openwrtv4/target/linux/ramips/base-files/etc/board.d/02_network
Robert Marko d0ef27594a ramips: add support for TP-Link TL-WR840N v5
TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button

* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
  Orange LED is registered so you can later use it for your own purposes.

  Flash instruction:

  Unlike TL-WR840N v4 flashing through WEB UI works in v5.
  1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
  2. Go to 192.168.0.1
  3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
  4. Wait until green LED stops flashing and use the router.

Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.

After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2017-11-08 23:25:05 +01:00

530 lines
9.9 KiB
Bash
Executable file

#!/bin/sh
. /lib/functions.sh
. /lib/functions/uci-defaults.sh
. /lib/functions/system.sh
ramips_setup_rt3x5x_vlans()
{
if [ ! -x /sbin/swconfig ]; then
# legacy default
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
return
fi
local wanports=""
local lanports=""
for port in 5 4 3 2 1 0; do
if [ `swconfig dev rt305x port $port get disable` = "1" ]; then
continue
fi
if [ `swconfig dev rt305x port $port get lan` = "0" ]; then
wanports="$port:wan $wanports"
else
lanports="$port:lan $lanports"
fi
done
ucidef_add_switch "rt305x" $lanports $wanports "6t@eth0"
}
ramips_setup_interfaces()
{
local board="$1"
case $board in
11acnas|\
w2914nsv2|\
zbt-we2026)
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
;;
3g150b|\
3g300m|\
a5-v11|\
all0256n-4M|\
all0256n-8M|\
all5002|\
all5003|\
broadway|\
dcs-930|\
dcs-930l-b1|\
ht-tm02|\
linkits7688 | \
linkits7688d | \
m2m|\
microwrt|\
mpr-a2|\
ncs601w|\
omega2 | \
omega2p | \
timecloud|\
w150m|\
widora-neo|\
wnce2001|\
zbt-cpe102|\
zte-q7)
ucidef_add_switch "switch0"
ucidef_add_switch_attr "switch0" "enable" "false"
ucidef_set_interface_lan "eth0"
;;
mlw221|\
mr-102n)
ucidef_set_interface_lan "eth0.2"
;;
3g-6200n|\
ai-br100|\
d240|\
db-wrt01|\
dir-300-b7|\
dir-320-b1|\
dir-610-a1|\
dir-615-h1|\
ew1200|\
firewrt|\
hc5661a|\
hc5962|\
hlk-rm04|\
k2p|\
kn|\
kn_rc|\
mac1200rv2|\
miwifi-mini|\
miwifi-nano|\
mt7621|\
mt7628|\
mzk-750dhp|\
mzk-w300nh2|\
nixcore-x1-8M|\
nixcore-x1-16M|\
oy-0001|\
pbr-m1|\
psg1208|\
psg1218a|\
r6220|\
sap-g3200u3|\
sk-wb8|\
vr500|\
wf-2881|\
witi|\
wl-wn575a3|\
wndr3700v5|\
wt1520-4M|\
wt1520-8M|\
y1|\
youku-yk1|\
zbt-ape522ii|\
zbt-we1326|\
zbt-we826-16M|\
zbt-we826-32M|\
zbt-wg2626|\
zbt-wg3526-16M|\
zbt-wg3526-32M|\
zbt-wr8305rt)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
;;
mir3g)
ucidef_add_switch "switch0" \
"2:lan:2" "3:lan:1" "1:wan" "6t@eth0"
;;
psg1218b)
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:2" "2:lan:1" "3:wan" "6@eth0"
;;
whr-300hp2|\
whr-600d|\
wsr-1166|\
wsr-600)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "4:wan:5" "6@eth0"
;;
ar670w|\
ar725w|\
rt-ac51u)
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
;;
rt-n15|\
wl-351)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
;;
asl26555-8M|\
asl26555-16M|\
rp-n53)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
;;
atp-52b|\
awm002-evb-4M|\
awm002-evb-8M|\
c20i|\
dir-645|\
f5d8235-v2|\
gl-mt300a|\
gl-mt300n|\
gl-mt750|\
hg255d|\
jhr-n805r|\
jhr-n825r|\
jhr-n926r|\
mzk-wdpr|\
rb750gr3|\
rt-n14u|\
tl-wr840n-v4|\
tl-wr840n-v5|\
tl-wr841n-v13|\
ubnt-erx|\
ubnt-erx-sfp|\
ur-326n4g|\
wrtnode|\
wrtnode2p | \
wrtnode2r | \
wt3020-4M|\
wt3020-8M|\
zbt-wa05)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
;;
c20|\
c50)
ucidef_add_switch "switch0" \
"1:lan:3" "2:lan:4" "3:lan:1" "4:lan:2" "0:wan" "6@eth0"
;;
dir-860l-b1)
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
;;
gb-pc1)
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6@eth0"
;;
gl-mt300n-v2)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6@eth0"
;;
awapn2403)
ucidef_add_switch "switch0" \
"0:lan" "1:wan" "6@eth0"
;;
b2c|\
nw718|\
psr-680w|\
sl-r7205|\
ur-336un|\
w502u|\
wr6202)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
;;
br-6475nd)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
;;
c108|\
cf-wr800n)
ucidef_add_switch "switch0" \
"4:lan" "6t@eth0"
;;
cy-swr1100)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0"
;;
cs-qr10|\
d105|\
dch-m225|\
ex2700|\
ex3700|\
hpm|\
mzk-ex300np|\
mzk-ex750np|\
na930|\
pbr-d1|\
u25awf-h1|\
wli-tx4-ag300n|\
wmdr-143n|\
wmr-300|\
wn3000rpv3|\
wrh-300cr)
ucidef_set_interface_lan "eth0"
;;
duzun-dm06)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6@eth0"
;;
e1700|\
mt7620a_mt7530)
ucidef_add_switch "switch1" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
;;
hc5*61|\
y1s)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
;;
kn_rf)
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
