Fix an upstream regression on 3.18+ that causes rt305x based devices
to hang on boot.
Fixes#19715.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45747
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)
Signed-off-by: Matteo Panella <m.panella@level28.org>
SVN-Revision: 45725
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port. The original product information can be found at:
http://www.aximcom.com/en/MR-102N
Signed-off-by: Tai-hwa Liang <atliang@gmail.com>
SVN-Revision: 45724
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45722
INET_LRO deprecated and there are exactly two drivers using it, neither
being included in any of the targets enabling INET_LRO. At the same time
both drivers needing it select it.
So just disable it for everyone.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45584
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Last time i got some mess . This is new version.
Signed-off-by: Jay Weng <fl.service@t-firefly.com>
SVN-Revision: 45018
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Signed-off-by: daixj <fl.service@t-firefly.com>
SVN-Revision: 44690
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
SVN-Revision: 44469
the old FE_INT_STATUS register becomes two registers.
FE_INT_STATUS and INT_STATUS. so the hw status almost full
must change to read from FE_INT_STATUS register.
tx/rx done read from INT_STATUS register.
mt7620 datasheet define CNT_GDM1_AF at BIT(29).
but after test it should be BIT(13). why?
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44371
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 44356
This patch sets the correct location of the mt76 radio in the pcie bridge
(pcie-bridge instead of pcie0). Additionaly, it disables the 2.4 GHz band.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44355
Both Y1 and Y1S have MT7612E wireless chip so I submitted this patch.
Tested on Lenovo Y1.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 44354
The ubootloader of the M2M sets the reset bits for
both USB device and USB host during initialization
(to save a few mA of power during boot).
However, for the usb<->sata bridge to be properly
detected, it is necessary to clear both reset bits
as otherwise the kernel logs will just be filled
with:
usb 1-1: device descriptor read/64, error -145
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44248
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
- budget is decremented with completed frames, so don't check if done is
smaller
- ACK the interrupt before processing further frames to fix a small race
condition.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44234
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Signed-off-by: wengbj <linux.c@foxmail.com>
SVN-Revision: 44166
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
* use default timeout value
* print more debug ring info
* move timeout reset function to workqueue
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44043
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.
The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]
Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44001
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43883
This patch fixes a wrong mask operation for the rt2880-compatible ralink devices.
The mask operation reads the actual flags and then logical combines it with the pin flag it want to set.
Unfortunally, for rising as for falling interrupt flags the actual flag status of the rising interrupts was used.
That caused a problem if you want to use more than one falling GPIO interrupt.
Now the correct (seperated) actual status is used for both, falling and rising.
Signed-off-by: Jonas Arndt <info@greenwire-elektronik.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43882
modules build during the kernel compile phase are ignored anyway,
all modules should be built using KernelPackage in
package/kernel/linux/modules/*
selecting the appropriate config symbols there rather than in
target/linux/*/config-*
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43842
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43715
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 43681
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43305
hardware status and tx vlan offload support on all targets
except rt5350. so i modify the IS_ENABLE condition only for
mt7621.
support mt7621 hardware status reference by SDK. but i don't
have mt7621. if not work just set mt7621 FE_REG_FE_COUNTER_BASE
to 0 to let software count.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43303
hardware tx vlan offload only support max 16 vids
now use add/delete vlan interface to update vlan id table
when duplicate vlan id index detect.
disable hardware tx vlan offload support.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 43301
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43292
the SDK does a bit of extra init that we did not do yet when using an external mt7530.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43245
* read MAC address from factory partition
* remove port defines since there is only one port (most likely C/P error)
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 43231
r43200 tries to detect if the fixup is needed or not. control the behaviour via
OF instead and disable unused ports.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43201
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 43153
some bootloaders (linksys e1700) set wonky hw trap values. reset this upon boot to make all ports work.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43117
