openwrtv3/target/linux/kirkwood/image/Makefile

156 lines
4.3 KiB
Makefile
Raw Normal View History

#
# Copyright (C) 2009-2013 OpenWrt.org
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
KERNEL_LOADADDR:=0x8000
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL := kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SUFFIX := -uImage
KERNEL_IN_UBI := 1
PAGESIZE := 2048
SUBPAGESIZE := 512
BLOCKSIZE := 128k
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
IMAGE/factory.bin := append-ubi
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
endef
define Device/cisco_on100
DEVICE_TITLE := Cisco Systems ON100
DEVICE_DTS := kirkwood-on100
DEVICE_PACKAGES := kmod-i2c-mv64xxx
KERNEL_SIZE := 5376k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := on100
endef
TARGET_DEVICES += cisco_on100
define Device/cloudengines_pogoe02
DEVICE_TITLE := Cloud Engines Pogoplug E02
DEVICE_DTS := kirkwood-pogo_e02
BOARD_NAME := pogo_e02
SUPPORTED_DEVICES += pogo_e02
endef
TARGET_DEVICES += cloudengines_pogoe02
define Device/cloudengines_pogoplugv4
DEVICE_TITLE := Cloud Engines Pogoplug V4
DEVICE_DTS := kirkwood-pogoplug-series-4
DEVICE_PACKAGES := kmod-usb3
endef
TARGET_DEVICES += cloudengines_pogoplugv4
define Device/iom_iconnect-1.1
DEVICE_TITLE := Iomega Iconnect
DEVICE_DTS := kirkwood-iconnect
BOARD_NAME := iconnect
SUPPORTED_DEVICES += iconnect
endef
TARGET_DEVICES += iom_iconnect-1.1
kirkwood: add support for Iomega Storcenter ix2-200 Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-06 00:56:58 +00:00
define Device/iom_ix2_200
DEVICE_TITLE := Iomega StorCenter ix2-200
DEVICE_DTS := kirkwood-iomega_ix2_200
DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-i2c-mv64xxx kmod-hwmon-lm63
DEVICE_TYPE:=nas
PAGESIZE := 512
SUBPAGESIZE := 256
BLOCKSIZE := 16KiB
KERNEL_SIZE := 3072k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE_SIZE := 32505856
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE)
endef
TARGET_DEVICES += iom_ix2_200
define Device/linksys_audi
DEVICE_TITLE := Linksys EA3500 (Audi)
DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-basic kmod-gpio-button-hotplug
DEVICE_DTS := kirkwood-linksys-audi
KERNEL_SIZE := 2624k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := linksys-audi
SUPPORTED_DEVICES += linksys-audi
endef
TARGET_DEVICES += linksys_audi
define Device/linksys_viper
DEVICE_TITLE := Linksys E4200v2 / EA4500 (Viper)
DEVICE_PACKAGES := kmod-mwl8k swconfig wpad-basic kmod-gpio-button-hotplug
DEVICE_DTS := kirkwood-linksys-viper
KERNEL_SIZE := 2688k
KERNEL_IN_UBI := 0
UBINIZE_OPTS := -E 5
IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi
BOARD_NAME := linksys-viper
SUPPORTED_DEVICES += linksys-viper
endef
TARGET_DEVICES += linksys_viper
define Device/raidsonic_ib-nas62x0
DEVICE_TITLE := RaidSonic ICY BOX IB-NAS62x0
DEVICE_DTS := kirkwood-ib62x0
BOARD_NAME := ib62x0
SUPPORTED_DEVICES += ib62x0
endef
TARGET_DEVICES += raidsonic_ib-nas62x0
define Device/seagate_dockstar
DEVICE_DTS := kirkwood-dockstar
DEVICE_TITLE := Seagate FreeAgent Dockstar
BOARD_NAME := dockstar
SUPPORTED_DEVICES += dockstar
endef
TARGET_DEVICES += seagate_dockstar
define Device/seagate_goflexnet
DEVICE_TITLE := Seagate GoFlexNet
DEVICE_DTS := kirkwood-goflexnet
BOARD_NAME := goflexnet
SUPPORTED_DEVICES += goflexnet
endef
TARGET_DEVICES += seagate_goflexnet
define Device/seagate_goflexhome
DEVICE_TITLE := Seagate GoFlexHome
DEVICE_DTS := kirkwood-goflexhome
BOARD_NAME := goflexhome
SUPPORTED_DEVICES += goflexhome
endef
TARGET_DEVICES += seagate_goflexhome
define Device/zyxel_nsa310b
kirkwood: add ZyXEL NSA310b The ZyXEL NSA310 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1200Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: Realtek (over pcie) - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II port (1 internal and 1 external) - 2 USB 2.0 ports (1 front and 1 back) - Smart fan The stock u-boot cannot read ubi so it should be replaced with the LEDE/OpenWRT's u-boot or with a u-boot from here https://github.com/mibodhi/u-boot-kirkwood This device's boot ROM supports "kwboot" tool (in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared) that sends an uboot image to the board over serial connection, it is very easy to unbrick. The stock bootloader can use usb and read from FAT filesystems, so the installation process is simple, place the uboot file on a USB flashdrive formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL to the board and write the following commands in the bootloader console: usb reset fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin nand write 0x1000000 0x00000 0x100000 reset Now you are rebooting in the new u-boot, write this in its console to install the firmware: usb reset fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin nand erase.part ubi nand write 0x2000000 ubi 0x600000 If your firmware file is bigger than 6 MiBs you should write its size in hex instead of 0x600000 above, or remove that number entirely (it will take a while in this case). If you are using another uboot that can read ubi, set mtdparts like this mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi) And set your bootcmd to be like this bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 Then you can install the firmware as described above. After you installed (or configured) the u-boot for booting the firmware, write the device's mac address in the ethaddr u-boot env. The MAC address is usually on a sticker under the device (one of the two codes is the serial), it should begin with "107BEF" as it is assigned to ZyXEL. write in the u-boot console (use your MAC address instead of the example) setenv ethaddr 10:7B:EF:00:00:00 saveenv to save the mac address in the u-boot. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-01-23 19:34:29 +00:00
