b6a4c67468
This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs Not working: - USB port Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
177 lines
4 KiB
Bash
177 lines
4 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ath9k_eeprom_die() {
|
|
echo "ath9k eeprom: " "$*"
|
|
exit 1
|
|
}
|
|
|
|
ath9k_eeprom_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
|
|
mtd=$(find_mtd_chardev $part)
|
|
[ -n "$mtd" ] || \
|
|
ath9k_eeprom_die "no mtd device found for partition $part"
|
|
|
|
dd if=$mtd of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath9k_eeprom_die "failed to extract from $mtd"
|
|
}
|
|
|
|
ath9k_ubi_eeprom_extract() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local ubidev=$(nand_find_ubi $CI_UBIPART)
|
|
local ubi
|
|
|
|
ubi=$(nand_find_volume $ubidev $part)
|
|
[ -n "$ubi" ] || \
|
|
ath9k_eeprom_die "no UBI volume found for $part"
|
|
|
|
dd if=/dev/$ubi of=/lib/firmware/$FIRMWARE bs=1 skip=$offset count=$count 2>/dev/null || \
|
|
ath9k_eeprom_die "failed to extract from $ubi"
|
|
}
|
|
|
|
ath9k_eeprom_extract_reverse() {
|
|
local part=$1
|
|
local offset=$2
|
|
local count=$3
|
|
local mtd
|
|
local reversed
|
|
local caldata
|
|
|
|
mtd=$(find_mtd_chardev "$part")
|
|
reversed=$(hexdump -v -s $offset -n $count -e '/1 "%02x "' $mtd)
|
|
|
|
for byte in $reversed; do
|
|
caldata="\x${byte}${caldata}"
|
|
done
|
|
|
|
printf "%b" "$caldata" > /lib/firmware/$FIRMWARE
|
|
}
|
|
|
|
ath9k_patch_firmware_mac() {
|
|
local mac=$1
|
|
|
|
[ -z "$mac" ] && return
|
|
|
|
macaddr_2bin $mac | dd of=/lib/firmware/$FIRMWARE conv=notrunc bs=1 seek=2 count=6
|
|
}
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"soc_wmac.eeprom")
|
|
case $board in
|
|
c-55|\
|
|
c-60)
|
|
ath9k_eeprom_extract "art" 4096 2048
|
|
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1)
|
|
;;
|
|
fritz4020)
|
|
ath9k_eeprom_extract_reverse "urlader" 5441 1088
|
|
;;
|
|
mr18)
|
|
. /lib/upgrade/nand.sh
|
|
|
|
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
|
|
ath9k_ubi_eeprom_extract "caldata" 4096 2048
|
|
else
|
|
ath9k_eeprom_extract "odm-caldata" 4096 2048
|
|
fi
|
|
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +1)
|
|
;;
|
|
r6100 | \
|
|
wndr3700v4 | \
|
|
wndr4300)
|
|
ath9k_eeprom_extract "caldata" 4096 2048
|
|
ath9k_patch_firmware_mac $(mtd_get_mac_binary caldata 0)
|
|
;;
|
|
rambutan)
|
|
ath9k_eeprom_extract "art" 4096 2048
|
|
;;
|
|
wlr8100)
|
|
ath9k_eeprom_extract "art" 4096 2048
|
|
ath9k_patch_firmware_mac $(mtd_get_mac_ascii u-boot-env "ethaddr")
|
|
;;
|
|
z1)
|
|
. /lib/upgrade/nand.sh
|
|
|
|
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
|
|
ath9k_ubi_eeprom_extract "caldata" 4096 2048
|
|
else
|
|
ath9k_eeprom_extract "origcaldata" 4096 2048
|
|
fi
|
|
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +2)
|
|
;;
|
|
*)
|
|
ath9k_eeprom_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
|
|
"pci_wmac0.eeprom")
|
|
case $board in
|
|
c-55)
|
|
ath9k_eeprom_extract "art" 20480 2048
|
|
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +2)
|
|
;;
|
|
fritz300e)
|
|
ath9k_eeprom_extract_reverse "urloader" 5441 1088
|
|
;;
|
|
mr18)
|
|
. /lib/upgrade/nand.sh
|
|
|
|
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
|
|
ath9k_ubi_eeprom_extract "caldata" 20480 2048
|
|
else
|
|
ath9k_eeprom_extract "odm-caldata" 20480 2048
|
|
fi
|
|
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +2)
|
|
;;
|
|
wndr3700v4 | \
|
|
wndr4300)
|
|
ath9k_eeprom_extract "caldata" 20480 2048
|
|
ath9k_patch_firmware_mac $(mtd_get_mac_binary caldata 12)
|
|
;;
|
|
z1)
|
|
. /lib/upgrade/nand.sh
|
|
|
|
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
|
|
ath9k_ubi_eeprom_extract "caldata" 86016 4096
|
|
else
|
|
ath9k_eeprom_extract "origcaldata" 86016 4096
|
|
fi
|
|
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +3)
|
|
;;
|
|
*)
|
|
ath9k_eeprom_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
|
|
"pci_wmac1.eeprom")
|
|
case $board in
|
|
mr18)
|
|
. /lib/upgrade/nand.sh
|
|
|
|
if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
|
|
ath9k_ubi_eeprom_extract "caldata" 36864 2048
|
|
else
|
|
ath9k_eeprom_extract "odm-caldata" 36864 2048
|
|
fi
|
|
ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +3)
|
|
;;
|
|
*)
|
|
ath9k_eeprom_die "board $board is not supported yet"
|
|
;;
|
|
esac
|
|
;;
|
|
esac
|