abbfcc8525
This patch adds supports for the GL-inet GL-MT300N-V2. Specification: - SoC: MediaTek MT7628AN - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR - Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps) - USB: 1 x USB 2.0 port - Button: 1 x switch button, 1 x reset button - LED: 3 x LEDS (system power led is not GPIO controller) - UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND) Installation through Luci: - The original firmware is LEDE, so both LuCI or sysupgrade can be used. - Do not keep settings, for sysupgrade please use the -n option. Installation through bootloader webserver: - Plug power and hold reset button until red LED blink to bright. - Install sysupgrade image using web interface on 192.168.1.1. Signed-off-by: Kyson Lok <kysonlok@gmail.com> [match maximum image size with firmware partition] Signed-off-by: Mathias Kresin <dev@kresin.me>
133 lines
2 KiB
Text
133 lines
2 KiB
Text
/dts-v1/;
|
|
|
|
#include "mt7628an.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/{
|
|
compatible = "gl-inet,gl-mt300n-v2", "ralink,mt7620an-soc";
|
|
model = "GL-MT300N-V2";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,115200";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wan {
|
|
label = "gl-mt300n-v2:blue:wan";
|
|
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
wlan {
|
|
label = "gl-mt300n-v2:red:wlan";
|
|
gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
|
|
BTN_0 {
|
|
label = "BTN_0";
|
|
gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_0>;
|
|
};
|
|
|
|
BTN_1 {
|
|
label = "BTN_1";
|
|
gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <BTN_1>;
|
|
};
|
|
};
|
|
|
|
gpio_export {
|
|
compatible = "gpio-export";
|
|
#size-cells = <0>;
|
|
|
|
usb {
|
|
gpio-export,name = "usb";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "wdt", "gpio", "wled_an", "p0led_an", "i2s";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
mtd-mac-address = <&factory 0x4000>;
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0x0>;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
m25p,chunked-io = <32>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0xfb0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ehci {
|
|
status = "okay";
|
|
};
|
|
|
|
&ohci {
|
|
status = "okay";
|
|
};
|