;;
kng_rc)
ucidef_add_switch "switch1" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "7t@eth0"
;;
mlwg2|\
wizard8800|\
wl-330n)
ucidef_set_interface_lan "eth0.1"
;;
mr200)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
ucidef_set_interface_wan "usb0"
;;
mzk-dp150n|\
vocore-8M|\
vocore-16M)
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6t@eth0"
;;
newifi-d1)
ucidef_add_switch "switch0" \
"1:lan:2" "2:lan:1" "4:wan" "6@eth0"
;;
re350-v1)
ucidef_add_switch "switch0" \
"0:lan" "6@eth0"
;;
re6500)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "6@eth0"
;;
rt-n56u)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
;;
tew-638apb-v2)
ucidef_add_switch "switch0" \
"4:lan" "6@eth0"
;;
tew-691gr|\
tew-692gr|\
wlr-6000)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
;;
vocore2|\
vocore2lite)
ucidef_add_switch "switch0" \
"0:lan" "2:lan" "6t@eth0"
;;
f5d8235-v1|\
tew-714tru|\
v11st-fe|\
wzr-agl300nh)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
;;
wcr-1166ds)
ucidef_add_switch "switch0" \
"3:lan" "4:wan" "6@eth0"
;;
wcr-150gn|\
we1026-5g-16m)
ucidef_add_switch "switch0" \
"0:lan" "6t@eth0"
;;
whr-1166d)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "5:wan" "6@eth0"
;;
wizfi630a)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "0:wan" "6@eth0"
;;
*)
RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
if [ -n "${RT3X5X}" ]; then
ramips_setup_rt3x5x_vlans
else
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
fi
;;
esac
}
ramips_setup_macs()
{
local board="$1"
local lan_mac=""
local wan_mac=""
case $board in
a5-v11|\
ht-tm02|\
wmdr-143n)
lan_mac=$(cat /sys/class/net/eth0/address)
;;
all0239-3g|\
carambola|\
freestation5|\
w502u|\
wnce2001)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
bc2|\
broadway|\
d105|\
dir-300-b7|\
dir-320-b1|\
dir-620-a1|\
esr-9753|\
freestation5|\
hlk-rm04|\
mpr-a1|\
psr-680w|\
sl-r7205|\
y1|\
y1s)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
br-6475nd)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(mtd_get_mac_binary devdata 7)
;;
cy-swr1100|\
dch-m225)
lan_mac=$(mtd_get_mac_ascii factory lanmac)
;;
dir-645)
lan_mac=$(mtd_get_mac_ascii nvram lanmac)
wan_mac=$(mtd_get_mac_ascii nvram wanmac)
;;
dir-860l-b1)
lan_mac=$(mtd_get_mac_ascii factory lanmac)
wan_mac=$(mtd_get_mac_ascii factory wanmac)
;;
e1700)
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
;;
gl-mt300n-v2)
wan_mac=$(mtd_get_mac_binary factory 4)
;;
hc5*61|\
hc5661a|\
hc5962)
lan_mac=`mtd_get_mac_ascii bdinfo "Vfac_mac "`
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
kn_rc|\
kn_rf|\
kng_rc)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
linkits7688 | \
linkits7688d)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(mtd_get_mac_binary factory 46)
;;
mac1200rv2)
lan_mac=$(mtd_get_mac_binary factory_info 13)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
mir3g)
lan_mac=$(mtd_get_mac_binary Factory 0xe006)
;;
miwifi-mini)
wan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$wan_mac")
;;
m3|\
m4-4M|\
m4-8M|\
x5|\
x8)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_add "$lan_mac" -2)
;;
newifi-d1)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_add "$lan_mac" 2)
;;
omega2|\
omega2p)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(mtd_get_mac_binary factory 46)
;;
oy-0001)
lan_mac=$(mtd_get_mac_binary factory 40)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
r6220)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
rt-n56u)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(mtd_get_mac_binary factory 32772)
;;
sk-wb8)
wan_mac=$(mtd_get_mac_binary factory 57350)
;;
tew-691gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3)
;;
tew-692gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 1)
;;
tiny-ac)
lan_mac=$(mtd_get_mac_ascii u-boot-env LAN_MAC_ADDR)
wan_mac=$(mtd_get_mac_ascii u-boot-env WAN_MAC_ADDR)
;;
vr500)
lan_mac=$(mtd_get_mac_binary factory 57344)
wan_mac=$(mtd_get_mac_binary factory 57350)
;;
w306r-v20)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 5)
;;
wcr-1166ds|\
wsr-1166)
local index="$(find_mtd_index "board_data")"
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
lan_mac=$wan_mac
;;
wcr-150gn)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
whr-1166d|\
whr-300hp2|\
whr-600d|\
wsr-600)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$wan_mac
;;
wizfi630a)
lan_mac=$(mtd_get_mac_binary factory 4)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
wlr-6000)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2)
;;
*)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
}
board_config_update
board=$(board_name)
ramips_setup_interfaces $board
ramips_setup_macs $board
board_config_flush
exit 0