DEVICE_TITLE := ZyXEL NSA310b
DEVICE_DTS := kirkwood-nsa310b
DEVICE_PACKAGES := kmod-r8169 kmod-gpio-button-hotplug kmod-hwmon-lm85
BOARD_NAME := nsa310b
kirkwood: add ZyXEL NSA310b The ZyXEL NSA310 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1200Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: Realtek (over pcie) - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II port (1 internal and 1 external) - 2 USB 2.0 ports (1 front and 1 back) - Smart fan The stock u-boot cannot read ubi so it should be replaced with the LEDE/OpenWRT's u-boot or with a u-boot from here https://github.com/mibodhi/u-boot-kirkwood This device's boot ROM supports "kwboot" tool (in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared) that sends an uboot image to the board over serial connection, it is very easy to unbrick. The stock bootloader can use usb and read from FAT filesystems, so the installation process is simple, place the uboot file on a USB flashdrive formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL to the board and write the following commands in the bootloader console: usb reset fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin nand write 0x1000000 0x00000 0x100000 reset Now you are rebooting in the new u-boot, write this in its console to install the firmware: usb reset fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin nand erase.part ubi nand write 0x2000000 ubi 0x600000 If your firmware file is bigger than 6 MiBs you should write its size in hex instead of 0x600000 above, or remove that number entirely (it will take a while in this case). If you are using another uboot that can read ubi, set mtdparts like this mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi) And set your bootcmd to be like this bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 Then you can install the firmware as described above. After you installed (or configured) the u-boot for booting the firmware, write the device's mac address in the ethaddr u-boot env. The MAC address is usually on a sticker under the device (one of the two codes is the serial), it should begin with "107BEF" as it is assigned to ZyXEL. write in the u-boot console (use your MAC address instead of the example) setenv ethaddr 10:7B:EF:00:00:00 saveenv to save the mac address in the u-boot. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-01-23 19:34:29 +00:00
endef
TARGET_DEVICES += zyxel_nsa310b
kirkwood: add ZyXEL NSA310b The ZyXEL NSA310 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1200Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: Realtek (over pcie) - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II port (1 internal and 1 external) - 2 USB 2.0 ports (1 front and 1 back) - Smart fan The stock u-boot cannot read ubi so it should be replaced with the LEDE/OpenWRT's u-boot or with a u-boot from here https://github.com/mibodhi/u-boot-kirkwood This device's boot ROM supports "kwboot" tool (in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared) that sends an uboot image to the board over serial connection, it is very easy to unbrick. The stock bootloader can use usb and read from FAT filesystems, so the installation process is simple, place the uboot file on a USB flashdrive formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL to the board and write the following commands in the bootloader console: usb reset fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin nand write 0x1000000 0x00000 0x100000 reset Now you are rebooting in the new u-boot, write this in its console to install the firmware: usb reset fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin nand erase.part ubi nand write 0x2000000 ubi 0x600000 If your firmware file is bigger than 6 MiBs you should write its size in hex instead of 0x600000 above, or remove that number entirely (it will take a while in this case). If you are using another uboot that can read ubi, set mtdparts like this mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi) And set your bootcmd to be like this bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 Then you can install the firmware as described above. After you installed (or configured) the u-boot for booting the firmware, write the device's mac address in the ethaddr u-boot env. The MAC address is usually on a sticker under the device (one of the two codes is the serial), it should begin with "107BEF" as it is assigned to ZyXEL. write in the u-boot console (use your MAC address instead of the example) setenv ethaddr 10:7B:EF:00:00:00 saveenv to save the mac address in the u-boot. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-01-23 19:34:29 +00:00
define Device/zyxel_nsa325
DEVICE_TITLE := ZyXEL NSA325 (v1 and v2)
DEVICE_DTS := kirkwood-nsa325
DEVICE_PACKAGES := kmod-gpio-button-hotplug kmod-rtc-pcf8563 kmod-usb3
BOARD_NAME := nsa325
endef
TARGET_DEVICES += zyxel_nsa325
$(eval $(call BuildImage))