KumiSystems/openwrtv4
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity
openwrtv4/target/linux/ipq806x/image/Makefile
Sven Eckelmann 86e18f6706 ipq806x: add support for OpenMesh A42 
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
  - 802.3af POE on Ethernet 1
  - 18-24v passive POE (mode B) on Ethernet 2

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2018-01-13 08:00:14 +01:00

324 lines
9.5 KiB
Makefile
Raw Blame History

# Copyright (c) 2014 The Linux Foundation. All rights reserved.
#
include $(TOPDIR)/rules.mk
include $(INCLUDE_DIR)/image.mk
UBIFS_OPTS = -m 2048 -e 124KiB -c 4096 -U -F
define Image/Prepare
$(CP) $(LINUX_DIR)/vmlinux $(KDIR)/vmlinux-unstripped.elf
endef
define Image/BuildKernel
$(CP) $(KDIR)/vmlinux-unstripped.elf $(BIN_DIR)/$(IMG_PREFIX)-vmlinux.elf
endef
define Image/Build/squashfs
cp $(KDIR)/root.squashfs $(KDIR)/root.squashfs-raw
$(call prepare_generic_squashfs,$(KDIR)/root.squashfs)
endef
define Image/Build
$(call Image/Build/$(1),$(1))
dd if=$(KDIR)/root.$(1) of=$(BIN_DIR)/$(IMG_PREFIX)-$(1)-root.img bs=2k conv=sync
endef
define Device/Default
PROFILES := Default
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs
KERNEL_PREFIX := $$(IMAGE_PREFIX)
KERNEL_LOADADDR = 0x42208000
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
IMAGE/sysupgrade.tar = sysupgrade-tar | append-metadata
endef
define Device/LegacyImage
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
endef
define Device/FitImage
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/FitImageLzma
KERNEL_SUFFIX := -fit-uImage.itb
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb
KERNEL_NAME := Image
endef
define Device/UbiFit
KERNEL_IN_UBI := 1
IMAGES := nand-factory.ubi nand-sysupgrade.tar
IMAGE/nand-factory.ubi := append-ubi
IMAGE/nand-sysupgrade.tar := sysupgrade-tar | append-metadata
endef
define Device/DniImage
PROFILES += $$(DEVICE_NAME)
FILESYSTEMS := squashfs
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
NETGEAR_BOARD_ID :=
NETGEAR_HW_ID :=
UBINIZE_OPTS := -E 5
IMAGES := factory.img sysupgrade.tar
IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakeroot-hdr | pad-to $$$$(KERNEL_SIZE) | append-ubi | netgear-dni
IMAGE/sysupgrade.tar := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-uImage-fakeroot-hdr | sysupgrade-tar kernel=$$$$@ | append-metadata
endef
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
define Device/TpSafeImage
PROFILES += $$(DEVICE_NAME)
FILESYSTEMS := squashfs
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
TPLINK_BOARD_ID :=
IMAGES := factory.bin sysupgrade.bin
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory
IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | append-metadata
endef
DEVICE_VARS += TPLINK_BOARD_ID
define Device/ZyXELImage
PROFILES += $$(DEVICE_NAME)
FILESYSTEMS := squashfs
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $${KERNEL_SIZE}
KERNEL_NAME := zImage
IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ | append-metadata
IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE}
IMAGE/mmcblk0p4-kernel.bin := append-kernel
endef
define Device/avm_fritzbox-4040
$(call Device/FitImageLzma)
DEVICE_DTS := qcom-ipq4019-fritz4040
KERNEL_LOADADDR := 0x80208000
BLOCKSIZE := 4k
PAGESIZE := 256
BOARD_NAME := fritz4040
DEVICE_TITLE := AVM Fritz!Box 4040
IMAGE_SIZE := 29753344
IMAGES = sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := kmod-usb-phy-qcom-ipq4019 ipq-wifi-fritz4040 fritz-tffs fritz-caldata u-boot-fritz4040
endef
TARGET_DEVICES += avm_fritzbox-4040
define Device/linksys_ea8500
$(call Device/LegacyImage)
DEVICE_DTS := qcom-ipq8064-ea8500
PAGESIZE := 2048
BLOCKSIZE := 128k
KERNEL_SIZE := 3072k
FILESYSTEMS := squashfs
KERNEL = kernel-bin | append-dtb | uImage none | append-uImage-fakeroot-hdr
PROFILES += $$(DEVICE_NAME)
BOARD_NAME := ea8500
SUPPORTED_DEVICES += ea8500
UBINIZE_OPTS := -E 5
IMAGES := factory.bin sysupgrade.tar
IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi
DEVICE_TITLE := Linksys EA8500
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += linksys_ea8500
define Device/netgear_d7800
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-d7800
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := D7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := d7800
SUPPORTED_DEVICES += d7800
DEVICE_TITLE := Netgear Nighthawk X4 D7800
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += netgear_d7800
define Device/netgear_r7500
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-r7500
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7500
