Commit graph

2286 commits

Author SHA1 Message Date
Gabor Juhos
47dfbb5bc6 ar71xx: rb95x: use correct SPI flash address
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.

Compile tested only.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39891
2014-03-12 12:52:39 +00:00
Gabor Juhos
25e870eed6 ar71xx: ar934x_nfc: fix memory initialization bug
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type)  * array_size   should be used in memset.

Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39890
2014-03-12 12:52:36 +00:00
Felix Fietkau
802d17ceaf ar71xx: Add 16MB Flash version for Embedded Wireless Dorin Platform
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>

SVN-Revision: 39764
2014-02-28 11:08:14 +00:00
Felix Fietkau
d83750083d ar71xx: adjust ew-dorin platform for LAN+WAN setup
Signed-off-by: Embedded Wireless GmbH <info at embeddedwireless.de>

SVN-Revision: 39763
2014-02-28 11:08:04 +00:00
Gabor Juhos
e9c80a1224 ar71xx: fix failsafe acces on several devices
The ar71xx platform always uses the eth0 interface to provide
access to the device in failsafe mode. Due to this, failsafe
access is broken on devices where the LAN ports are connected
to the 'eth1' interface.

Update the relevant script to correctly set the ifname variable
for these devices.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39752
2014-02-25 17:40:04 +00:00
Gabor Juhos
f677b1bc7e kernel: update 3.10 to 3.10.32
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39707
2014-02-23 10:59:40 +00:00
Gabor Juhos
590bafe3de ar71xx: define status LED for the RB91x boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39705
2014-02-23 08:11:54 +00:00
Gabor Juhos
da2f3c1448 ar71xx: rb91x: register GPIO LEDs
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39704
2014-02-23 08:11:53 +00:00
Gabor Juhos
14d95026b2 ar71xx: rb91x: add SPI device for the serial shift register
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.

Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39703
2014-02-23 08:11:52 +00:00
Gabor Juhos
7b89005f0d ar71xx/mikrotik: enable the 74x164 GPIO driver
That will be used to drive the 74HC595 serial-in/parallel-out
8-bits shift register which can be found on some RouterBOARDs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39702
2014-02-23 08:11:50 +00:00
Gabor Juhos
5f224ef8a3 ar71xx: improve platform device support in the gpio-74x164 driver
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39701
2014-02-23 08:11:49 +00:00
Gabor Juhos
3d906ac6ac ar71xx: rb91x-nand: rewrite to use GPIO API
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39700
2014-02-23 07:19:32 +00:00
Gabor Juhos
8fea668cb7 ar71xx: rb91x: register a gpio-latch platform device
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39699
2014-02-22 18:05:32 +00:00
Gabor Juhos
da5caba072 ar71xx/mikrotik: enable the GPIO latch driver
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39698
2014-02-22 18:05:31 +00:00
Gabor Juhos
ab08c40487 ar71xx: add a generic GPIO latch driver
It will be used for the Mikrotik boards.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39697
2014-02-22 18:05:29 +00:00
Gabor Juhos
be18a3849b ar71xx/mikrotik: enable small sector erase in the m25p80 driver
The serial flash devices used on the ROuterBOARDs are
supporting 4KiB erase blocks. Enable the small sector
erase option in the m25p80 driver to avoid superfluous
erase/write of adjacent blocks.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39696
2014-02-22 16:26:55 +00:00
Gabor Juhos
b7539ab109 ar71xx: spi-ath79: fix initial GPIO CS line setup
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39695
2014-02-22 16:17:28 +00:00
Gabor Juhos
3e6c7ed4f2 ar71xx: refresh unaligned access hacks patch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39694
2014-02-22 16:17:27 +00:00
Gabor Juhos
4e0309630b ar71xx: rb91x: fix pll_1000 value for eth0 to avoid packet loss
When the RB91x device uses a GbE link the connection
suffers from packet loss:

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 20 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  20 packets transmitted, 9 packets received, 55% packet loss
  round-trip min/avg/max = 4.570/4.815/4.999 ms

Using a different PLL value fixes the issue.

  root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 100 -q
  PING 192.168.1.254 (192.168.1.254): 65507 data bytes

  --- 192.168.1.254 ping statistics ---
  100 packets transmitted, 100 packets received, 0% packet loss
  round-trip min/avg/max = 4.449/5.413/13.870 ms

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39642
2014-02-20 17:07:56 +00:00
Gabor Juhos
d19b868b12 ar71xx: Add support for MikroTik RB951Ui-2HnD
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result.  I have cleaned up this patch.

