400c5f03c3
Setting ipv6 to auto in case of a pppoe interface will trigger the creation of a dynamic wan_6 interface meaning two IPv6 interfaces (wan6 and wan_6) will be active on top of the pppoe interface. This leads to unpredictable behavior in the network; therefore set ipv6 to 1 which will prevent the dynamic creation of the wan_6 interface. Further alias the wan6 interface on top of the wan interface for pppoe as the wan6 interface can only be started when the link local address is ready. In case of pppoe the link local address is negotiated during the Internet Protocol Control Protocol when the PPP link is setup meaning all the IP address info is only available when the wan interface is up. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
434 lines
9.2 KiB
Bash
Executable file
434 lines
9.2 KiB
Bash
Executable file
#!/bin/sh
|
|
|
|
CFG=/etc/board.json
|
|
|
|
. /usr/share/libubox/jshn.sh
|
|
|
|
[ -s $CFG ] || /bin/board_detect || exit 1
|
|
[ -s /etc/config/network -a -s /etc/config/system ] && exit 0
|
|
|
|
generate_static_network() {
|
|
uci -q batch <<-EOF
|
|
delete network.loopback
|
|
set network.loopback='interface'
|
|
set network.loopback.ifname='lo'
|
|
set network.loopback.proto='static'
|
|
set network.loopback.ipaddr='127.0.0.1'
|
|
set network.loopback.netmask='255.0.0.0'
|
|
delete network.globals
|
|
set network.globals='globals'
|
|
set network.globals.ula_prefix='auto'
|
|
EOF
|
|
|
|
if json_is_a dsl object; then
|
|
json_select dsl
|
|
if json_is_a atmbridge object; then
|
|
json_select atmbridge
|
|
local vpi vci encaps payload
|
|
json_get_vars vpi vci encaps payload
|
|
uci -q batch <<-EOF
|
|
delete network.atm
|
|
set network.atm='atm-bridge'
|
|
set network.atm.vpi='$vpi'
|
|
set network.atm.vci='$vci'
|
|
set network.atm.encaps='$encaps'
|
|
set network.atm.payload='$payload'
|
|
EOF
|
|
json_select ..
|
|
fi
|
|
|
|
if json_is_a modem object; then
|
|
json_select modem
|
|
local type annex firmware tone xfer_mode
|
|
json_get_vars type annex firmware tone xfer_mode
|
|
uci -q batch <<-EOF
|
|
delete network.dsl
|
|
set network.dsl='dsl'
|
|
set network.dsl.annex='$annex'
|
|
set network.dsl.firmware='$firmware'
|
|
set network.dsl.tone='$tone'
|
|
set network.dsl.xfer_mode='$xfer_mode'
|
|
EOF
|
|
json_select ..
|
|
fi
|
|
json_select ..
|
|
fi
|
|
}
|
|
|
|
addr_offset=2
|
|
generate_network() {
|
|
local ifname macaddr protocol type ipaddr netmask
|
|
|
|
json_select network
|
|
json_select "$1"
|
|
json_get_vars ifname macaddr protocol ipaddr netmask
|
|
json_select ..
|
|
json_select ..
|
|
|
|
[ -n "$ifname" ] || return
|
|
|
|
# force bridge for multi-interface devices (and lan)
|
|
case "$1:$ifname" in
|
|
*\ * | lan:*) type="bridge" ;;
|
|
esac
|
|
|
|
uci -q batch <<-EOF
|
|
delete network.$1
|
|
set network.$1='interface'
|
|
set network.$1.type='$type'
|
|
set network.$1.ifname='$ifname'
|
|
set network.$1.proto='none'
|
|
EOF
|
|
|
|
[ -n "$macaddr" ] && uci -q batch <<-EOF
|
|
delete network.$1_dev
|
|
set network.$1_dev='device'
|
|
set network.$1_dev.name='$ifname'
|
|
set network.$1_dev.macaddr='$macaddr'
|
|
EOF
|
|
|
|
case "$protocol" in
|
|
static)
|
|
local ipad
|
|
case "$1" in
|
|
lan) ipad=${ipaddr:-"192.168.1.1"} ;;
|
|
*) ipad=${ipaddr:-"192.168.$((addr_offset++)).1"} ;;
|
|
esac
|
|
|
|
netm=${netmask:-"255.255.255.0"}
|
|
|
|
uci -q batch <<-EOF
|
|
set network.$1.proto='static'
|
|
set network.$1.ipaddr='$ipad'
|
|
set network.$1.netmask='$netm'
|
|
set network.$1.ip6assign='60'
|
|
EOF
|
|
;;
|
|
|
|
dhcp)
|
|
# fixup IPv6 slave interface if parent is a bridge
|
|
[ "$type" = "bridge" ] && ifname="br-$1"
|
|
|
|
uci -q batch <<-EOF
|
|
set network.$1.proto='dhcp'
|
|
delete network.${1}6
|
|
set network.${1}6='interface'
|
|
set network.${1}6.ifname='$ifname'
|
|
set network.${1}6.proto='dhcpv6'
|
|
EOF
|
|
;;
|
|
|
|
pppoe)
|
|
uci -q batch <<-EOF
|
|
set network.$1.proto='pppoe'
|
|
set network.$1.username='username'
|
|
set network.$1.password='password'
|
|
set network.$1.ipv6='1'
|
|
delete network.${1}6
|
|
set network.${1}6='interface'
|
|
set network.${1}6.ifname='@${1}'
|
|
set network.${1}6.proto='dhcpv6'
|
|
EOF
|
|
;;
|
|
esac
|
|
}
|
|
|
|
generate_switch_vlans_ports() {
|
|
local switch="$1"
|
|
local port ports role roles num attr val
|
|
|
|
#
|
|
# autogenerate vlans
|
|
#
|
|
|
|
if json_is_a roles array; then
|
|
json_get_keys roles roles
|
|
json_select roles
|
|
|
|
for role in $roles; do
|
|
json_select "$role"
|
|
json_get_vars ports
|
|
json_select ..
