openwrtv4/target/linux/mediatek/patches-4.14/0193-clk-mediatek-adjust-dependency-of-reset.c-to-avoid-u.patch
Stijn Tintel 64b53247c4 kernel: bump 4.14 to 4.14.44
Refresh patches.

Remove upstreamed patch:
generic/pending/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
Update patches that no longer applies:
generic/hack/901-debloat_sock_diag.patch

Compile-tested on: x86/64.
Runtime-tested on: x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-05-29 00:53:15 +03:00

71 lines
2.8 KiB
Diff

From 0f9391b4ee12cad5c93e109b9eb6c0c6298da0d3 Mon Sep 17 00:00:00 2001
From: Sean Wang <sean.wang@mediatek.com>
Date: Fri, 5 Jan 2018 16:14:06 +0800
Subject: [PATCH 193/224] clk: mediatek: adjust dependency of reset.c to avoid
unexpectedly being built
Changes from v1->v2:
Add 'select RESET_CONTROLLER' under COMMON_CLK_MEDIATEK and enable
reset.c to be built when COMMON_CLK_MEDIATEK is selected. That should
be quite reasonable because the reset controller is tightly embedded
inside and exported from these clock subsystems. At least it can be found
on infracfg and pericfg subsystem that both are really fundamental block
lots of devices must depend on.
commit 74cb0d6dde8 ("clk: mediatek: fixup test-building of MediaTek clock
drivers") can let the build system looking into the directory where the
clock drivers resides and then allow test-building the drivers.
But the change also gives rise to certain incorrect behavior which is
reset.c being built even not depending on either COMPILE_TEST or
ARCH_MEDIATEK alternative dependency. To get rid of reset.c being built
unexpectedly on the other platforms, it would be a good change that the
file should be built depending on its own specific configuration rather
than just on generic RESET_CONTROLLER one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clk/mediatek/Kconfig | 1 +
drivers/clk/mediatek/Makefile | 4 ++--
drivers/clk/mediatek/clk-mtk.h | 7 -------
3 files changed, 3 insertions(+), 9 deletions(-)
--- a/drivers/clk/mediatek/Kconfig
+++ b/drivers/clk/mediatek/Kconfig
@@ -6,6 +6,7 @@ menu "Clock driver for MediaTek SoC"
config COMMON_CLK_MEDIATEK
bool
+ select RESET_CONTROLLER
---help---
MediaTek SoCs' clock support.
--- a/drivers/clk/mediatek/Makefile
+++ b/drivers/clk/mediatek/Makefile
@@ -1,6 +1,5 @@
# SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_COMMON_CLK_MEDIATEK) += clk-mtk.o clk-pll.o clk-gate.o clk-apmixed.o clk-cpumux.o
-obj-$(CONFIG_RESET_CONTROLLER) += reset.o
+obj-$(CONFIG_COMMON_CLK_MEDIATEK) += clk-mtk.o clk-pll.o clk-gate.o clk-apmixed.o clk-cpumux.o reset.o
obj-$(CONFIG_COMMON_CLK_MT6797) += clk-mt6797.o
obj-$(CONFIG_COMMON_CLK_MT6797_IMGSYS) += clk-mt6797-img.o
obj-$(CONFIG_COMMON_CLK_MT6797_MMSYS) += clk-mt6797-mm.o
--- a/drivers/clk/mediatek/clk-mtk.h
+++ b/drivers/clk/mediatek/clk-mtk.h
@@ -229,14 +229,7 @@ void mtk_clk_register_plls(struct device
struct clk *mtk_clk_register_ref2usb_tx(const char *name,
const char *parent_name, void __iomem *reg);
-#ifdef CONFIG_RESET_CONTROLLER
void mtk_register_reset_controller(struct device_node *np,
unsigned int num_regs, int regofs);
-#else
-static inline void mtk_register_reset_controller(struct device_node *np,
- unsigned int num_regs, int regofs)
-{
-}
-#endif
#endif /* __DRV_CLK_MTK_H */