When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.

This patch applies cleanly to SVN 39392.

Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
  - drop the 'rb951ui_wlan_init' function and rework the code to
    use the recently introduced rb95x_wlan_init function instead,
  - fix GPIO number of the port5 LED,
  - rename LEDs according to the standard LED naming conventions,
    and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39641
2014-02-20 17:07:51 +00:00
Gabor Juhos
f433088d50 ar71xx: add profile and build image for TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4850/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39637
2014-02-19 12:15:35 +00:00
Gabor Juhos
7ec2d80ae3 ar71xx: add user-space support for TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4849/
[juhosg:
  - use the Archer C7 specific LED setup instead of adding
    identical code]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39636
2014-02-19 12:15:34 +00:00
Gabor Juhos
db0e6e264d ar71xx: add kernel support for the TP-Link TL-WDR4900 v2.0 board
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4848/
[juhosg:
  - rename and refresh kernel patch,
  - merge the board setup code into mach-archer-c7.c and drop
    mach-tl-wdr49000-v2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39635
2014-02-19 12:15:32 +00:00
Gabor Juhos
6b8eb55ddb ar71xx: fix unaligned access hacks for tcp timestamps
This missing bit of the hack saves hugely on instruction traps
on tcp connections to ar71xx based routers.

Patch-by: Dave Taht <dave.taht@bufferbloat.net>
Patchwork: http://patchwork.openwrt.org/patch/4905/
[juhosg: adjust subject, refresh kernel patch]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39626
2014-02-18 17:34:17 +00:00
Gabor Juhos
d6cb5215a9 ar71xx: WNR2200: fix mounting root fs problem
Solves ticket #14356 <https://dev.openwrt.org/ticket/14356>

Without this patch, UART output will show only 4 partitions:
  [    0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
  [    0.750000] Creating 4 MTD partitions on "spi0.0":
  [    0.750000] 0x000000000000-0x000000050000 : "u-boot"
  [    0.760000] 0x000000050000-0x000000070000 : "u-boot-env"
  [    0.770000] 0x000000070000-0x0000007f0000 : "firmware"
  [    0.790000] 0x0000007f0000-0x000000800000 : "art"
and then linux complains :VFS: Cannot open root device "(null)"

With this patch, UART out will show 7 partitions:
  [    0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
  [    0.750000] Creating 4 MTD partitions on "spi0.0":
  [    0.750000] 0x000000000000-0x000000040000 : "u-boot"
  [    0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
  [    0.770000] 0x000000050000-0x0000007f0000 : "firmware"
  [    0.780000] 2 netgear-fw partitions found on MTD device firmware
  [    0.780000] 0x000000050000-0x00000014b440 : "kernel"
  [    0.790000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  [    0.800000] 0x00000014b440-0x0000007f0000 : "rootfs"
  [    0.810000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  [    0.820000] mtd: device 4 (rootfs) set to be root filesystem
  [    0.830000] 1 squashfs-split partitions found on MTD device rootfs
  [    0.830000] 0x000000340000-0x0000007f0000 : "rootfs_data"
  [    0.840000] 0x0000007f0000-0x000000800000 : "art"

This patch is tested against r39502 of trunk.

Signed-off-by: Jonathan Chang <changcs@santos.ee.ntu.edu.tw>
Patchwork: http://patchwork.openwrt.org/patch/4870/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39625
2014-02-18 17:34:16 +00:00
Jo-Philipp Wich
b1d7ebae09 ar71xx: fix mtdpartsize macro in image Makefile (#14961)
The mtdpartsize macro triggers shell errors on various Linux distributions
when the partname argument $(1) does not appear within the partmap $(2).

Change the sed pattern to only emit anything if a successful substitution
occured and only evaluate the arithmetic expression if something was printed
by the sed program.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 39583
2014-02-13 21:19:00 +00:00
Gabor Juhos
037b42838f ar71xx: dragino2: add missing sysupgrade support.
The original dragino2 board support was missing some changes from the
upstream svn repository (http://svn.dragino.com/dragino2) that supported
sysupgrade.