|
|
|
|
uci -q batch <<-EOF
|
|
add network switch_vlan
|
|
set network.@switch_vlan[-1].device='$switch'
|
|
set network.@switch_vlan[-1].vlan='$role'
|
|
set network.@switch_vlan[-1].ports='$ports'
|
|
EOF
|
|
done
|
|
|
|
json_select ..
|
|
fi
|
|
|
|
|
|
#
|
|
# write port specific settings
|
|
#
|
|
|
|
if json_is_a ports array; then
|
|
json_get_keys ports ports
|
|
json_select ports
|
|
|
|
for port in $ports; do
|
|
json_select "$port"
|
|
json_get_vars num
|
|
|
|
if json_is_a attr object; then
|
|
json_get_keys attr attr
|
|
json_select attr
|
|
uci -q batch <<-EOF
|
|
add network switch_port
|
|
set network.@switch_port[-1].device='$switch'
|
|
set network.@switch_port[-1].port=$num
|
|
EOF
|
|
|
|
for attr in $attr; do
|
|
json_get_var val "$attr"
|
|
uci -q set network.@switch_port[-1].$attr="$val"
|
|
done
|
|
json_select ..
|
|
fi
|
|
json_select ..
|
|
done
|
|
|
|
json_select ..
|
|
fi
|
|
}
|
|
|
|
generate_switch() {
|
|
local key="$1"
|
|
local vlans
|
|
|
|
json_select switch
|
|
json_select "$key"
|
|
json_get_vars enable reset blinkrate cpu_port
|
|
|
|
uci -q batch <<-EOF
|
|
add network switch
|
|
set network.@switch[-1].name='$key'
|
|
set network.@switch[-1].reset='$reset'
|
|
set network.@switch[-1].enable_vlan='$enable'
|
|
set network.@switch[-1].blinkrate='$blinkrate'
|
|
EOF
|
|
|
|
generate_switch_vlans_ports "$1"
|
|
|
|
json_select ..
|
|
json_select ..
|
|
}
|
|
|
|
|
|
generate_static_system() {
|
|
uci -q batch <<-EOF
|
|
delete system.@system[0]
|
|
add system system
|
|
set system.@system[-1].hostname='LEDE'
|
|
set system.@system[-1].timezone='UTC'
|
|
set system.@system[-1].ttylogin='0'
|
|
set system.@system[-1].log_size='64'
|
|
set system.@system[-1].urandom_seed='0'
|
|
|
|
delete system.ntp
|
|
set system.ntp='timeserver'
|
|
set system.ntp.enabled='1'
|
|
set system.ntp.enable_server='0'
|
|
add_list system.ntp.server='0.lede.pool.ntp.org'
|
|
add_list system.ntp.server='1.lede.pool.ntp.org'
|
|
add_list system.ntp.server='2.lede.pool.ntp.org'
|
|
add_list system.ntp.server='3.lede.pool.ntp.org'
|
|
EOF
|
|
|
|
if json_is_a system object; then
|
|
json_select system
|
|
local hostname
|
|
if json_get_var hostname hostname; then
|
|
uci -q set "system.@system[-1].hostname=$hostname"
|
|
fi
|
|
|
|
if json_is_a ntpserver array; then
|
|
local keys key
|
|
json_get_keys keys ntpserver
|
|
json_select ntpserver
|
|
uci -q delete "system.ntp.server"
|
|
|
|
for key in $keys; do
|
|
local server
|
|
if json_get_var server "$key"; then
|
|
uci -q add_list "system.ntp.server=$server"
|
|
fi
|
|
done
|
|
json_select ..
|
|
fi
|
|
json_select ..
|
|
fi
|
|
}
|
|
|
|
generate_rssimon() {
|
|
local key="$1"
|
|
local cfg="rssid_$key"
|
|
local refresh threshold
|
|
|
|
json_select rssimon
|
|
json_select "$key"
|
|
json_get_vars refresh threshold
|
|
json_select ..
|
|
json_select ..
