openwrtv4/target/linux/ramips/base-files/etc/board.d/02_network
Oliver Fleischmann a92c64e8ae ramips: add support for Loewe WMDR-143N
The WMDR-143N is a small module originally used as a Wifi client
in some Loewe smart TV sets. It is sold cheaply at german surplus
shops. The module contains a RT3662 SOC.

Specifications:

- 500 MHz CPU Clock
- 1x 10/100Mbps Ethernet (pin header)
- 32 MB of RAM
- 8 MB of FLASH
- 2T3R 2.4/5 GHz (SOC internal)
- 3 Antennas on PCB
- UART pads on PCB (J3: 1 = +3.3V, 2 = RX, 3 = TX, 4 = GND), TX
  and RX are 3,3V only! The square hole is pin 1
- Power supply pads on PCB (J6: 1 and 2 = +5V, 3 and 4 = GND)
  The square hole is pin 1

The original firmware has two identical kernel/rootfs images and
two "Factory" calibration data blocks in flash. The LEDE image
leaves only the first "Factory" block in place and uses both
"Kernel" blocks and the redundant "Factory" block together to gain
enough space for the jffs2 partition.

Flash instructions:

You need UART and Ethernet connections to flash the board. Use
the LEDE "sysupgrade.bin" image with tftp.

Apply power to the board and in the first 5 seconds, hit 2 to
select TFTP upload. The bootloader asks for board- and server IP
addresses and filename.

Alternate method: With the vendor firmware running, assign an IP
address to the ethernet port, tftp the firmware image to
/tmp and write to mtd4 ("KernelA").

Signed-off-by: Oliver Fleischmann <ogf@bnv-bamberg.de>
[remove pinctrl node from dts, no pin is used as GPIO]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-27 09:13:27 +02:00

