openwrtv4/target/linux/brcm2708/patches-4.9/0070-Add-IQaudIO-Sound-Card-support-for-Raspberry-Pi.patch

From fcfe9087b79176b5d8afd0ecc4c66013866ef239 Mon Sep 17 00:00:00 2001
From: Gordon Garrity <gordon@iqaudio.com>
Date: Sat, 8 Mar 2014 16:56:57 +0000
Subject: [PATCH] Add IQaudIO Sound Card support for Raspberry Pi

Set a limit of 0dB on Digital Volume Control

The main volume control in the PCM512x DAC has a range up to
+24dB. This is dangerously loud and can potentially cause massive
clipping in the output stages. Therefore this sets a sensible
limit of 0dB for this control.

Allow up to 24dB digital gain to be applied when using IQAudIO DAC+

24db_digital_gain DT param can be used to specify that PCM512x
codec "Digital" volume control should not be limited to 0dB gain,
and if specified will allow the full 24dB gain.

Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt

Add the ability to set the card name, dai name and dai stream name, from
dt config.

Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>

IQaudIO: auto-mute for AMP+ and DigiAMP+

IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute
and auto mute.

Revision 2, auto mute implementing HiassofT suggestion to mute/unmute
using set_bias_level, rather than startup/shutdown....
"By default DAPM waits 5 seconds (pmdown_time) before shutting down
playback streams so a close/stop immediately followed by open/start
doesn't trigger an amp mute+unmute."

Tested on both AMP+ (via DAC+) and DigiAMP+, with both options...

dtoverlay=iqaudio-dacplus,unmute_amp
 "one-shot" unmute when kernel module loads.

dtoverlay=iqaudio-dacplus,auto_mute_amp
 Unmute amp when ALSA device opened by a client. Mute, with 5 second delay
 when ALSA device closed. (Re-opening the device within the 5 second close
 window, will cancel mute.)

Revision 4, using gpiod.

Revision 5, clean-up formatting before adding mute code.
 - Convert tab plus 4 space formatting to 2x tab
 - Remove '// NOT USED' commented code

Revision 6, don't attempt to "one-shot" unmute amp, unless card is
successfully registered.

Signed-off-by: DigitalDreamtime <clive.messer@digitaldreamtime.co.uk>
---
 sound/soc/bcm/Kconfig       |   7 ++
 sound/soc/bcm/Makefile      |   2 +
 sound/soc/bcm/iqaudio-dac.c | 234 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 243 insertions(+)
 create mode 100644 sound/soc/bcm/iqaudio-dac.c

--- a/sound/soc/bcm/Kconfig
+++ b/sound/soc/bcm/Kconfig
@@ -37,3 +37,10 @@ config SND_BCM2708_SOC_RPI_DAC
         select SND_SOC_PCM1794A
         help
          Say Y or M if you want to add support for RPi-DAC.
+
+config SND_BCM2708_SOC_IQAUDIO_DAC
+	tristate "Support for IQaudIO-DAC"
+	depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S
+	select SND_SOC_PCM512x_I2C
+	help
+	  Say Y or M if you want to add support for IQaudIO-DAC.
--- a/sound/soc/bcm/Makefile
+++ b/sound/soc/bcm/Makefile
@@ -12,7 +12,9 @@ obj-$(CONFIG_SND_SOC_CYGNUS) += snd-soc-
 snd-soc-hifiberry-dac-objs := hifiberry_dac.o
 snd-soc-hifiberry-digi-objs := hifiberry_digi.o
 snd-soc-rpi-dac-objs := rpi-dac.o
+snd-soc-iqaudio-dac-objs := iqaudio-dac.o
 
 obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DAC) += snd-soc-hifiberry-dac.o
 obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DIGI) += snd-soc-hifiberry-digi.o
 obj-$(CONFIG_SND_BCM2708_SOC_RPI_DAC) += snd-soc-rpi-dac.o
+obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o
--- /dev/null
+++ b/sound/soc/bcm/iqaudio-dac.c
@@ -0,0 +1,234 @@
+/*
+ * ASoC Driver for IQaudIO DAC
+ *
+ * Author:	Florian Meier <florian.meier@koalo.de>
+ *		Copyright 2013
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/gpio/consumer.h>
+#include <linux/platform_device.h>
+
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/jack.h>
+
+static bool digital_gain_0db_limit = true;
+
+static struct gpio_desc *mute_gpio;
+
+static int snd_rpi_iqaudio_dac_init(struct snd_soc_pcm_runtime *rtd)
+{
+	if (digital_gain_0db_limit)
+	{
+		int ret;
+		struct snd_soc_card *card = rtd->card;
+
+		ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207);
+		if (ret < 0)
+			dev_warn(card->dev, "Failed to set volume limit: %d\n", ret);
+	}
+
+	return 0;
+}
+
+static int snd_rpi_iqaudio_dac_hw_params(struct snd_pcm_substream *substream,
+	struct snd_pcm_hw_params *params)
+{
+	struct snd_soc_pcm_runtime *rtd = substream->private_data;
+	struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
+
+	unsigned int sample_bits =
+		snd_pcm_format_physical_width(params_format(params));
+
+	return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
+}
+
+static void snd_rpi_iqaudio_gpio_mute(struct snd_soc_card *card)
+{
+	if (mute_gpio) {
+		dev_info(card->dev, "%s: muting amp using GPIO22\n",
+			 __func__);
+		gpiod_set_value_cansleep(mute_gpio, 0);
+	}
+}
+
+static void snd_rpi_iqaudio_gpio_unmute(struct snd_soc_card *card)
+{
+	if (mute_gpio) {
+		dev_info(card->dev, "%s: un-muting amp using GPIO22\n",
+			 __func__);
+		gpiod_set_value_cansleep(mute_gpio, 1);
+	}
+}
+
+static int snd_rpi_iqaudio_set_bias_level(struct snd_soc_card *card,
+	struct snd_soc_dapm_context *dapm, enum snd_soc_bias_level level)
+{
+	struct snd_soc_dai *codec_dai = card->rtd[0].codec_dai;
+
+	if (dapm->dev != codec_dai->dev)
+		return 0;
+
+	switch (level) {
+	case SND_SOC_BIAS_PREPARE:
+		if (dapm->bias_level != SND_SOC_BIAS_STANDBY)
+			break;
+
+		/* UNMUTE AMP */
+		snd_rpi_iqaudio_gpio_unmute(card);
+
+		break;
+	case SND_SOC_BIAS_STANDBY:
+		if (dapm->bias_level != SND_SOC_BIAS_PREPARE)
+			break;
+
+		/* MUTE AMP */
+		snd_rpi_iqaudio_gpio_mute(card);
+
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+/* machine stream operations */
+static struct snd_soc_ops snd_rpi_iqaudio_dac_ops = {
+	.hw_params = snd_rpi_iqaudio_dac_hw_params,
+};
+
+static struct snd_soc_dai_link snd_rpi_iqaudio_dac_dai[] = {
+{
+	.cpu_dai_name	= "bcm2708-i2s.0",
+	.codec_dai_name	= "pcm512x-hifi",
+	.platform_name	= "bcm2708-i2s.0",
+	.codec_name	= "pcm512x.1-004c",
+	.dai_fmt	= SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF |
+				SND_SOC_DAIFMT_CBS_CFS,
+	.ops		= &snd_rpi_iqaudio_dac_ops,
+	.init		= snd_rpi_iqaudio_dac_init,
+},
+};
+
+/* audio machine driver */
