openwrtv3/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata

128 lines
2.9 KiB
Text
Raw Normal View History

#!/bin/sh
ath10kcal_die() {
echo "ath10cal: " "$*"
exit 1
}
ath10kcal_from_file() {
local source=$1
local offset=$2
local count=$3
dd if=$source of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $source"
}
ath10kcal_extract() {
local part=$1
local offset=$2
local count=$3
local mtd
mtd=$(find_mtd_chardev $part)
[ -n "$mtd" ] || \
ath10kcal_die "no mtd device found for partition $part"
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
ath10kcal_die "failed to extract calibration data from $mtd"
}
ath10kcal_patch_mac() {
local mac=$1
[ -z "$mac" ] && return
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=6 count=6
}
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/ar71xx.sh
. /lib/functions.sh
. /lib/functions/system.sh
board=$(ar71xx_board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
cf-e380ac-v1|\
cf-e380ac-v2|\
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
dlan-pro-1200-ac|\
sr3200|\
xd3200)
ath10kcal_extract "art" 20480 2116
;;
dap-2695-a1)
ath10kcal_extract "radiocfg" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
;;
dw33d)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_binary art 18)
;;
mc-mac1200r)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -1)
;;
tl-wdr6500-v2)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)
;;
r6100)
ath10kcal_extract "caldata" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) +2)
;;
dir-869-a1 | \
qihoo-c301)
ath10kcal_extract "radiocfg" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
;;
esr1750 | \
epg5000)
ath10kcal_extract "caldata" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
mr1750 | \
mr1750v2 | \
om5p-acv2)
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
tl-wpa8630)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
unifiac-lite | \
unifiac-pro)
ath10kcal_extract "EEPROM" 20480 2116
;;
esac
;;
"ath10k/cal-pci-0000:01:00.0.bin")
case $board in
archer-c5 | \
archer-c7)
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)
;;
nbg6616 | \
nbg6716)
ath10kcal_extract "RFdata" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth1/address) -2)
;;
rb-911g-5hpacd)
ath10kcal_from_file "/sys/firmware/routerboot/ext_wlan_data" 20480 2116
;;
om5p-ac)
ath10kcal_extract "ART" 20480 2116
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
esac
;;
*)
exit 1
;;
esac