- only sunxi has this disabled
- unify kernel configuration across platforms
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46307
commit r46299 broke the mvebu target because one patch does not apply
any more. This commit closes#20070.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46303
In fb6f62e97733312053ab593fcf68eea47a21169e several settings
are set on the ethernet device, but they are not working.
Fix Ethernet by setting the right values.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
SVN-Revision: 46281
no-op since 2.6.35
removed in Kernel 4.1
see https://lwn.net/Articles/380931/
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 46280
This patch adds the RFKill GPIO control switch and enables another GPIO to
control power supply to USB Ports by emulating an LED GPIO for WDR4900v1.
Signed-off-by: Guo Wei Lim <alphasparc@gmail.com>
SVN-Revision: 46279
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
The mips reloc patch introduced new allocations which were done before
add_unformed_module but never freed them in case of an error. A new hook in
Linux 3.19 called module_arch_freeing_init can be used for freeing memory
which were allocated during this init phase.
The problem can be seen when trying to load a module (via busybox insmod)
when it was already loaded.
free -m
for i in `seq 1 100`; do
/sbin/insmod /lib/modules/*/ath9k.ko >& /dev/null
done
free -m
This simple loop would leak ~3.2 MB.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46247
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
This device is identical to the TL-WR740N v5, it even uses the same HWID (which
wasn't the case for older TL-WR741ND revisions).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46238
Backport for the Spansion S25FL164K
It's a 8 MiB flash chip with 4 KiB erase sectors.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46237
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
Add features ext4 targz to target x86/xen_domu in order to
generate images in defconfig.
This fixes#18074.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 46233
Basically the only error I am seeing is "Correctable Error". Also newer
lantiq PCIe drivers have this message wrapped in a "if debug enabled"
block. So it should be safe to disable this warning.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46222
Newer DSL driver versions depend on the address information.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46221
This is useful if the device also has an ethernet WAN interface with a
separate mac address (that is derived from the LAN mac address).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46220
Make it consistent with the net_device struct and the xrx200 driver
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46219
All (still relevant) patches were refresh.
The following patches were dropped because they are applied upstream:
- 0003-MIPS-lantiq-handle-vmmc-memory-reservation.patch
- 0005-MIPS-lantiq-add-reset-controller-api-support.patch
- 0006-MIPS-lantiq-reboot-gphy-on-restart.patch
- 0009-MIPS-lantiq-command-line-work-around.patch
- 0010-MIPS-lantiq-export-soc-type.patch
- 0011-lantiq-add-support-for-xrx200-firmware-depending-on-.patch
- 0037-MIPS-lantiq-move-eiu-init-after-irq_domain-register.patch
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46216
The initialization routines for these boards were relying on some (wrong)
defaults for the QCA953x ethernet. Make these defaults explicit to prevent
breaking them when the QCA953x defaults are fixed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46206