+static struct snd_soc_card snd_rpi_iqaudio_dac = {
+	.owner        = THIS_MODULE,
+	.dai_link     = snd_rpi_iqaudio_dac_dai,
+	.num_links    = ARRAY_SIZE(snd_rpi_iqaudio_dac_dai),
+};
+
+static int snd_rpi_iqaudio_dac_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	bool gpio_unmute = false;
+
+	snd_rpi_iqaudio_dac.dev = &pdev->dev;
+
+	if (pdev->dev.of_node) {
+		struct device_node *i2s_node;
+		struct snd_soc_card *card = &snd_rpi_iqaudio_dac;
+		struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_dac_dai[0];
+		bool auto_gpio_mute = false;
+
+		i2s_node = of_parse_phandle(pdev->dev.of_node,
+					    "i2s-controller", 0);
+		if (i2s_node) {
+			dai->cpu_dai_name = NULL;
+			dai->cpu_of_node = i2s_node;
+			dai->platform_name = NULL;
+			dai->platform_of_node = i2s_node;
+		}
+
+		digital_gain_0db_limit = !of_property_read_bool(
+			pdev->dev.of_node, "iqaudio,24db_digital_gain");
+
+		if (of_property_read_string(pdev->dev.of_node, "card_name",
+					    &card->name))
+			card->name = "IQaudIODAC";
+
+		if (of_property_read_string(pdev->dev.of_node, "dai_name",
+					    &dai->name))
+			dai->name = "IQaudIO DAC";
+
+		if (of_property_read_string(pdev->dev.of_node,
+					"dai_stream_name", &dai->stream_name))
+			dai->stream_name = "IQaudIO DAC HiFi";
+
+		/* gpio_unmute - one time unmute amp using GPIO */
+		gpio_unmute = of_property_read_bool(pdev->dev.of_node,
+						    "iqaudio-dac,unmute-amp");
+
+		/* auto_gpio_mute - mute/unmute amp using GPIO */
+		auto_gpio_mute = of_property_read_bool(pdev->dev.of_node,
+						"iqaudio-dac,auto-mute-amp");
+
+		if (auto_gpio_mute || gpio_unmute) {
+			mute_gpio = devm_gpiod_get_optional(&pdev->dev, "mute",
+							    GPIOD_OUT_LOW);
+			if (IS_ERR(mute_gpio)) {
+				ret = PTR_ERR(mute_gpio);
+				dev_err(&pdev->dev,
+					"Failed to get mute gpio: %d\n", ret);
+				return ret;
+			}
+
+			if (auto_gpio_mute && mute_gpio)
+				snd_rpi_iqaudio_dac.set_bias_level =
+						snd_rpi_iqaudio_set_bias_level;
+		}
+	}
+
+	ret = snd_soc_register_card(&snd_rpi_iqaudio_dac);
+	if (ret) {
+		dev_err(&pdev->dev,
+			"snd_soc_register_card() failed: %d\n", ret);
+		return ret;
+	}
+
+	if (gpio_unmute && mute_gpio)
+		snd_rpi_iqaudio_gpio_unmute(&snd_rpi_iqaudio_dac);
+
+	return 0;
+}
+
+static int snd_rpi_iqaudio_dac_remove(struct platform_device *pdev)
+{
+	snd_rpi_iqaudio_gpio_mute(&snd_rpi_iqaudio_dac);
+
+	return snd_soc_unregister_card(&snd_rpi_iqaudio_dac);
+}
+
+static const struct of_device_id iqaudio_of_match[] = {
+	{ .compatible = "iqaudio,iqaudio-dac", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, iqaudio_of_match);
+
+static struct platform_driver snd_rpi_iqaudio_dac_driver = {
+	.driver = {
+		.name   = "snd-rpi-iqaudio-dac",
+		.owner  = THIS_MODULE,
+		.of_match_table = iqaudio_of_match,
+	},
+	.probe          = snd_rpi_iqaudio_dac_probe,
+	.remove         = snd_rpi_iqaudio_dac_remove,
+};
+
+module_platform_driver(snd_rpi_iqaudio_dac_driver);
+
+MODULE_AUTHOR("Florian Meier <florian.meier@koalo.de>");
+MODULE_DESCRIPTION("ASoC Driver for IQAudio DAC");
+MODULE_LICENSE("GPL v2");