ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2. Specification: - SoC: MediaTek MT7628AN - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR - Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps) - USB: 1 x USB 2.0 port - Button: 1 x switch button, 1 x reset button - LED: 3 x LEDS (system power led is not GPIO controller) - UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND) Installation through Luci: - The original firmware is LEDE, so both LuCI or sysupgrade can be used. - Do not keep settings, for sysupgrade please use the -n option. Installation through bootloader webserver: - Plug power and hold reset button until red LED blink to bright. - Install sysupgrade image using web interface on 192.168.1.1. Signed-off-by: Kyson Lok <kysonlok@gmail.com> [match maximum image size with firmware partition] Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit is contained in:
parent
da472e5b30
commit
abbfcc8525
7 changed files with 155 additions and 0 deletions
|
@ -189,6 +189,9 @@ gl-mt300n|\
|
|||
gl-mt750)
|
||||
set_wifi_led "$board:wlan"
|
||||
;;
|
||||
gl-mt300n-v2)
|
||||
set_wifi_led "$board:red:wlan"
|
||||
;;
|
||||
hc5661|\
|
||||
hc5661a)
|
||||
ucidef_set_led_default "system" "system" "$board:blue:system" "1"
|
||||
|
|
|
@ -180,6 +180,10 @@ ramips_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
|
||||
;;
|
||||
gl-mt300n-v2)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan" "0:wan" "6@eth0"
|
||||
;;
|
||||
awapn2403)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0:lan" "1:wan" "6@eth0"
|
||||
|
|
|
@ -166,6 +166,9 @@ get_status_led() {
|
|||
miwifi-nano)
|
||||
status_led="$board:blue:status"
|
||||
;;
|
||||
gl-mt300n-v2)
|
||||
status_led="$board:red:wlan"
|
||||
;;
|
||||
m4-4M|\
|
||||
m4-8M)
|
||||
status_led="m4:blue:status"
|
||||
|
|
|
@ -217,6 +217,9 @@ ramips_board_detect() {
|
|||
*"GL-MT750")
|
||||
name="gl-mt750"
|
||||
;;
|
||||
*"GL-MT300N-V2")
|
||||
name="gl-mt300n-v2"
|
||||
;;
|
||||
*"HC5661")
|
||||
name="hc5661"
|
||||
;;
|
||||
|
|
|
@ -65,6 +65,7 @@ platform_check_image() {
|
|||
gl-mt300a|\
|
||||
gl-mt300n|\
|
||||
gl-mt750|\
|
||||
gl-mt300n-v2|\
|
||||
hc5*61|\
|
||||
hc5661a|\
|
||||
hg255d|\
|
||||
|
|
133
target/linux/ramips/dts/GL-MT300N-V2.dts
Normal file
133
target/linux/ramips/dts/GL-MT300N-V2.dts
Normal file
|
@ -0,0 +1,133 @@
|
|||
/dts-v1/;
|
||||
|
||||
#include "mt7628an.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/{
|
||||
compatible = "gl-inet,gl-mt300n-v2", "ralink,mt7620an-soc";
|
||||
model = "GL-MT300N-V2";
|
||||
|
||||
chosen {
|
||||
bootargs = "console=ttyS0,115200";
|
||||
};
|
||||
|
||||
memory@0 {
|
||||
device_type = "memory";
|
||||
reg = <0x0 0x8000000>;
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wan {
|
||||
label = "gl-mt300n-v2:blue:wan";
|
||||
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan {
|
||||
label = "gl-mt300n-v2:red:wlan";
|
||||
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys-polled";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
poll-interval = <20>;
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
BTN_0 {
|
||||
label = "BTN_0";
|
||||
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
};
|
||||
|
||||
BTN_1 {
|
||||
label = "BTN_1";
|
||||
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
usb {
|
||||
gpio-export,name = "usb";
|
||||
gpio-export,output = <1>;
|
||||
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
gpio {
|
||||
ralink,group = "wdt", "gpio", "wled_an", "p0led_an", "i2s";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
mtd-mac-address = <&factory 0x4000>;
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
ralink,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
m25p80@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <10000000>;
|
||||
m25p,chunked-io = <32>;
|
||||
|
||||
partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@30000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x30000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
factory: partition@40000 {
|
||||
label = "factory";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "firmware";
|
||||
reg = <0x50000 0xfb0000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
|
@ -26,6 +26,14 @@ define Device/miwifi-nano
|
|||
endef
|
||||
TARGET_DEVICES += miwifi-nano
|
||||
|
||||
define Device/gl-mt300n-v2
|
||||
DTS := GL-MT300N-V2
|
||||
IMAGE_SIZE := 16064k
|
||||
DEVICE_TITLE := GL-iNet GL-MT300N-V2
|
||||
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
||||
endef
|
||||
TARGET_DEVICES += gl-mt300n-v2
|
||||
|
||||
define Device/vocore2
|
||||
DTS := VOCORE2
|
||||
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
||||
|
|
Loading…
Reference in a new issue