a7c6cf5182
The AR8327 initvals were not copied to the DTS during the switch from mach file to device tree and broke the switch on the device. The former used PORT6 related initvals were wrong and have been corrected. The phy mode setting for the switch was missing in the DTS as well. The wireless requires an eeprom to work. The dual band wireless chips have both bands enabled by default but only one band per chip is working. The stock firmware uses the following mac addresses: LAN: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 5 GHz: AA:BB:CC:DD:EE:E8 Assuming the mac address range :E4 to :E8 is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: LAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E5 5 GHz: AA:BB:CC:DD:EE:E8 Signed-off-by: Mathias Kresin <dev@kresin.me>
147 lines
2.4 KiB
Text
147 lines
2.4 KiB
Text
/dts-v1/;
|
|
|
|
#include "rt3883.dtsi"
|
|
|
|
/ {
|
|
compatible = "TEW-692GR", "ralink,rt3883-soc";
|
|
model = "TRENDnet TEW-692GR";
|
|
|
|
nor-flash@1c000000 {
|
|
compatible = "cfi-flash";
|
|
reg = <0x1c000000 0x800000>;
|
|
bank-width = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
reg = <0x0 0x0030000>;
|
|
label = "u-boot";
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
reg = <0x00030000 0x00010000>;
|
|
label = "u-boot-env";
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
reg = <0x00040000 0x00010000>;
|
|
label = "factory";
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
reg = <0x00050000 0x007b0000>;
|
|
label = "firmware";
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 10 1>;
|
|
linux,code = <0x198>;
|
|
};
|
|
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio1 2 1>;
|
|
linux,code = <0x211>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wps {
|
|
label = "tew-692gr:orange:wps";
|
|
gpios = <&gpio0 9 1>;
|
|
};
|
|
|
|
wps2 {
|
|
label = "tew-692gr:green:wps";
|
|
gpios = <&gpio1 4 1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "spi", "i2c", "jtag", "uartf";
|
|
ralink,function = "gpio";
|
|
};
|
|
};
|
|
};
|
|
|
|
ðernet {
|
|
status = "okay";
|
|
mtd-mac-address = <&factory 0x4>;
|
|
|
|
port@0 {
|
|
phy-handle = <&phy0>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
phy-mode = "rgmii";
|
|
|
|
qca,ar8327-initvals = <
|
|
0x04 0x07600000 /* PORT0 PAD MODE CTRL */
|
|
0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
|
|
0x10 0x40000000 /* Power-on Strapping: 176-pin interface configuration */
|
|
0x50 0xc437c437 /* LED Control Register 0 */
|
|
0x54 0xc337c337 /* LED Control Register 1 */
|
|
0x58 0x00000000 /* LED Control Register 2 */
|
|
0x5c 0x03ffff00 /* LED Control Register 3 */
|
|
0x7c 0x0000007e /* PORT0_STATUS */
|
|
0x94 0x0000007e /* PORT6 STATUS */
|
|
>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pci {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pci_pins>;
|
|
|
|
pci_pins: pci {
|
|
pci {
|
|
ralink,group = "pci";
|
|
ralink,function = "pci-fnc";
|
|
};
|
|
};
|
|
|
|
host-bridge {
|
|
pci-bridge@1 {
|
|
status = "okay";
|
|
|
|
wmac@0,0 {
|
|
compatible = "ralink,rt2880-pci", "pciclass060400", "pciclass0604";
|
|
reg = < 0x10000 0 0 0 0 >;
|
|
ralink,2ghz = <0>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
ralink,mtd-eeprom = <&factory 0x0>;
|
|
ralink,5ghz = <0>;
|
|
};
|