c51c976db8
The VoCore2 features 128MB of RAM, therefore set memory in DTS to 128*1024*1024 = 0x8000000 The board's LED is connected to GND, set it to ACTIVE_HIGH here. Make serial console working again on kernel 4.9 by change of pinmux configuration. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
104 lines
1.4 KiB
Text
104 lines
1.4 KiB
Text
/dts-v1/;
|
|
|
|
#include "mt7628an.dtsi"
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
compatible = "vocore,VoCore2", "mediatek,mt7628an-soc";
|
|
model = "VoCore2";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS2,115200";
|
|
};
|
|
|
|
memory@0 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x8000000>;
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
status {
|
|
label = "vocore2:fuchsia:status";
|
|
gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "wled_an", "perst", "wdt";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0x4>;
|
|
};
|
|
|
|
&spi0 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <10000000>;
|
|
m25p,chunked-io = <32>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0xfb0000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&esw {
|
|
mediatek,portmap = <0x7>;
|
|
mediatek,portdisable = <0x3a>;
|
|
};
|
|
|
|
&i2s {
|
|
status = "okay";
|
|
};
|
|
|
|
&gdma {
|
|
status = "okay";
|
|
};
|
|
|
|
&pwm {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart2 {
|
|
status = "okay";
|
|
};
|