515 lines
9.6 KiB
Bash
Executable file

#!/bin/sh
. /lib/functions.sh
. /lib/functions/uci-defaults.sh
. /lib/functions/system.sh
ramips_setup_rt3x5x_vlans()
{
if [ ! -x /sbin/swconfig ]; then
# legacy default
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
return
fi
local wanports=""
local lanports=""
for port in 5 4 3 2 1 0; do
if [ `swconfig dev rt305x port $port get disable` = "1" ]; then
continue
fi
if [ `swconfig dev rt305x port $port get lan` = "0" ]; then
wanports="$port:wan $wanports"
else
lanports="$port:lan $lanports"
fi
done
ucidef_add_switch "rt305x" $lanports $wanports "6t@eth0"
}
ramips_setup_interfaces()
{
local board="$1"
case $board in
11acnas|\
w2914nsv2|\
zbt-we2026)
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan:5" "6@eth0"
;;
3g150b|\
3g300m|\
a5-v11|\
all0256n-4M|\
all0256n-8M|\
all5002|\
all5003|\
broadway|\
dcs-930|\
dcs-930l-b1|\
ht-tm02|\
linkits7688 | \
linkits7688d | \
m2m|\
microwrt|\
mpr-a2|\
ncs601w|\
omega2 | \
omega2p | \
timecloud|\
w150m|\
widora-neo|\
wnce2001|\
zbt-cpe102|\
zte-q7)
ucidef_add_switch "switch0"
ucidef_add_switch_attr "switch0" "enable" "false"
ucidef_set_interface_lan "eth0"
;;
mlw221|\
mr-102n)
ucidef_set_interface_lan "eth0.2"
;;
3g-6200n|\
ai-br100|\
d240|\
db-wrt01|\
dir-300-b7|\
dir-320-b1|\
dir-610-a1|\
dir-615-h1|\
ew1200|\
firewrt|\
hc5661a|\
hc5962|\
hlk-rm04|\
k2p|\
kn|\
kn_rc|\
mac1200rv2|\
miwifi-mini|\
miwifi-nano|\
mt7621|\
mt7628|\
mzk-750dhp|\
mzk-w300nh2|\
nixcore-x1-8M|\
nixcore-x1-16M|\
oy-0001|\
pbr-m1|\
psg1208|\
psg1218a|\
r6220|\
sap-g3200u3|\
sk-wb8|\
vr500|\
wf-2881|\
witi|\
wl-wn575a3|\
wndr3700v5|\
wt1520-4M|\
wt1520-8M|\
y1|\
youku-yk1|\
zbt-ape522ii|\
zbt-we1326|\
zbt-we826-16M|\
zbt-we826-32M|\
zbt-wg2626|\
zbt-wg3526-16M|\
zbt-wg3526-32M|\
zbt-wr8305rt)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
;;
psg1218b)
ucidef_add_switch "switch0" \
"0:lan:3" "1:lan:2" "2:lan:1" "3:wan" "6@eth0"
;;
whr-300hp2|\
whr-600d|\
wsr-1166|\
wsr-600)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "4:wan:5" "6@eth0"
;;
ar670w|\
ar725w|\
rt-ac51u)
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
;;
rt-n15|\
wl-351)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
;;
asl26555-8M|\
asl26555-16M|\
rp-n53)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6t@eth0"
;;
atp-52b|\
awm002-evb-4M|\
awm002-evb-8M|\
awm003-evb|\
c20i|\
c50|\
dir-645|\
f5d8235-v2|\
gl-mt300a|\
gl-mt300n|\
gl-mt750|\
hg255d|\
jhr-n805r|\
jhr-n825r|\
jhr-n926r|\
mzk-wdpr|\
rb750gr3|\
rt-n14u|\
tl-wr840n-v4|\
tl-wr841n-v13|\
ubnt-erx|\
ubnt-erx-sfp|\
ur-326n4g|\
wrtnode|\
wrtnode2p | \
wrtnode2r | \
wt3020-4M|\
wt3020-8M|\
zbt-wa05)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
;;
dir-860l-b1)
ucidef_add_switch "switch0" \
"1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "0:wan" "6@eth0"
;;
gb-pc1)
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6@eth0"
;;
gl-mt300n-v2)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6@eth0"
;;
awapn2403)
ucidef_add_switch "switch0" \
"0:lan" "1:wan" "6@eth0"
;;
b2c|\
nw718|\
psr-680w|\
sl-r7205|\
ur-336un|\
w502u|\
wr6202)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
;;
br-6475nd)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
;;
cf-wr800n)
ucidef_add_switch "switch0" \
"4:lan" "6t@eth0"
;;
cy-swr1100)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0"
;;
cs-qr10|\
d105|\
dch-m225|\
ex2700|\
ex3700|\
hpm|\
mzk-ex300np|\
mzk-ex750np|\
na930|\
pbr-d1|\
wli-tx4-ag300n|\
wmdr-143n|\
wmr-300|\
wn3000rpv3|\
wrh-300cr)
ucidef_set_interface_lan "eth0"
;;
duzun-dm06)
ucidef_add_switch "switch0" \
"1:lan" "0:wan" "6@eth0"
;;
e1700|\
mt7620a_mt7530)
ucidef_add_switch "switch1" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0"
;;
hc5*61|\
y1s)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5:lan" "0:wan" "6@eth0"
;;
kn_rf)
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6@eth0"
;;
kng_rc)
ucidef_add_switch "switch1" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "7t@eth0"
;;
mlwg2|\
wizard8800|\
wl-330n)
ucidef_set_interface_lan "eth0.1"
;;
mr200)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "6t@eth0"
ucidef_set_interface_wan "usb0"
;;
mzk-dp150n|\
vocore-8M|\
vocore-16M)
ucidef_add_switch "switch0" \
"0:lan" "4:lan" "6t@eth0"
;;
newifi-d1)
ucidef_add_switch "switch0" \
"1:lan:2" "2:lan:1" "4:wan" "6@eth0"
;;
