7a873974f7
Use diag.sh version used for apm821xx, ipq40xx and ipq806x, which supports different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [reword commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
147 lines
2.2 KiB
Text
147 lines
2.2 KiB
Text
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "ar9330.dtsi"
|
|
|
|
/ {
|
|
model = "GL.iNet GL-AR150";
|
|
compatible = "glinet,ar150", "qca,ar9330";
|
|
|
|
aliases {
|
|
serial0 = &uart;
|
|
led-boot = &wlan;
|
|
led-failsafe = &wlan;
|
|
led-upgrade = &wlan;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wlan: wlan {
|
|
label = "gl-ar150:orange:wlan";
|
|
gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
lan {
|
|
label = "gl-ar150:green:lan";
|
|
gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
wan {
|
|
label = "gl-ar150:green:wan";
|
|
gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys-polled";
|
|
poll-interval = <100>;
|
|
|
|
manual {
|
|
label = "manual";
|
|
linux,code = <BTN_7>;
|
|
gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
auto {
|
|
label = "auto";
|
|
linux,code = <BTN_8>;
|
|
gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb {
|
|
dr_mode = "host";
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_phy {
|
|
status = "okay";
|
|
gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&spi {
|
|
num-chipselects = <1>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <104000000>;
|
|
reg = <0>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x000000 0x040000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1 {
|
|
label = "u-boot-env";
|
|
reg = <0x040000 0x010000>;
|
|
};
|
|
|
|
partition@2 {
|
|
label = "firmware";
|
|
reg = <0x050000 0xfa0000>;
|
|
};
|
|
|
|
art: partition@3 {
|
|
label = "ART";
|
|
reg = <0xff0000 0x010000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ð0 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x0>;
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
mtd-mac-address = <&art 0x0>;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
|
|
switch-phy-addr-swap = <0>;
|
|
switch-phy-swap = <0>;
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
mtd-cal-data = <&art 0x1000>;
|
|
mtd-mac-address = <&art 0x0>;
|
|
};
|