Commit graph

25 commits

Author SHA1 Message Date
Sven Eckelmann
1330ff189b ar71xx: extract ath10k wifi board.bin for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Henryk Heisig
e39dc8d823 ar71xx: add support to TP-Link Archer C59v1 and C60v1
TP-Link Archer C59v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- 8x LED (controled by 74HC595), 3x button
- UART header on PCB

TP-Link Archer C60v1 is a dual-band AC1350 router, based on Qualcomm/Atheros
QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Currently not working:
- Port LAN1 on C59, LAN4 on C60
- WiFi 5GHz (missing ath10k firmware for QCA9886 chip)
- Update from oficial web interface ( tplink-saveloader not support "product-info")

Flash instruction:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-cXX-v1-squashfs-factory.bin
and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:

1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[Jo-Philipp Wich: remove duplicate ATH79_MACH_ARCHER_C59/C60_V1 entries]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2017-01-26 11:38:21 +01:00
Tal Keren
9c475eca3e ar71xx: add support for TP-Link RE450
Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.

The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)

The result factory image is flashable from the stock web ui.

Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2016-12-22 14:50:05 +01:00
Radek Dostál
236fc232bb ar71xx: sort items in 11-ath10k-caldata alphabetically
Requested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
2016-12-22 14:50:05 +01:00
Piotr Dymacz
c198ca682c ar71xx: add support for YunCore SR3200 and XD3200
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.

YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.

Common specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm

SR3200 specification:

- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB

XD3200 specification:

- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB

LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.

Flash instruction under vendor firmware, using telnet/SSH:

1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware

Flash instruction under U-Boot, using UART:

1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-12 09:57:40 +01:00
Piotr Dymacz
16afa08d19 ar71xx: add support for COMFAST CF-E380AC v1 and v2
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.

There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size

Version number is available only inside vendor GUI,
hardware and markings are the same.

Short specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-11-21 10:05:40 +01:00
Henryk Heisig
0d760bfba8 ar71xx: tl-wpa8630: Use dynamic parsing of the firmware partition
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-16 11:01:18 +01:00
Henryk Heisig
1b2b3cb8be ar71xx: wpa8630: change board name to tl-wpa8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-11-08 11:17:10 +01:00
Henryk Heisig
8cc0c34ef5 ar71xx: Add support to Powerline ac TP-Link WPA8630
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
2016-10-31 17:13:37 +01:00
Stijn Tintel
e3875350f3 ar71xx: add support for D-Link DAP-2695 rev. A1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
2016-10-27 01:50:42 +03:00
Jing Lin
7ba9a3a504 ar71xx: Add support to DomyWifi DW33D
Signed-off-by: Jing Lin <mumuqz@163.com>
2016-10-25 17:51:08 +02:00
Florian Beier
5abeba3450
ar71xx: add userspace support for D-Link DIR-869 A1, generate images
Signed-off-by: Florian Beier <beier.florian@gmail.com>
[Matthias Schiffer: fix factory image, improve commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2016-10-11 22:58:37 +02:00
Sven Eckelmann
c4e3706533 ar71xx: extract ath10k wifi board.bin for the OpenMesh MR1750v2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2016-05-23 12:19:26 +02:00
P.Wassi
8307c2fe68 ar71xx: Add support for Ubiquiti UniFi AP AC PRO
Add support for the Ubiquiti UniFi AP AC PRO
Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
P.Wassi
c855e70491 ar71xx: Rename unifiac to unifiac-lite
To avoid confusion with different unifiac devices, rename existing target
"unifiac" to "unifiac-lite", before "unifiac-pro" is introduced.

Signed-off-by: P.Wassi <p.wassi at gmx.at>
2016-05-12 03:29:36 +02:00
John Crispin
063a6499db ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-ACv2 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49154
2016-04-09 10:26:31 +00:00
John Crispin
0c0dc3b2bf ar71xx: extract ath10k wifi board.bin for the OpenMesh OM5P-AC board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>

SVN-Revision: 49147
2016-04-09 10:26:08 +00:00
John Crispin
cede06cebc ar71xx: Support for Ubiquiti UniFi AP AC LITE
Add support for the Ubiquiti UniFi AP AC LITE
Signed-off-by: P.Wassi <p.wassi at gmx.at>

SVN-Revision: 48711
2016-02-12 08:31:32 +00:00
Felix Fietkau
ae7e7239b8 ar71xx: Add support for ZyXEL NBG6616.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>

SVN-Revision: 47405
2015-11-07 12:51:39 +00:00
John Crispin
bfeae90850 ar71xx: extract ath10k wifi board.bin for the OpenMesh MR1750 board
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>

SVN-Revision: 46933
2015-09-14 20:12:00 +00:00
John Crispin
af60c367b7 ar71xx: add support for TP-Link TL-WDR6500 v2
Signed-off-by: Weijie Gao <hackpascal@gmail.com>

This patch adds support for TP-Link TL-WDR6500 v2.

The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for
the whole firmware, so I have to create a new firmware creation method.

SVN-Revision: 46663
2015-08-17 06:24:04 +00:00
John Crispin
c89f360059 ar71xx: Enable ath10k calibration data loading for EnGenius ESR1750 and EPG500.
As r46245 disabled the board.bin template workaround, 5GHz wifi stopped working
on these devices. This adds them to the calibration data loading introduced in
r46244 and thus makes 5GHz work again for these devices.

Signed-off-by: Christian Beier <cb@shoutrlabs.com>

SVN-Revision: 46415
2015-07-18 21:15:42 +00:00
John Crispin
1eccdb4fd4 ar71xx: add support for the devolo dLAN pro 1200+ WiFi ac
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>

SVN-Revision: 46342
2015-07-14 07:37:03 +00:00
John Crispin
f3bdc4a76a ar71xx: Unify ath10k calibration data loading
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.

This patch makes all boards use the first method.

Signed-off-by: Matti Laakso <malaakso@elisanet.fi>

SVN-Revision: 46244
2015-07-07 13:47:57 +00:00
Gabor Juhos
0bd06aca20 ar71xx: add user-space support for RB911G-5HPacD
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 45300
2015-04-07 20:04:14 +00:00