3ef14d0c3d
- Use board engineering names rather than marketing names - Linksys uses a dual firmware layout, where the bootloader will switch to the other stored image when one fails to boot three consecutive times. In order to make this firmware compatible with the factory images and the stock bootloader we must match this layout. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47429
140 lines
2.7 KiB
Diff
140 lines
2.7 KiB
Diff
--- a/arch/arm/boot/dts/Makefile
|
|
+++ b/arch/arm/boot/dts/Makefile
|
|
@@ -120,6 +120,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += kirkwood-
|
|
kirkwood-ds411.dtb \
|
|
kirkwood-ds411j.dtb \
|
|
kirkwood-ds411slim.dtb \
|
|
+ kirkwood-goflexhome.dtb \
|
|
kirkwood-goflexnet.dtb \
|
|
kirkwood-guruplug-server-plus.dtb \
|
|
kirkwood-ib62x0.dtb \
|
|
--- /dev/null
|
|
+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
|
|
@@ -0,0 +1,127 @@
|
|
+/dts-v1/;
|
|
+
|
|
+#include "kirkwood.dtsi"
|
|
+#include "kirkwood-6281.dtsi"
|
|
+
|
|
+/ {
|
|
+ model = "Seagate GoFlex Home";
|
|
+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
|
|
+
|
|
+ memory {
|
|
+ device_type = "memory";
|
|
+ reg = <0x00000000 0x8000000>;
|
|
+ };
|
|
+
|
|
+ chosen {
|
|
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
|
|
+ stdout-path = &uart0;
|
|
+ };
|
|
+
|
|
+ ocp@f1000000 {
|
|
+ pinctrl: pin-controller@10000 {
|
|
+ pmx_usb_power_enable: pmx-usb-power-enable {
|
|
+ marvell,pins = "mpp29";
|
|
+ marvell,function = "gpio";
|
|
+ };
|
|
+ pmx_led_white: pmx-led-white {
|
|
+ marvell,pins = "mpp40";
|
|
+ marvell,function = "gpio";
|
|
+ };
|
|
+ pmx_led_green: pmx-led_green {
|
|
+ marvell,pins = "mpp46";
|
|
+ marvell,function = "gpio";
|
|
+ };
|
|
+ pmx_led_orange: pmx-led-orange {
|
|
+ marvell,pins = "mpp47";
|
|
+ marvell,function = "gpio";
|
|
+ };
|
|
+ };
|
|
+ serial@12000 {
|
|
+ status = "ok";
|
|
+ };
|
|
+
|
|
+ sata@80000 {
|
|
+ status = "okay";
|
|
+ nr-ports = <2>;
|
|
+ };
|
|
+
|
|
+ };
|
|
+ gpio-leds {
|
|
+ compatible = "gpio-leds";
|
|
+
|
|
+ health {
|
|
+ label = "status:green:health";
|
|
+ gpios = <&gpio1 14 1>;
|
|
+ linux,default-trigger = "default-on";
|
|
+ };
|
|
+ fault {
|
|
+ label = "status:orange:fault";
|
|
+ gpios = <&gpio1 15 1>;
|
|
+ };
|
|
+ misc {
|
|
+ label = "status:white:misc";
|
|
+ gpios = <&gpio1 8 1>;
|
|
+ linux,default-trigger = "ide-disk";
|
|
+ };
|
|
+ };
|
|
+ regulators {
|
|
+ compatible = "simple-bus";
|
|
+ #address-cells = <1>;
|
|
+ #size-cells = <0>;
|
|
+ pinctrl-0 = <&pmx_usb_power_enable>;
|
|
+ pinctrl-names = "default";
|
|
+
|
|
+ usb_power: regulator@1 {
|
|
+ compatible = "regulator-fixed";
|
|
+ reg = <1>;
|
|
+ regulator-name = "USB Power";
|
|
+ regulator-min-microvolt = <5000000>;
|
|
+ regulator-max-microvolt = <5000000>;
|
|
+ enable-active-high;
|
|
+ regulator-always-on;
|
|
+ regulator-boot-on;
|
|
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
|
|
+ };
|
|
+ };
|
|
+};
|
|
+
|
|
+&nand {
|
|
+ chip-delay = <40>;
|
|
+ status = "okay";
|
|
+
|
|
+ partition@0 {
|
|
+ label = "u-boot";
|
|
+ reg = <0x0000000 0x100000>;
|
|
+ read-only;
|
|
+ };
|
|
+
|
|
+ partition@100000 {
|
|
+ label = "uImage";
|
|
+ reg = <0x0100000 0x400000>;
|
|
+ };
|
|
+
|
|
+ partition@500000 {
|
|
+ label = "pogoplug";
|
|
+ reg = <0x0500000 0x2000000>;
|
|
+ };
|
|
+
|
|
+ partition@2500000 {
|
|
+ label = "root";
|
|
+ reg = <0x02500000 0xd800000>;
|
|
+ };
|
|
+};
|
|
+
|
|
+&mdio {
|
|
+ status = "okay";
|
|
+
|
|
+ ethphy0: ethernet-phy@0 {
|
|
+ reg = <0>;
|
|
+ };
|
|
+};
|
|
+
|
|
+ð0 {
|
|
+ status = "okay";
|
|
+ ethernet0-port@0 {
|
|
+ phy-handle = <ðphy0>;
|
|
+ };
|
|
+};
|