CS-QR10 is MT7620A based IP Camera.
the camera and sound does not work with kernel 4.4.
- camera chip is sn9c291.
- sound chip is wm8960.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 49234
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.
v1->v2:
* Remove some references to 2626 that I had missed in the dts.
v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 49213
ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.
it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
This patch adds support for GL-MT750.
GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps.
It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support.
SVN-Revision: 48994
This patch adds support for GL-MT300N.
GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM,
2 LANs, USB, UART, GPIO and PoE support.
SVN-Revision: 48993
This patches adds support for GL-MT300A.
GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM,
Two LANs, USB, UART and MMC daughter board.
SVN-Revision: 48992
add support for Planex MZK-WDPR.
MZK-WDPR(MZK-WDPR-R01) is internet radio tuner.
This patch is "network board" in MZK-WDPR.
LCD board is non OpenWrt Platform.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 48968
This patch adds support for JHR-N805R, JHR-N825R and JHR-N926R to
various scripts in the base-files directory.
Signed-off-by: Reinhard Max <reinhard@m4x.de>
Reviewed-by: Torsten Duwe <duwe@lst.de>
SVN-Revision: 48905
Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026")
incorrectly changed the mode of the ramips shell scripts from 755 to 644.
I.e., they are not excutable any more and for example devices will be left
with broken configs.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
SVN-Revision: 48893
This patch adds support for Phicomm PSG1208.This is a router with MT7620A SoC with 8M flash and 64M ram.
The WPS led is uesd as status_led because the power light can't be controlled with GPIO.
It seems that the 5g wifi led is connected to MT7612E and it can't be controlled with GPIO too.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
SVN-Revision: 48721
This patch adds support for the Netgear EX2700 and builds an approriate
sysupgrade image.
What's missing is the option to build a factory image flashable via the
router's stock web interface, but this approach is hindered by the fact
that u-boot operforms an additional integrity check, which expects a
uImage header in the last 64 bytes of the "kernel" partition, which
the bootloader expects to be 960k, a size exceeded by the standard
OpenWrt kernel.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
SVN-Revision: 48698
This router is based on MT7621 SoC, no wifi, no usb, nand.
Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.
Doesn't work:
* No GPIO leds. All leds are controlled by switch,
but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
nand/spi drivers do not support pin sharing,
so it is not accessable and disabled. Stock
firmware could read it and it was empty.
* PoE out.
Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.
U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.
Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47881
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.
This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.
Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>
SVN-Revision: 47845
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617
Add support for Dovado tiny AC wifi router.
Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports
5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.
Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>
SVN-Revision: 47348
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.
The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.
v3 fix
1: Fixed model order
2: Remove manufacturer name from model name
3: Use a hacky but prettier way to get mac address.
Signed-off-by: Xiaoning Kang <kangxn@163.com>
SVN-Revision: 47111
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
SVN-Revision: 46921
This patch add support for Planex DB-WRT01. DANBOARD route on
the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
DANBOARD is Cartoon character.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46918
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46629
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46628
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
* changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
* changes filenames of dts and profile files
* changes image filenames
for Olimex RT5350F-OLinuXino{,-EVB} devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46623
The following patch changes:
* board name from "wl341v3" to "wl-341v3"
* dts filename
* LED names in dts file
for Sitecom WL-341v3 device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46622
The following patch:
* changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
* changes filenames of dts and profile
* fixes LED names in dts file and base-files scripts
* removes manufacturer name from image filename
for Xiaomi MiWiFi Mini device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46617
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46614
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs
Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)
More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46454
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
SVN-Revision: 46405
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.
Signed-off-by: Tom Deng <2579131212@qq.com>
SVN-Revision: 46349
This patch adds support for the Linksys RE6500 Range Extender
http://wiki.openwrt.org/toh/linksys/re6500
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46043
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.
Signed-off-by: tymon <banglang.huang@foxmail.com>
SVN-Revision: 46041
Version 2 : White spaces and alphabetical order problems
fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware
Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>
SVN-Revision: 45902
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
(Reposted due to an issue with the patchwork server during original submission)
Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)
Signed-off-by: Gareth Bryan <gareth@mx9.org>
SVN-Revision: 43102
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.
Signed-off-by: Ron Curry <wingspinner@gmail.com>
SVN-Revision: 42785
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.
Signed-off-by: Lintel <lintel.huang@gmail.com>
SVN-Revision: 41961
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 41939
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)
http://wiki.openwrt.org/toh/kingston/mlw221
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 41841
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken. This seems to fix it.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 41837
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 40908
Hi Hartmut,
Thanks for your feedback, I have reformated the patch accordingly.
Added support for Teltonika RUT5XX hardware.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
SVN-Revision: 40907
The 7Links PX-4885 is a small battery-powered wireless router.
It is based on a RT5350F WiSoC and features one ethernet port and one
USB port. It is a Hame MPR-A1 clone, except it has different GPIOs,
a different battery and more RAM (32 MB).