[juhosg: change subject]

Signed-off-by: Karl Palsson <karlp@remake.is>
Patchwork: http://patchwork.openwrt.org/patch/4801/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39429
2014-01-30 17:08:02 +00:00
Gabor Juhos
3b8c51771d ar71xx: wpe72: set active_low flag for the reset button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39401
2014-01-26 14:55:34 +00:00
Gabor Juhos
b503dc026e ar71xx: wp543: set active_low flag for the buttons
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39400
2014-01-26 14:55:32 +00:00
Gabor Juhos
a2543d72d8 kernel: update 3.10 to 3.10.28
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39399
2014-01-26 11:30:34 +00:00
Gabor Juhos
e41e531e3b ar71xx: image: reserve 4 erase blocks on the TP-Link devices
This ensures that the generated images will have enough erase
blocks for JFFS2.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39397
2014-01-25 18:12:13 +00:00
Gabor Juhos
50f38063cd ar71xx: archer c7: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39395
2014-01-25 11:16:59 +00:00
Gabor Juhos
f1a9ed8345 ar71xx: image: move WNDAP360 macro
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39394
2014-01-25 08:31:45 +00:00
Gabor Juhos
f85231257e ar71xx: fix bad RX sensitivity on newer TL-WDR4300 boards
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.

Setup the GPIOs of the external LNAs to fix the issue.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39392
2014-01-24 17:40:17 +00:00
Gabor Juhos
09bf46d418 ar71xx: image: generate sysupgrade images for the Compex boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39391
2014-01-24 17:15:03 +00:00
Gabor Juhos
252e906dda ar71xx: add sysupgrade support for the Compex boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39390
2014-01-24 17:15:02 +00:00
Gabor Juhos
0c0b87293e ar71xx: image: use a single firmware partition on Compex devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39389
2014-01-24 17:15:01 +00:00
Gabor Juhos
2995030b47 ar71xx: enable MTD_SPLIT_LZMA_FW option
It will be used for Compex devices.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39388
2014-01-24 17:15:01 +00:00
Gabor Juhos
998c89a9a6 ar71xx: image: detect partition sizes in the Image/Build/Ath macro
Get the size of the mtd partitions directly from the
MTD layout and remove the superfluous macro parameters.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39384
2014-01-24 11:59:35 +00:00
Gabor Juhos
4556632578 ar71xx: image: fix size verification in the CatFiles macro
The macro checks the size of the rootfs image even if
the second parameter of the macro contains the size of
an eraseblock. It is wrong because the size of the
kernel image will be adjusted to the next eraseblock
and the resulting image might be too large.

Fix the macro to check the size of the final image
instead of the rootfs image.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39383
2014-01-24 11:59:32 +00:00
Gabor Juhos
56136c0f34 ar71xx: ap83: define mtd layout via command line
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39379
2014-01-23 16:47:42 +00:00
Gabor Juhos
a59e82761f ar71xx: ap81: define mtd layout via command line
Also use the RKuImage macro becasue the original
firmware starts with the rootfs.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39378
2014-01-23 16:47:41 +00:00
Gabor Juhos
9f4e2bf326 ar71xx: image: show size limit in warning messages
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39376
2014-01-23 12:27:28 +00:00
Gabor Juhos
447530995a ar71xx: add initramfs image support for Compex devices
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39375
2014-01-23 12:23:10 +00:00
Gabor Juhos
b629009eaa ar71xx: wp543: use KEY_RESET code for the sw4 button
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39374
2014-01-23 12:23:08 +00:00
Luka Perkov
cbc892a549 ar71xx: create wndr3700 network config from uci-defaults
Since that was the last configuration in defconfig directory we can drop the
defconfig init script too.

Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 39373
2014-01-23 11:33:42 +00:00
Gabor Juhos
0b599c51cc ar71xx: mynet-n750: define LEDs connected to the AR8327 switch
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4743/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39361
2014-01-21 17:17:42 +00:00
Gabor Juhos
506b40b628 ar71xx: tl-wr1043nd-v2: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39346
2014-01-20 10:23:06 +00:00
Gabor Juhos
c17cfab560 ar71xx: tl-wdr4300: define LEDs connected to the AR8327 switch
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39345
2014-01-20 10:23:05 +00:00
Gabor Juhos
db5f22a2d7 ar71xx: set default LED config for the RB2011* boards
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 39344
2014-01-20 10:23:04 +00:00