openwrtv4/target/linux/sunxi/patches-3.14/232-1-dt-sun7i-add-wifi-to-cubietruck.patch
Zoltan Herpai f10f009609 sunxi: initial 3.14 patchset
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>

SVN-Revision: 42313
2014-08-27 12:09:46 +00:00

96 lines
2.5 KiB
Diff

From 3e7fc7d394db0783996519f2d5affde5152a628e Mon Sep 17 00:00:00 2001
From: Chen-Yu Tsai <wens@csie.org>
Date: Thu, 26 Dec 2013 17:14:33 +0800
Subject: [PATCH] ARM: dts: sun7i: add WiFi module to Cubietruck DTS
The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The WiFi
part is a BCM43362 IC connected to MMC2 in the A20 SoC via SDIO.
The IC also takes a 32.768 KHz low power clock input, and a power
enable signal via GPIO.
The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not supported in this patch.
---
arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 47 ++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
index 66bb3ef..2444806 100644
--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
@@ -28,6 +28,23 @@
status = "okay";
};
+ mmc3: mmc@01c12000 {
+ pinctrl-names = "default", "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ pinctrl-1 = <&wifi_host_wake_pin>;
+ vmmc-supply = <&reg_vmmc3>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf@0 {
+ /* out of band interrupt not working */
+ /* compatible = "broadcom,bcm43362"; */
+ interrupt-parent = <&pio>;
+ interrupts = <10 2>; /* EINT10 */
+ status = "okay";
+ };
+ };
+
usbphy: phy@01c13400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
@@ -56,6 +73,18 @@
};
pinctrl@01c20800 {
+ mmc3_pins_a: mmc3@0 {
+ /* AP6210 requires pull-up */
+ allwinner,pull = <1>;
+ };
+
+ vmmc3_pin_cubietruck: vmmc3_pin@0 {
+ allwinner,pins = "PH9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 {
allwinner,pins = "PH12";
allwinner,function = "gpio_out";
@@ -69,6 +98,13 @@
allwinner,drive = <0>;
allwinner,pull = <0>;
};
+
+ wifi_host_wake_pin: wifi_host_wake_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
};
uart0: serial@01c28000 {
@@ -147,4 +183,15 @@
reg_usb2_vbus: usb2-vbus {
status = "okay";
};
+
+ reg_vmmc3: vmmc3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vmmc3_pin_cubietruck>;
+ regulator-name = "vmmc3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 7 9 0>;
+ };
};
--
2.0.3