6b94234a65
/etc/preinit has been the default init-script for a very long time (at least since Linux 2.6.30 in OpenWrt). Remove the kernel command line "init" parameter to get rid of duplicate and inconsistent definitions of this parameter (some boards, like FRITZ3370 for example did not use it at all, while it's just copy and paste on others). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
154 lines
2.8 KiB
Text
154 lines
2.8 KiB
Text
/dts-v1/;
|
|
|
|
#include "ar9.dtsi"
|
|
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
/ {
|
|
model = "FRITZ7320 - 1&1 HomeServer";
|
|
|
|
aliases {
|
|
led-boot = &power;
|
|
led-failsafe = &power;
|
|
led-running = &power;
|
|
|
|
led-internet = &info_green;
|
|
led-dsl = &power;
|
|
led-wifi = &wlan;
|
|
};
|
|
|
|
memory@0 {
|
|
reg = <0x0 0x4000000>;
|
|
};
|
|
|
|
fpi@10000000 {
|
|
localbus@0 {
|
|
nor-boot@0 {
|
|
compatible = "lantiq,nor";
|
|
bank-width = <2>;
|
|
reg = <0 0x0 0x1000000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
ath9k_cal: partition@0 {
|
|
label = "urlader";
|
|
reg = <0x00000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@20000 {
|
|
label = "firmware";
|
|
reg = <0x20000 0xf60000>;
|
|
};
|
|
|
|
partition@f80000 {
|
|
label = "tffs (1)";
|
|
reg = <0xf80000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@fc0000 {
|
|
label = "tffs (2)";
|
|
reg = <0xfc0000 0x40000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
gpio: pinmux@E100B10 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&state_default>;
|
|
|
|
state_default: pinmux {
|
|
pci {
|
|
lantiq,groups = "gnt1", "req1", "req2", "req3", "req4", "gnt2", "gnt3", "gnt4";
|
|
lantiq,function = "pci";
|
|
};
|
|
pci-in {
|
|
lantiq,groups = "req1", "req2", "req3", "req4";
|
|
lantiq,output = <0>;
|
|
lantiq,open-drain = <1>;
|
|
lantiq,pull = <2>;
|
|
};
|
|
pci-out {
|
|
lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4";
|
|
lantiq,output = <1>;
|
|
lantiq,pull = <0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
etop@E180000 {
|
|
phy-mode = "mii";
|
|
};
|
|
|
|
ifxhcd@E101000 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <100>;
|
|
|
|
rfkill {
|
|
label = "rfkill";
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RFKILL>;
|
|
};
|
|
dect {
|
|
label = "dect";
|
|
gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_PHONE>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
power: power {
|
|
label = "fritz7320:green:power";
|
|
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
|
|
default-state = "keep";
|
|
};
|
|
voice {
|
|
label = "fritz7320:green:fon";
|
|
gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
|
|
};
|
|
dect {
|
|
label = "fritz7320:green:dect";
|
|
gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
|
|
};
|
|
wlan: wlan {
|
|
label = "fritz7320:green:wlan";
|
|
gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
|
|
};
|
|
info_green: info_green {
|
|
label = "fritz7320:green:info";
|
|
gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
|
|
};
|
|
info_red {
|
|
label = "fritz7320:red:info";
|
|
gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pci0 {
|
|
status = "okay";
|
|
req-mask = <0xf>;
|
|
gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;
|
|
|
|
wifi@0,0 {
|
|
compatible = "pci0,0";
|
|
reg = <0x7000 0 0 0 0>;
|
|
qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */
|
|
};
|
|
};
|