|
|
|
|
uci -q batch <<-EOF
|
|
delete system.$cfg
|
|
set system.$cfg='rssid'
|
|
set system.$cfg.dev='$key'
|
|
set system.$cfg.refresh='$refresh'
|
|
set system.$cfg.threshold='$threshold'
|
|
EOF
|
|
}
|
|
|
|
generate_led() {
|
|
local key="$1"
|
|
local cfg="led_$key"
|
|
|
|
json_select led
|
|
json_select "$key"
|
|
json_get_vars name sysfs type trigger default
|
|
|
|
uci -q batch <<-EOF
|
|
delete system.$cfg
|
|
set system.$cfg='led'
|
|
set system.$cfg.name='$name'
|
|
set system.$cfg.sysfs='$sysfs'
|
|
set system.$cfg.trigger='$trigger'
|
|
set system.$cfg.default='$default'
|
|
EOF
|
|
|
|
case "$type" in
|
|
gpio)
|
|
local gpio inverted
|
|
json_get_vars gpio inverted
|
|
uci -q batch <<-EOF
|
|
set system.$cfg.trigger='gpio'
|
|
set system.$cfg.gpio='$gpio'
|
|
set system.$cfg.inverted='$inverted'
|
|
EOF
|
|
;;
|
|
|
|
netdev)
|
|
local device mode
|
|
json_get_vars device mode
|
|
uci -q batch <<-EOF
|
|
set system.$cfg.trigger='netdev'
|
|
set system.$cfg.mode='$mode'
|
|
set system.$cfg.dev='$device'
|
|
EOF
|
|
;;
|
|
|
|
usb)
|
|
local device
|
|
json_get_vars device
|
|
uci -q batch <<-EOF
|
|
set system.$cfg.trigger='usbdev'
|
|
set system.$cfg.interval='50'
|
|
set system.$cfg.dev='$device'
|
|
EOF
|
|
;;
|
|
|
|
usbport)
|
|
local ports port
|
|
json_get_values ports ports
|
|
uci set system.$cfg.trigger='usbport'
|
|
for port in $ports; do
|
|
uci add_list system.$cfg.port=$port
|
|
done
|
|
;;
|
|
|
|
rssi)
|
|
local iface minq maxq offset factor
|
|
json_get_vars iface minq maxq offset factor
|
|
uci -q batch <<-EOF
|
|
set system.$cfg.trigger='rssi'
|
|
set system.$cfg.iface='rssid_$iface'
|
|
set system.$cfg.minq='$minq'
|
|
set system.$cfg.maxq='$maxq'
|
|
set system.$cfg.offset='$offset'
|
|
set system.$cfg.factor='$factor'
|
|
EOF
|
|
;;
|
|
|
|
switch)
|
|
local port_mask speed_mask
|
|
json_get_vars port_mask speed_mask
|
|
uci -q batch <<-EOF
|
|
set system.$cfg.port_mask='$port_mask'
|
|
set system.$cfg.speed_mask='$speed_mask'
|
|
EOF
|
|
;;
|
|
|
|
portstate)
|
|
local port_state
|
|
json_get_vars port_state
|
|
uci -q batch <<-EOF
|
|
set system.$cfg.port_state='$port_state'
|
|
EOF
|
|
;;
|
|
|
|
timer|oneshot)
|
|
local delayon delayoff
|
|
json_get_vars delayon delayoff
|
|
uci -q batch <<-EOF
|
|
set system.$cfg.trigger='$type'
|
|
set system.$cfg.delayon='$delayon'
|
|
set system.$cfg.delayoff='$delayoff'
|
|
EOF
|
|
;;
|
|
esac
|
|
|
|
json_select ..
|
|
json_select ..
|
|
}
|
|
|
|
generate_gpioswitch() {
|
|
local cfg="$1"
|
|
|
|
json_select gpioswitch
|
|
json_select "$cfg"
|
|
local name pin default
|
|
json_get_vars name pin default
|
|
uci -q batch <<-EOF
|
|
delete system.$cfg
|
|
set system.$cfg='gpio_switch'
|
|
set system.$cfg.name='$name'
|
|
set system.$cfg.gpio_pin='$pin'
|
|
set system.$cfg.value='$default'
|
|
EOF
|
|
json_select ..
|
|
json_select ..
|
|
}
|
|
|
|
json_init
|
|
json_load "$(cat ${CFG})"
|
|
|
|
if [ ! -s /etc/config/network ]; then
|
|
touch /etc/config/network
|
|
generate_static_network
|
|
|
|
json_get_keys keys network
|
|
for key in $keys; do generate_network $key; done
|
|
|
|
json_get_keys keys switch
|
|
for key in $keys; do generate_switch $key; done
|
|
fi
|
|
|
|
if [ ! -s /etc/config/system ]; then
|
|
touch /etc/config/system
|
|
generate_static_system
|
|
|
|
json_get_keys keys rssimon
|
|
for key in $keys; do generate_rssimon $key; done
|
|
|
|
json_get_keys keys gpioswitch
|
|
for key in $keys; do generate_gpioswitch $key; done
|
|
|
|
json_get_keys keys led
|
|
for key in $keys; do generate_led $key; done
|
|
fi
|
|
uci commit
|