Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
Using the JSON output option depends on json library so
add select json-c library when JSON output is selected.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47928
- 1.4.x has IPv6 support
- set C std explicitly due to gcc 5 changes/old code style of dante
- disable pam via configure vars since detection of without pam option
is broken (-lpam gets linked in if available)
- remove and refresh patches
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47926
- tested on Beagleboard C4
- remove upstream patches
- disable THUMB mode on OMAP3 this increases binary size
(remove CONFIG_SYS_THUMB_BUILD)
- reduce SPL size by disabling EXT feature
(remove CONFIG_SPL_EXT_SUPPORT)
this fixes 2015.07 and 2015.10-rc3
Beagleboard C4 booting
which were broken by upstream commit
with id: bd2c4522c26d535515aebca52d27c004a7e0c05c
Arm THUMB mode is broken because of an yet unknown errata
see: http://lists.denx.de/pipermail/u-boot/2015-August/225793.html
- backport upstream fix that was introduced in 2015.10-rc5
and was not fixed in 2015.10 final
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47924
since Kernel 3.14
408eccce net: ptp: move PTP classifier in its own file
found while bug search
thx olmari on IRC
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47923
Principal purpose is to prevent the error message
ifxmips_ptm_vdsl.c:281:ptm_hard_start_xmit: not in showtime
which is printed at least once per second to the serial console, if the
ptm interface is not in showtime, but a processes already sends
packages over that interface. This happens for adsl as well as vdsl
over ptm.
It's pppd which sends packages over the ptm device before in showtime.
As far as I can see, pppd is started unconditionally since netif can
not gather the link status of the ptm network interface.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47917
This prevents the unconditionally start of pppd since netifd will be
triggered if the device goes into showtime. The same applies to lost
showtime as well.
In compare to the ptm driver, this changeset isn't strictly required,
since the "not in showtime" message is limited to the debug loglevel.
But it reduces the amount of ppp related messages significant.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47916
- CONFIG_IFX_CLI is unused, couldn't find any reference to this config variable
- use disable-feature instead of enable-feature=no
- reorder configure args to have depending args together
- remove configure args which set the default value
- group enable-model and configure args which enable or disable features that
are covered by the feature set
The config.log contains the same values as before. The vdsl_cpe_control binary
has the same checksum as before.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47888
The typicial feature set doesn't include "DSL PM showtime counters support"
(INCLUDE_DSL_CPE_PM_SHOWTIME_COUNTERS). This feature provides the
vdsl_cpe_control command 'pmccsg', which is used by 'dsl_control status' to get
the line uptime.
The binary size increases to 103912 byte (+4256 byte) uncompressed.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47887
Add 'platform_nand_pre_upgrade' callback to allow platform specific
preparation right before flashinng, when already in ramdisk.
Example uses might be setting correct values for CI_{KERNPART,UBIPART}.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
SVN-Revision: 47879
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
OpenSSL moves old versions of the library from
http://www.openssl.org/source/ to
http://www.openssl.org/source/old/$version/ breaking the old links.
That behavior breaks the OpenWRT-build every time OpenSSL releases
a new version.
This patch adds http://www.openssl.org/source/old/$version/ to the
PKG_SOURCE_URL of OpenSSL to avoid breaking the build whenever
OpenSSL releases a new version.
Signed-off-by: Kevin Kirsch <ranlvor@starletp9.de>
Reviewed-by: Alexander Dahl <post@lespocky.de>
SVN-Revision: 47860
Add the option "--all-servers" which forces dnsmasq to send all
queries to all servers and then take the first answer.
Signed-off-by: Andréas Gustafsson <gurgalof@gmail.com>
SVN-Revision: 47857
LEDs which are controlled by a PWM need to use the supplied
max_brightness instead. Otherwise they might appear to be
very dim / broken.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47854
Packages using libncursesw can fail to build if both libncurses and libncursesw
are not installed. Currently the ncurses.h file is installed in "usr/include/ncursesw"
directory and includes other .h files in the "usr/include" directory incorrectly.
For example: Including <ncursesw/ncurses.h> fails due to these references. These build
changes will set the correct include paths within the developer includes.
Packages that expect ncurses.h (or curses.h) in the default "usr/include" path fail
even when expecting to build with libncursesw and will need to be fixed as well. However,
they cannot be fixed until this patch is applied.
Signed-off-by: Ted Hess <thess@kitschensync.net>
SVN-Revision: 47853
Useful when using sound players that can send to icecast, etc. without any sound device attached.
Signed-off-by: Ted Hess <thess@kitschensync.net>
SVN-Revision: 47852
Because of dsl-vrx200-firmware-xdsl-* there's no need anymore to
download a dsl firmware at runtime.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47851
this error was not visible until recent bump to
busybox 1.24.1 stable which introduced a warning message
when keyword 'local' is not used with a shell-function.
this does not change behavior and is a cosmetic cleanup.
