ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Signed-off-by: daixj <fl.service@t-firefly.com>
SVN-Revision: 44690
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
SVN-Revision: 44469
the old FE_INT_STATUS register becomes two registers.
FE_INT_STATUS and INT_STATUS. so the hw status almost full
must change to read from FE_INT_STATUS register.
tx/rx done read from INT_STATUS register.
mt7620 datasheet define CNT_GDM1_AF at BIT(29).
but after test it should be BIT(13). why?
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44371
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 44356
This patch sets the correct location of the mt76 radio in the pcie bridge
(pcie-bridge instead of pcie0). Additionaly, it disables the 2.4 GHz band.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44355
Both Y1 and Y1S have MT7612E wireless chip so I submitted this patch.
Tested on Lenovo Y1.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 44354
The ubootloader of the M2M sets the reset bits for
both USB device and USB host during initialization
(to save a few mA of power during boot).
However, for the usb<->sata bridge to be properly
detected, it is necessary to clear both reset bits
as otherwise the kernel logs will just be filled
with:
usb 1-1: device descriptor read/64, error -145
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44248
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
- budget is decremented with completed frames, so don't check if done is
smaller
- ACK the interrupt before processing further frames to fix a small race
condition.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44234
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Signed-off-by: wengbj <linux.c@foxmail.com>
SVN-Revision: 44166
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
* use default timeout value
* print more debug ring info
* move timeout reset function to workqueue
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44043
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This patch fixes a wrong mask operation for the rt2880-compatible ralink devices.
The mask operation reads the actual flags and then logical combines it with the pin flag it want to set.
Unfortunally, for rising as for falling interrupt flags the actual flag status of the rising interrupts was used.
That caused a problem if you want to use more than one falling GPIO interrupt.
Now the correct (seperated) actual status is used for both, falling and rising.
Signed-off-by: Jonas Arndt <info@greenwire-elektronik.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43882
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