NETGEAR_HW_ID := 29764841+0+128+256+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500
SUPPORTED_DEVICES += r7500
DEVICE_TITLE := Netgear Nighthawk X4 R7500
DEVICE_PACKAGES := ath10k-firmware-qca988x
endef
TARGET_DEVICES += netgear_r7500
define Device/netgear_r7500v2
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8064-r7500v2
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7500v2
NETGEAR_HW_ID := 29764958+0+128+512+3x3+4x4
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7500v2
SUPPORTED_DEVICES += r7500v2
DEVICE_TITLE := Netgear Nighthawk X4 R7500v2
DEVICE_PACKAGES := ath10k-firmware-qca99x0 ath10k-firmware-qca988x
endef
TARGET_DEVICES += netgear_r7500v2
define Device/netgear_r7800
$(call Device/DniImage)
DEVICE_DTS := qcom-ipq8065-r7800
KERNEL_SIZE := 2097152
NETGEAR_BOARD_ID := R7800
NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4+cascade
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := r7800
SUPPORTED_DEVICES += r7800
DEVICE_TITLE := Netgear Nighthawk X4S R7800
DEVICE_PACKAGES := ath10k-firmware-qca9984
endef
TARGET_DEVICES += netgear_r7800
define Device/openmesh_a42
$(call Device/FitImageLzma)
FILESYSTEMS := squashfs
DEVICE_DTS := qcom-ipq4019-a42
KERNEL_LOADADDR := 0x80208000
BLOCKSIZE := 64k
SUPPORTED_DEVICES := openmesh,a42
DEVICE_TITLE := OpenMesh A42
KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
IMAGE_SIZE := 15616k
IMAGES = factory.bin sysupgrade.bin
IMAGE/factory.bin/squashfs := append-rootfs | pad-rootfs | openmesh-image ce_type=A42
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca4019 uboot-envtools ipq-wifi-openmesh_a42
endef
TARGET_DEVICES += openmesh_a42
define Device/qcom_ap-dk01.1-c1
PROFILES += $$(DEVICE_NAME)
DEVICE_TITLE := QCA AP-DK01.1-C1
BOARD_NAME := ap-dk01.1-c1
DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1
KERNEL_LOADADDR := 0x80208000
KERNEL_INSTALL := 1
KERNEL_SIZE := 4096k
IMAGE_SIZE := 26624k
FILESYSTEMS := squashfs
$(call Device/FitImage)
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
DEVICE_PACKAGES := ath10k-firmware-qca4019
endef
TARGET_DEVICES += qcom_ap-dk01.1-c1
define Device/qcom_ap-dk04.1-c1
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1
KERNEL_LOADADDR := 0x80208000
KERNEL_INSTALL := 1
KERNEL_SIZE := 4048k
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap-dk04.1-c1
DEVICE_TITLE := QCA AP-DK04.1-C1
endef
TARGET_DEVICES += qcom_ap-dk04.1-c1
define Device/qcom_ipq8064-ap148
$(call Device/FitImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq8064-ap148
KERNEL_INSTALL := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES += ap148
DEVICE_TITLE := Qualcomm AP148
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += qcom_ipq8064-ap148
define Device/qcom_ipq8064-ap148-legacy
$(call Device/LegacyImage)
$(call Device/UbiFit)
DEVICE_DTS := qcom-ipq8064-ap148
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := ap148
SUPPORTED_DEVICES := qcom,ipq8064-ap148 ap148
DEVICE_TITLE := Qualcomm AP148 (legacy)
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += qcom_ipq8064-ap148-legacy
define Device/qcom_ipq8064-db149
$(call Device/FitImage)
DEVICE_DTS := qcom-ipq8064-db149
KERNEL_INSTALL := 1
BOARD_NAME := db149
DEVICE_TITLE := Qualcomm DB149
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += qcom_ipq8064-db149
define Device/tplink_c2600
$(call Device/TpSafeImage)
DEVICE_DTS := qcom-ipq8064-c2600
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := c2600
SUPPORTED_DEVICES += c2600
TPLINK_BOARD_ID := C2600
DEVICE_TITLE := TP-Link Archer C2600
DEVICE_PACKAGES := ath10k-firmware-qca99x0
endef
TARGET_DEVICES += tplink_c2600
define Device/tplink_vr2600v
PROFILES += $$(DEVICE_NAME)
FILESYSTEMS := squashfs
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none
KERNEL_NAME := zImage
KERNEL_SIZE := 2097152
DEVICE_DTS := qcom-ipq8064-vr2600v
BLOCKSIZE := 128k
PAGESIZE := 2048
BOARD_NAME := vr2600v
SUPPORTED_DEVICES += vr2600v
DEVICE_TITLE := TP-Link Archer VR2600v
DEVICE_PACKAGES := ath10k-firmware-qca99x0
IMAGES := sysupgrade.bin
IMAGE/sysupgrade.bin := pad-extra 512 | append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata
endef
TARGET_DEVICES += tplink_vr2600v
define Device/zyxel_nbg6817
DEVICE_DTS := qcom-ipq8065-nbg6817
KERNEL_SIZE := 4096k
BLOCKSIZE := 64k
BOARD_NAME := nbg6817
SUPPORTED_DEVICES += nbg6817
DEVICE_TITLE := ZyXEL NBG6817
DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs kmod-fs-ext4 losetup
$(call Device/ZyXELImage)
endef
TARGET_DEVICES += zyxel_nbg6817
$(eval $(call BuildImage))
Reference in a new issue View git blame Copy permalink