This patch adds a profile for this board, the corresponding device tree
file and the adequate base-files changes (incl. sysupgrade).
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
SVN-Revision: 40554
The rt2x00 wifi driver may still need updating to
function with this device.
Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>
SVN-Revision: 39298
added dts file and userspace scripts modified to support Asus RT-N14U board
current support status:
usb works
ethernet works
buttons reset, wps
leds asus:blue:[usb|lan|wan|air|power]
i2c not tested
uart not tested
wifi not yet
Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>
SVN-Revision: 39163
HG255D is a kind of popular low-end home gateway in China, this patch bring the the trunk support for it. It is adapted from a local Chinese community (www.right.com.cn), so credit should given to them.
This patch is tested to work except trivial LED issues.
Signed-off-by: Leon Xu <ylxu72@gmail.com>
SVN-Revision: 37505
This patch adds support for HAME MPR-A2 router using a DTS file.
The platform is Ralink RT5350.
http://wiki.openwrt.org/toh/hame/mpr-a2
Signed-off-by: Dmitry Shmygov <shmygov@rambler.ru>
SVN-Revision: 36898
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36435
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36433
Add Netgear WNCE2001.
This is a small RT3052 device with 4MB spi flash and 32MB ram.
2 built-in antennas, 1x fastE, no USB, reset & wps switch.
On my model the AP/RT switch is unpopulated, but I verified the gpio
mapping for it.
The stock firmware is running an unprotected tftpd which allows you
to read any file from the filesystem.
Serial port is present on testpads (See image on the wiki page).
There are more testpads below the shield near the SoC, which
may have JTAG.
Slight annoyance: The bootloader is checksumming kernel&rootfs, but
can be tricked by zeroing checksum and length fields in the checksum
partition, see
target/linux/ramips/base-files/lib/preinit/04_disable_wnce2001_flash_checksumming
The manufacturer image is very similar to the DAP one, so I slightly
modified mkdapimg to support generating it.
The resulting
openwrt-ramips-rt305x-wnce2001-squashfs-factory-(worldwide|northamerica).bin
can be used to flash from stock to OpenWRT using the stock firmware
upgrade function, without using the serial port.
http://www.netgear.com/landing/wnce2001.aspxhttp://wiki.openwrt.org/toh/netgear/wnce2001
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 36289
This patch introduces OpenWRT support for the base Hauppauge/PCTV Broadway
platform. It doesn't deal with the TV tuner or transcoder at this point,
but the core functionality is working (Ethernet, wireless, USB, buttons,
LEDs, etc).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
SVN-Revision: 34595
Commit 7c8edac25f23c4fc14239fdc293caa1317649944 introduced new machine and
Makefile changes to build images for this target. However, without the userspace
bits a ramips machine can't use wifi as the necessary "eeprom" data is to be
extracted by a hotplug script; also, sysupgrade support and default led
configuration are missing.
An IRC user reported these changes allowed him to use wifi on his hardware.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 34331
Add support for 8devices Carambola dev board.
The Carambola is a small RT3050-based development board with two
ethernet ports, on-board chip antenna, usb and plenty of accessible
gpio ports, sold by 8devices.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 33303
Generate image for the ALL0239-3G which can be flashed through the
chipset-vendor SDK based firmware's web-interface and bootloader.
The bootloader seems to ignore uImage checksum errors, but does complain about
them once the 0xDEADC0DE was replaced by an actual JFFS2 page.
I'm working on implementing fixtrx for uImage in the mtd package to solve this.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33206
rt2x00 still needs some patching as the radio doesn't come to life.
Installation via webflash.
[juhosg: fix whitespace issues, remove rt305x_register_usb
from machine setup because the board has no USB port]
Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi>
SVN-Revision: 33205
Full functionality runtime tested, installation via OEM web-interface requires
a follow-up patch.
Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing
bits (including the antiparallel wps led).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
SVN-Revision: 33142
The initial support for the D-Link DAP-1350.
USB related functionality is not tested.
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 32821
This patch adds support for the Korean made Petatel PSR-680W Wireless CDMA Router.
The platform is based on Ralink RT3052.
http://wiki.openwrt.org/toh/petatel/psr-680w
Signed-off-by: Dmitry Shmygov <shmygov at rambler.ru>
SVN-Revision: 32450
Sysupgrade works just fine on my Sitecom WL-351 after adding this
oneliner.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 31843
More device info at: http://wiki.openwrt.org/toh/tenda/w306r
Signed-off-by: David Pearce <David_18051985@hotmail.com.au>
[juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages
from the profile, change broken GPIO number]
SVN-Revision: 31396
[juhosg: fix indentation in platform scripts, and remove debug
messages from 06_set_iface_mac]
Signed-off-by: Patrick van Staveren <trick@vanstaveren.us>
SVN-Revision: 30808
This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19.
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
SVN-Revision: 28571
