added has been submitted and was accepted upstream, see:
http://lists.infradead.org/pipermail/linux-mtd/2016-June/068056.htmlhttp://patchwork.ozlabs.org/patch/637491
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This can be used to prevent double compression for platforms where the
boot loader already expects compressed images.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The swconfig kernel infrastructure fails to do any permissions checks when
changing settings. As such an ordinary user account on a device with a
switch can change switch settings without any special permissions.
Routers generally have few non-admin users so this isn't a big hole, but it
is a security hole. Likely the greatest danger is for multifunction devices
which have a lot of extra daemons, compromising a low-security daemon would
allow one to modify switch settings and cause the router/switch to appear to
lock-up (or cause other sorts of troublesome nyetwork behavior).
Implement a check for CAP_NET_ADMIN in swconfig_set_attr() and deny any
requests originating from user contexts lacking this capability.
Reported-by: Elliott Mitchell <ehem+openwrt@m5p.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
OpenWRT changed the default fq_codel sch->limit from 10240 to 1024,
without also adjusting q->flows_cnt. Eric Dumazet explains below that
you must also adjust the buckets (q->flows_cnt) for this not to break.
Eric explains: Limit of 1024 packets and 1024 flows is not wise I think.
(If all buckets are in use, each bucket has a virtual queue of 1 packet,
which is almost the same than having no queue at all)
I suggest to have at least 8 packets per bucket, to let Codel have a
chance to trigger. So you could either reduce number of buckets to 128
(if memory is tight), or increase limit to 8192.
flows_cnt is now set to 1024/8=128
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Building for octeon fails with
'arch/mips/vdso/vdso-n32.so.dbg' already contains a '.MIPS.abiflags'
section
if the file already exists from a prior build.
Use the same workaround as the one for vdso.so.dbg committed in
9eb155353a.
Commit 91f205acaf extended the workaround
to cover vdso-o32.so.dbg but missed the vdso-n32.so.dbg which is added
now by this change.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Building for octeon fails with
'arch/mips/vdso/vdso-o32.so.dbg' already contains a '.MIPS.abiflags'
section
if the file already exists from a prior build.
Use the same workaround as the one for vdso.so.dbg committed in
9eb155353a.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Currently the build fails with
'arch/mips/vdso/vdso.so.dbg' already contains a '.MIPS.abiflags' section
if the file already exists from a prior build.
Add a makefile rule to force the rebuild of vdso.so.dbg if genvdso has
has been changed to workaround the failure.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This enables misaligned access handling by software in Linux kernel.
With some wireless drivers (ath9k-htc and mt7601u for example) we see
misaligned accesses here and there and to cope with that without
fixing stuff in the drivers we're just gracefully handling it on ARC.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 49134
The current code only partially invalidates both caches
because the cache size and cache-line size values are
incorrectly passed to the C code.
Fix the assembly code to pass the arguments in the correct
order.
Tested on RB532.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 49056
The function memblock_insert_region() is in the section
__init_memblock, also put crashlog_init_memblock there.
This fixes this section mismatch warning:
The function memblock_insert_region.isra.1() references
the function __meminit crashlog_init_memblock().
This is often because memblock_insert_region.isra.1 lacks a __meminit
annotation or the annotation of crashlog_init_memblock is wrong.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48931
The buildbots complained about these config options being missing for arm64:
CONFIG_DUMMY_CONSOLE_COLUMNS=80
CONFIG_DUMMY_CONSOLE_ROWS=25
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48929
Combine all bus operations for one MMD access in one function.
Protecting all these bus operations with one lock also helps
to avoid potential issues due to bus operations intercepting
the register and data write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48914
The default TTL for address resolution table entries is 5 minutes
for all members of the AR8216 family. This can cause issues if
e.g. Wifi clients roam to another AP and their MAC appears on
another switch port suddenly. Then the client may not be reachable
until the old ARL entry expires.
I would have expected the switch to invalidate old entries if it
detects the same MAC on another port. But that's not the case.
Therefore make the TTL for ARL entries configurable.
The effective TTL will always be a multiple of 7 seconds.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48913
The line before includes the port number anyway so there's no need
to duplicate the port number in the MIB info header.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48912
The decimal values especially for TxByte and RxGoodByte are hard to read
once bigger amounts of data have been transferred.
Therefore complement the decimal values with info in GiB / MiB / KiB.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48911
For unused switch ports all MIB values are zero. Displaying ~40 empty
MIB counters is just confusing and makes it hard to read the output of
swconfig dev <dev> show.
Therefore, if all MIB counters for a port are zero, just display
an info that the MIB counters are empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 48910
Enable platform-supplied WLAN LED name for ath9k device.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
SVN-Revision: 48879
The vdso version of this function has some problems with the cache.
Very often it works on dated data which causes problem. We are
currently working on fixing this in upstream Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 48787
This patch adds speed_mask special file to LEDs connected to switch ports
via 'switch' trigger. It allows to choose which speeds to signal when link
is up. If router has more than one LED per port, they may light up
differently depending on how fast connection is. Default setting is 'all
speeds' so backward compatibility with system scripts (for example uci) is
maintained.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48775
This patch changes swconfig_trig_port_mask_store() handler to utilize
kstrtoul() function instead of call to obsolete simple_strtoul(). Thanks
to this change, new handler takes less memory and makes port_mask special
file accept not only hexadecimal, but also decimal and octal numbers.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
SVN-Revision: 48774
Seama format has 2 similar headers: container (seal) header and entity
header. The first one has size always set to 0 and doesn't contain MD5
digest.
When dealing with Seama on a flash we deal directly with an entity. You
can see mtdsplit_parse_seama reads from offset 0 and expects entity to
be there. Seama container is used by bootloader / interface only which
extract entity out of it and flash it.
That said we should fix our header struct. This is important as we
calculate possible rootfs offset assuming it may be placed right after
Seama entity. So far calculate offset was always 16B too low.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48754
When dealing with Broadcom hardware we can simply use swconfig's generic
helper, we just need to do some validation of requested state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 48623