fixes the following output:
root@box:~ ifup <interface>
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 362: not in a function
/sbin/ifup: local: line 1: not in a function
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47828
Since kernel 4.2, DRBG is the default crypto API RNG, replacing krng. As
DRBG is not enabled, there is no crypto API RNG available when running
kernel 4.2 or later. Because of this, IPsec SAs fail to install. In
strongSwan, this results in a vague error that is difficult to debug:
received netlink error: No such file or directory (2)
Solve this by adding DRBG to the kmod-crypto-rng package. As enabling
DRBG in the kernel config also enables the Jitterentropy RNG, include it
in kmod-crypto-rng instead of having it in a separate package.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47827
Bump ubus to current Git HEAD in order to:
* Fix a null pointer access when user ACLs are loaded into memory
* Fix wrong permission handling for uid=0, gid!=0 peers
* Fix return code for permission defined cases
* Fix socket error handling when the server connection dies
* Make ACL file path configurable
* Remove invalid usages of poll() when using a zero timeout
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47816
The "iw" utility expects the VHT80 to be specified as uppercase "80MHZ",
change the script to reflect that.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47814
This version and version 3.6.8 are fixing the following security problems:
* CVE-2015-7744
* CVE-2015-6925
The activation of SSLv3 support is needed for curl.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47791
This should ensure that lldpd is among the first processes to stop,
so that it has time to send the shutdown LLDPU to the other side,
before the network goes down.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47786
Support next to the non-HT/HT channel widths like HT20 or NOHT also VHT80
channels during the mesh join
iw dev mesh0 mesh join "meshnet" freq 5180 80MHz
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47782
Fix the id of NL80211_ATTR_WIPHY_ANTENNA_GAIN for antenna_gain command when
using compat-wireless 2015-10-26.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47778
r47288 updated to Busybox 1.24.1 but did not update the configuration.
The configuration is updated by running
cd config
../convert_menuconfig.pl .../build_dir/target-*/busybox-1.24.1
cd ..
./convert_defaults.pl < .../build_dir/target-*/busybox-1.24.1/.config > \
Config-defaults.in
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 47775
Use the 'typical' compile configuration instead of 'full', which most
notably excludes the soap support.
/sbin/vdsl_cpe_control shrinks down to ~50%, from 178kb(!) to 90kb.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47769
This adds support for specifying the dsl modem, atm bridge configs and setting
the pppoe protocol for wan.
These additions are required to port the Lantiq target to board.d.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47750
Some boards, e.g. the Sheeva Plug, require the lan interface to be set
to DHCP instead of a static address, therfore support that.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47732
This is a minor version update which fixes some small bugs. None of
these bugs were exploitable according to the release notes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47724
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
Remove support for now unused ucidef_add_switch_vlan(), move port->vlan and
vlan->interfaces conversion to uci-defaults-new.sh and massively simplify
config_generate.
This change prepares the following upcoming steps:
* Eliminate use of ucidef_set_interface_lan_wan() for switch only devices
* Merge ucidef_add_switch() with ucidef_add_switch_ports()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47719
Update dependencies for linux 4.4 and mark as broken where source code
needs updating.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 47700
Only se4t the force_link property for non-lan, non-wan ifaces as it is
unnecessary in the default cases.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47675
Properly quote variables in ucidef_set_interface_lan() and
ucidef_set_interface_lan(), otherwise interfaces with multiple devices
are not properly written into the configuration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47673
Add ucidef_set_board_id() and ucidef_set_model_name() procedures to store
model information in the board.json file.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47671
The only user was the hg255d board and config_generate did not even emit
proper uci for it.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47658
Remove extra nesting of rssi leds in the led object and move rssi monitor
declaration to its own object.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47655
This just renamed the package to indicate that this is the annex a version.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47649
Add support for generating vlans solely from the port layout description
given through ucidef_add_switch_ports().
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47639
Add further helper functions to uci-defaults-new.sh for easier declarations
of complex switch layouts.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47638
In this upstream dsl driver app version the autoboot is deactivated activate
it again.
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47637
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47635
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47634
This application helps to debug some internal problems in the MEI driver.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47632
This makes the build script use the same configure options as used by
Lantiq UGW and fixes some warnings and cleans up some of the patches.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47630
since r45833 and r45848 the overlayfs is automatically mounted read-only
(and blocks remounts as r/w) when JFFS2 is full. see ticket #19564
because of this normal file deletion is not possible anymore.
if a user logins interactively (e.g. SSH) show a hint for this,
that files must be removed in /overlay/upper/...
v2: fix subject line
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47623
The scripts for authsae and iw use the option mesh_id to get set the
"meshid" during a mesh join. But the script for wpad-mesh ignores the
option mesh_id and instead uses the option ssid. Unify the mesh
configuration and let the wpa_supplicant script also use the mesh_id from
the configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47615
The OpenWrt wireless configuration for mcast_rate is defined as Kbit/s when
using wpa_supplicant for IBSS/802.11s and iw for unencrypted IBSS/802.11s.
But when using authsae, the unit for the same option is redefined as
Mbit/s. Better use the same unit for this option independent of the backend
which is used.
Old values for mcast_rate (< 1000) are still interpreted Mbit/s to avoid
problems during upgrades from older versions.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47614
The variable $mesh_id was never defined in authsae_start_interface and thus
the option meshid in $authsae_conf_file was always set to "".
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47613
This version fixes a potential uncontrolled format string problem. This
makes it possible to activate the format security check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47600
This version fixes a potential uncontrolled format string problem. This
makes it possible to activate the format security check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47599
This version fixes a potential uncontrolled format string problem. This
makes it possible to activate the format security check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47598
If the user sets any preinit options in .config, the wrong path may get
applied due to wrong default value in image-config.in and due to Makefile
writing also the unchanged options into 00_preinit.conf
Modify the default path in image-config.in to match the current default
path set by r47080. Also modify the fall-back default in Makefile.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47590
I accidentally deactivated it. This should be set to active it in any case
independently what was set in the user config.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47587
All RTC drivers require the kernel to be built with CONFIG_RTC_CLASS=y.
Set it accordingly.
Tested only with DS1307.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47564
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