re350-v1)
ucidef_add_switch "switch0" \
"0:lan" "6@eth0"
;;
re6500)
ucidef_add_switch "switch0" \
"0:lan:1" "1:lan:2" "2:lan:3" "3:lan:4" "6@eth0"
;;
rt-n56u)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
;;
tew-638apb-v2)
ucidef_add_switch "switch0" \
"4:lan" "6@eth0"
;;
tew-691gr|\
tew-692gr|\
wlr-6000)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0"
;;
vocore2)
ucidef_add_switch "switch0" \
"0:lan" "2:lan" "6t@eth0"
;;
f5d8235-v1|\
tew-714tru|\
v11st-fe|\
wzr-agl300nh)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
;;
wcr-1166ds)
ucidef_add_switch "switch0" \
"3:lan" "4:wan" "6@eth0"
;;
wcr-150gn)
ucidef_add_switch "switch0" \
"0:lan" "6t@eth0"
;;
whr-1166d)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "5:wan" "6@eth0"
;;
wizfi630a)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "0:wan" "6@eth0"
;;
*)
RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
if [ -n "${RT3X5X}" ]; then
ramips_setup_rt3x5x_vlans
else
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
fi
;;
esac
}
ramips_setup_macs()
{
local board="$1"
local lan_mac=""
local wan_mac=""
case $board in
a5-v11|\
ht-tm02|\
wmdr-143n)
lan_mac=$(cat /sys/class/net/eth0/address)
;;
all0239-3g|\
carambola|\
freestation5|\
w502u|\
wnce2001)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
bc2|\
broadway|\
d105|\
dir-300-b7|\
dir-320-b1|\
dir-620-a1|\
esr-9753|\
freestation5|\
hlk-rm04|\
mpr-a1|\
psr-680w|\
sl-r7205|\
y1|\
y1s)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
br-6475nd)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(mtd_get_mac_binary devdata 7)
;;
cy-swr1100|\
dch-m225)
lan_mac=$(mtd_get_mac_ascii factory lanmac)
;;
dir-645)
lan_mac=$(mtd_get_mac_ascii nvram lanmac)
wan_mac=$(mtd_get_mac_ascii nvram wanmac)
;;
dir-860l-b1)
lan_mac=$(mtd_get_mac_ascii factory lanmac)
wan_mac=$(mtd_get_mac_ascii factory wanmac)
;;
e1700)
wan_mac=$(mtd_get_mac_ascii config WAN_MAC_ADDR)
;;
gl-mt300n-v2)
wan_mac=$(mtd_get_mac_binary factory 4)
;;
hc5*61|\
hc5661a|\
hc5962)
lan_mac=`mtd_get_mac_ascii bdinfo "Vfac_mac "`
[ -n "$lan_mac" ] || lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
kn_rc|\
kn_rf|\
kng_rc)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
linkits7688 | \
linkits7688d)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(mtd_get_mac_binary factory 46)
;;
mac1200rv2)
lan_mac=$(mtd_get_mac_binary factory_info 13)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
miwifi-mini)
wan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$wan_mac")
;;
m3|\
m4-4M|\
m4-8M|\
x5|\
x8)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_add "$lan_mac" -2)
;;
newifi-d1)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_add "$lan_mac" 2)
;;
omega2|\
omega2p)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(mtd_get_mac_binary factory 46)
;;
oy-0001)
lan_mac=$(mtd_get_mac_binary factory 40)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
r6220)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
rt-n56u)
lan_mac=$(cat /sys/class/net/eth0/address)
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(mtd_get_mac_binary factory 32772)
;;
sk-wb8)
wan_mac=$(mtd_get_mac_binary factory 57350)
;;
tew-691gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3)
;;
tew-692gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 1)
;;
tiny-ac)
lan_mac=$(mtd_get_mac_ascii u-boot-env LAN_MAC_ADDR)
wan_mac=$(mtd_get_mac_ascii u-boot-env WAN_MAC_ADDR)
;;
vr500)
lan_mac=$(mtd_get_mac_binary factory 57344)
wan_mac=$(mtd_get_mac_binary factory 57350)
;;
w306r-v20)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 5)
;;
wcr-1166ds|\
wsr-1166)
local index="$(find_mtd_index "board_data")"
wan_mac="$(grep -m1 mac= "/dev/mtd${index}" | cut -d= -f2)"
lan_mac=$wan_mac
;;
wcr-150gn)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
whr-1166d|\
whr-300hp2|\
whr-600d|\
wsr-600)
wan_mac=$(mtd_get_mac_binary factory 4)
lan_mac=$wan_mac
;;
wizfi630a)
lan_mac=$(mtd_get_mac_binary factory 4)
wan_mac=$(mtd_get_mac_binary factory 40)
;;
wlr-6000)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 32772)" 2)
;;
*)
lan_mac=$(cat /sys/class/net/eth0/address)
wan_mac=$(macaddr_add "$lan_mac" 1)
;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
}
board_config_update
board=$(board_name)
ramips_setup_interfaces $board
ramips_setup_macs $board
board_config_flush
exit 0